Pullman Holt Gloss Boss Polisher Installation guide

Operation & Care Instructions
Save For Future Reference
10702 N. 46th Street • Tampa, FL 33617
[phone] • Fax [phone] • www.pullman-holt.com
Model: Gloss Boss Polisher
Assembly Instructions:
1. Using a Phillips screwdriver, remove the screw from the
plastic handle. Slide metal handle tube into the plastic handle,
align the holes, reinstall and tighten the screw (see illustration
1).
2. Locate the other metal handle tube and slip the end with
one hole over the plastic handle connector on the finished
handle assembly. Make sure the locking pin protrudes through
the hole in the side of the lower tube (see illustration 2).
3. Remove the screw from the black painted yoke, and insert
the metal handle tube into the yoke. Reinstall the screw, and
tighten (see illustration 3).
Operating Instructions:
1. To operate, step on handle release, and tilt handle toward
the rear of the machine. The machine will start once the handle
is tilted a little.
2. To clean hard floors, attach the microfiber pads on the
brushes. Spray a small amount of a mild, water-based cleaner
on a small area of the floor and immediately run the machine
over the area. When the pads are dirty, they can be turned
over and re-attached. The dirty pads can be rinsed, or
laundered and reused indefinitely.
3. To Wax floors, apply wax to floor, and allow it to dry
completely. Attach felt discs to the scrubbing brushes. Snap
the plastic piece in the center of the felt disc onto the shaft in
the center of the brush, to securely retain the felt disc.
4. To clean carpet, spray a small section of the carpet with
an “encapsulating carpet cleaner”. Run the machine with
scrubbing brushes, on the carpet to work the chemical into the
fibers. Once the encapsulating cleaner has thoroughly dried,
vacuum it and the dirt out of the carpet. Encapsulating carpet
cleaner is a specialty chemical that can be purchased at most
vacuum cleaner shops, and janitorial supply stores.
Technical Information:
Voltage: 120, Frequency: 60 HZ
Power Requirement: 180 Watt
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
WARNING: To reduce the risk of fire, electrical shock, or injury:
1. Never carry the polisher by the cord, or yank the cord to
disconnect the polisher from an outlet; Instead grasp the plug,
and pull to disconnect.
2. Keep cord away from heated surfaces. Do not pull cord
around sharp edges or corners. Do not close door on the cord.
3. Do not contact moving parts. Do not use outdoors.
4. Do not leave appliance unattended, when plugged in.
Unplug from outlet when not in use, and before servicing.
5. Do not handle plug or appliance with wet hands.
6. Follow all label, and marking instructions.
7. Do not allow product to be used by children. Close
attention is needed when product is used near children.
8. Do not use with damaged cord, or plug. If appliance is not
working as it should, has been dropped, damaged, or dropped
into water, take it to an authorized service center.
9. Do not use with, or near flammable liquids.
10. Do not store appliance near hot ovens or heating
appliances.
11. Use only as described in this manual. Use only
manufacturer’s recommended attachments. Do not use for any
purpose other than described in this user’s guide.
12. Make sure the appliance is connected to the correct
voltage. The correct voltage is listed on the rating label.
13. Do not attempt to repair this product yourself. If the
product needs repair, take it to an authorized service center.
14. Do not submerge the appliance in water, or other liquid.
Do not place, or store the appliance where it can fall, or be
pulled into a tub, sink, or other vessel containing liquid. Do not
wash the machine.
15. If the machine is in need of repair, do not attempt to repair
it yourself. Take the machine to an authorized service center.
16. If using the machine to polish floor wax. Make sure the
wax is completely dry before polishing.
17. The polisher is equipped with a thermal limiting device, to
protect the motor from excessive temperature. If the polisher
suddenly stops operating, unplug the polisher, and allow it to
cool. If the appliance is left plugged in, it could start
unexpectedly when the motor cools.