Puls PIM90.241 User manual

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 1 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
POWER SUPPLY 1AC 24V 90W
•AC 100-240V Wide-range input
•Cost opti ized without co pro ising quality or
reliability
•No PE connection required
•Width only 36
•Efficiency up to 93.8%
•Low no-load power losses
•Full power between -10°C and +60°C
•Push-in ter inals
•3 Year warranty
PRODUCT DESCRIPTION SHORT-FORM DATA
The PIM90.241 is a DIN rail ountable single-phase-
input power supply, which provides a floating,
stabilized and galvanically separated SELV/PELV/ES1
output voltage.
The device is equipped with push-in ter inals, which
are opti ized for auto ated wiring.
The echanically robust housing is ade of a high-
grade, reinforced olded aterial, which per its
surrounding te peratures up to +70°C.
The unit is designed as “Class of Protection” II unit and
fulfills the safety and EMC require ents without an
input PE connection. This saves wiring costs.
The PIANO fa ily is a co pact industrial grade DIN rail
power supply series that focuses on the essential
features needed in today’s industrial applications. The
excellent cost/perfor ance ratio does not co pro ise
quality or reliability.
Output voltage DC 24V No inal
Adjust ent range 24-28V Factory setting 24.1V
Output current 3.8-3.2A Below +60°C a bient
2.8-2.4A At +70°C a bient
Derate between +60°C and +70°C
Input voltage AC AC 100-240V ± 10%
Mains frequency 50-60Hz ±6%
Input current AC 1.45 / 0.95A At 120 / 230Vac
Power factor 0.58 / 0.45 At 120 / 230Vac
Input inrush
current
18 / 40Apeak At 120 / 230Vac, +40°C,
cold start
Efficiency 92.1 / 93.8% At 120 / 230Vac
Power losses 7.9 / 6W At 120 / 230Vac
Hold-up ti e 25 / 119 s At 120 / 230Vac
Te perature
range
-10°C to +70°C
Size (w x h x d) 36x90x91 Without DIN rail
Weight 270g / 0.6lb
ORDER NUMBERS MAIN APPROVALS
Description: Power supply PIM90.241-xx
Order Number:
PIM90.241
For details and the co plete approval list, see chapter 18.
Ind. Cont. Eq.

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 2 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
Index
1 Intended Use....................................................... 3
2 Installation Instructions...................................... 3
3 AC-Input.............................................................. 4
4 DC-Input.............................................................. 5
5 Input Inrush Current.......................................... 5
6 Output................................................................. 6
7 Hold-up Ti e...................................................... 7
8 Efficiency and Power Losses.............................. 8
9 Lifeti e Expectancy........................................... 9
10 MTBF.................................................................... 9
11 Functional Diagra ............................................ 10
12 Ter inals And Wiring........................................ 10
13 Front Side And User Ele ents........................... 11
14 EMC..................................................................... 12
15 Environ ent....................................................... 13
16 Safety and Protection Features......................... 14
17 Dielectric Strength.............................................. 14
18 Approved, Fulfilled or Tested Standards........... 15
19 Regulatory Product Co pliance........................ 15
20 Physical Di ensions And Weight...................... 16
21 Application Notes............................................... 17
21.1 Charging of Batteries.............................. 17
21.2 Series Operation...................................... 17
21.3 Parallel Use to Increase Output Power... 17
21.4 Parallel Use for 1+1 Redundancy........... 17
21.5 Two Phase Operation............................. 17
21.6 Use in a Tightly Sealed Enclosure........... 17
The infor ation given in this docu ent is correct to the best of our knowledge and experience at the ti e of publication.
If not expressly agreed otherwise, this infor ation does not represent a warranty in the legal sense of the word. As the
state of our knowledge and experience is constantly changing, the infor ation in this data sheet is subject to revision. We
therefore kindly ask you to always use the latest issue of this docu ent (available under www.pulspower.co ).
No part of this docu ent ay be reproduced or utilized in any for without our prior per ission in writing.
Packaging and packaging aids can and should always be recycled. The product itself ay not be disposed of as do estic
refuse.
TERMINOLOGY AND ABBREVIATIONS
PE and S mbol PE is the abbreviation for Protective Earth and has the sa e eaning as the sy bol .
Earth, Ground This docu ent uses the ter “earth” which is the sa e as the U.S. ter “ground”.
t.b.d. To be defined, value or description will follow later.
AC 230V A figure displayed with the AC or DC before the value represents a no inal voltage with
standard tolerances (usually ±15%) included.
E.g.: DC 12V describes a 12V battery disregarding whether it is full (13.7V) or flat (10V)
230Vac A figure with the unit (Vac) at the end is a o entary figure without any additional
tolerances included.
50Hz vs. 60Hz As long as not otherwise stated, AC 100V and AC 230V para eters are valid at 50Hz ains
frequency. AC 120V para eters are valid for 60Hz ains frequency.
ma A key word indicating flexibility of choice with no i plied preference.
shall A key word indicating a andatory require ent.
should A key word indicating flexibility of choice with a strongly preferred i ple entation.

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 3 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
1. Intended Use
This device is designed for installation in an enclosure and is intended for co ercial use, such as in industrial control,
process control, onitoring, easure ent, Audio/Video, infor ation or co unication equip ent or the like.
Do not use this device in equip ent, where alfunctioning ay cause severe personal injury or threaten hu an life without
additional appropriate safety devices, that are suited for the end-application. If this device is used in a anner outside of
its specification, the protection provided by the device ay be i paired.
Do not use this device on AC 100V ains with ore than 2.9A load when the application is sensitive to short output voltage
dips during ains interruptions even with a length shorter than 20 s.
2. Installation Instructions
DANGER Risk of electrical shock, fire, personal injur or death.
– Turn power off before working on the device. Protect against inadvertent re-powering.
– Do not open, odify or repair the device.
– Use caution to prevent any foreign objects fro entering the housing.
– Do not use in wet locations or in areas where oisture or condensation can be expected.
– Do not touch during power-on, and i ediately after power-off. Hot surfaces ay cause burns.
Obe the following installation instructions:
This device ay only be installed and put into operation by qualified personnel. This device does not contain serviceable
parts. The tripping of an internal fuse is caused by an internal defect. If da age or alfunction should occur during
installation or operation, i ediately turn power off and send unit to the factory for inspection.
Install device in an enclosure providing protection against electrical, echanical and fire hazards. Install the device onto a
DIN rail according to EN 60715 with the input ter inals on the botto of the device.
Make sure that the wiring is correct by following all local and national codes. Use appropriate copper cables that are
designed for a ini u operating te perature of +60°C for a bient te peratures up to +45°C, +75°C for a bient
te peratures up to +60°C and +90°C for a bient te peratures up to +70°C. Ensure that all strands of a stranded wire
enter the ter inal connection.
The device is designed for pollution degree 2 areas in controlled environ ents. No condensation or frost is allowed. The
enclosure of the device provides a degree of protection of IP20. The enclosure does not provide protection against spilled
liquids.
The device is designed for overvoltage category II zones. Below 2000 altitude the device is tested for i pulse withstand
voltages up to 4kV, which corresponds to OVC III according to IEC 60664-1.
The device is designed as “Class of Protection” II equip ent according to IEC 61140.
The device is suitable to be supplied fro TN, TT or IT ains networks. The continuous voltage between the input ter inal
and the PE potential ust not exceed 300Vac. A disconnecting eans shall be provided for the input of the device.
The device is designed for convection cooling and does not require an external fan. Do not obstruct airflow and do not
cover ventilation grid!
The device is designed for altitudes up to 5000 (16 400ft). Above 2000 (6560ft) a reduction in output current is required.
Keep the following ini u installation clearances: 40 on top, 20 on the botto , 0 left and right side. Increase
the 0 to 15 in case the adjacent device is a heat source.
The device is designed, tested and approved for branch circuits up to 20A without additional protection device. If an
external fuse is utilized, do not use circuit breakers s aller than 6A B- or 4A C-Characteristic to avoid a nuisance tripping
of the circuit breaker.
The axi u surrounding air te perature is +70°C (158°F). The operational te perature is the sa e as the a bient or
surrounding air te perature and is defined 2c below the device. The device is designed to operate in areas between 5%
and 95% relative hu idity.

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 4 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
3. AC-Input
The device is suitable to be supplied fro TN, TT or IT ains networks.
AC input no . AC 100-240V
AC input range 90-264Vac Continuous operation
264-300Vac For axi u 500 s
Allowed voltage L or N to
earth
ax. 300Vac Continuous, according to IEC 60664-1
Input frequency no . 50-60Hz ±6%
Turn-on voltage typ. 75Vac Steady-state value, see Fig. 3-1
Shut-down voltage typ. 54Vac Steady-state value, see Fig. 3-1
External input protection See reco endations in chapter 2.
AC 100V AC 120V AC 230V
Input current typ. 1.69A 1.45A 0.95A At 24V, 3.8A, see Fig. 3-1
Power factor typ. 0.6 0.58 0.45 At 24V, 3.8A, see Fig. 3-4
Start-up delay typ. 50 s 50 s 50 s See Fig. 3-2
typ. 21 s 21 s 20 s At 24V, 3.8A constant current load,
0 F load capacitance, see Fig. 3-2
Rise ti e
typ. 42 s 42 s 40 s At 24V, 3.8A constant current load,
2 F load capacitance, see Fig. 3-2
Turn-on overshoot ax. 100 V 100 V 100 V See Fig. 3-2
Fig. 3-1: Input voltage range Fig. 3-2: Turn-on behavior, definitions
Fig. 3-3: Input current vs. output
load at 24V output voltage
Fig. 3-4: Power factor vs. output
load at 24V output voltage

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 5 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
4. DC-Input
Do not operate this device with DC-input voltage.
5. Input Inrush Current
A NTC li its the input inrush current after turn-on of the input voltage. The inrush current is input voltage and a bient
te perature dependent. The output load has no i pact on the inrush current value.
The charging current into EMI suppression capacitors is disregarded in the first icroseconds after switch-on.
AC 100V AC 120V AC 230V
typ. 14A 18A 40A At 40°C, a bient, cold startInrush current Ipeak
typ. 12A 16A 35A At 25°C, a bient, cold start
ax. 17A 22A 48A At 40°C, a bient, cold start
ax. 15A 20A 43A At 25°C, a bient, cold start
Inrush energy I2t ax. 0.3A2s 0.4A2s 1.7A2s At 40°C, a bient, cold start
Fig. 5-1: Typical turn-on behavior
at 120Vac and 25°C a bient
Fig. 5-2: Zoo into the first inrush peak
Fig. 5-3: Typical turn-on behavior
at 230Vac and 25°C a bient
Fig. 5-4: Zoo into the first inrush peak

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 6 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
6. Output
The output provides a SELV/PELV/ES1 rated voltage, which is galvanically isolated fro the input voltage. The output is
electronically protected against no-load, overload and short circuit. In case of a protection event, audible noise ay occur.
The output is designed to supply any kind of loads, including inductive and capacitive loads. Capacitive loads should not
be larger than 4 000μF with 3.8A or 5 000μF with 1.9A additional resistive load.
At heavy overloads (when output voltage falls below 14V), the device delivers continuous output current for 20 s. After
this, the output is switched off for approx. 160 s before a new start atte pt is auto atically perfor ed. This cycle is
repeated as long as the overload exists.
If the overload has been cleared, the device will operate nor ally.
Output voltage no . DC 24V
Adjust ent range 24-28V Guaranteed value
ax. 29.5V This is the axi u output voltage which can occur at
the clockwise end position of the potentio eter due
to tolerances. It is not a guaranteed value which can be
achieved.
Factory settings typ. 24.1V ±0,2%, at full load, cold unit
Line regulation ax. 10 V Between 90 and 300Vac
Load regulation ax. 100 V Between 0 and 3.8A, static value, see Fig. 6-1
Ripple and noise voltage ax. 100 Vpp Bandwidth 20Hz to 20MHz, 50Oh
Output current no . 3.8A At 24V and an a bient te perature below 60°C
no . 2.8A At 24V and 70°C a bient te perature
no . 3.2A At 28V and an a bient te perature below 60°C
no . 2.4A At 28V and 70°C a bient te perature
Overload protection Included Electronically protected against no-load, overload and
short circuit. In case of a protection event, audible noise
ay occur.
Overload behaviour Continuous current For output voltage above 14Vdc, see Fig. 6-1
Inter ittent current For output voltage below 14Vdc, see Fig. 6-2
ax. 6.7A Continuous current, see Fig. 6-1Overload/
short-circuit current typ. 8.6A Inter itted current peak value for typ. 20 s
Load i pedance 150 Oh , see Fig. 6-2
Discharge current of output capacitors is not included.
ax. 3.2A Inter itted current average value (R.M.S.)
Load i pedance 150 Oh , see Fig. 6-2
Output capacitance typ. 1 600μF Included inside the device
Back-feeding loads ax. 35V The unit is resistant and does not show alfunctioning
when a load feeds back voltage to the device. It does not
atter whether the device is on or off. The absorbing
energy can be calculated according to the built-in large
sized output capacitor.
Fig. 6-1: Output voltage vs. output current, typ. Fig. 6-2: Inter ittend current at short circuit, typ.*)
*) with cold devices the ti es are about 15% longer.

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 7 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
7. Hold-up Ti e
The hold-up ti e is the ti e during which a device’s output voltage re ains within specification following the loss of input
power. The hold-up ti e is output load dependent. At no load, the hold-up ti e can be up to several seconds. The green
DC-OK LED is also on during this ti e.
AC 100V AC 120V AC 230V
Hold-up ti e typ. 14 s 25 s 119 s At 24V, 3.8A
typ. 40 s 60 s 242 s At 24V, 1.9A
in. 11.5 s 20 s 95 s At 24V, 3.8A
in. 32 s 48 s 194 s At 24V, 1.9A
Fig. 7-1: Hold-up ti e vs. input voltage Fig. 7-2: Shut-down behaviour, definitions

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 8 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
8. Efficiency and Power Losses
AC 100V AC 120V AC 230V
Efficiency typ. 90.6% 92.1% 93.8% At 24V, 3.8A (full load)
Average efficiency typ. 90.5% 91.6% 92% 25% at 0.95A, 25% at 1.9A,
25% at 2.85A, 25% at 3.8A
Power losses typ. 0.3W 0.3W 0.4W At no load
typ. 5W 4.3W 3.8W At 24V, 1.9A (half load)
typ. 9.5W 7.9W 6W At 24V, 3.8A (full load)
The average efficiency is an assu ption for a typical application where the device is loaded with 25% of the no inal
load for 25% of the ti e, 50% of the no inal load for another 25% of the ti e, 75% of the no inal load for another
25% of the ti e and with 100% of the no inal load for the rest of the ti e.
Fig. 8-1: Efficiency vs. output current at 24V, typ. Fig. 8-2: Losses vs. output current at 24V, typ.
Fig. 8-3: Efficiency vs. input voltage at 24V, 3.8A, typ. Fig. 8-4: Losses vs. input voltage at 24V, 3.8A, typ.

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 9 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
9. Lifeti e Expectancy
The Lifeti e expectancy shown in the table indicates the ini u operating hours (service life) and is deter ined by
the lifeti e expectancy of the built-in electrolytic capacitors. Lifeti e expectancy is specified in operational hours and is
calculated according to the capacitor’s anufacturer specification.
Please note: The anufacturer of the electrolytic capacitors only guarantees a axi u life of up to 15 years (131 400h).
Any nu ber exceeding this value is a calculated theoretical lifeti e which can be used to co pare devices.
AC 100V AC 120V AC 230V
Lifeti e expectancy 39 000h 64 000h 102 000h At 24V, 3.8A and 40°C
260 000h 292 000h 309 000h At 24V, 1.9A and 40°C
91 000h 147 000h 287 000h At 24V, 3.8A and 25°C
640 000h 720 000h 815 000h At 24V, 1.9A and 25°C
10. MTBF
MTBF stands for Mean Ti e Between Failure, which is calculated according to statistical device failures, and indicates
reliability of a device. It is the statistical representation of the likelihood of a unit to fail and does not necessarily represent
the life of a product.
The MTBF figure is a statistical representation of the likelihood of a device to fail. A MTBF figure of e.g. 1 000 000h eans
that statistically one unit will fail every 100 hours if 10 000 units are installed in the field. However, it cannot be deter ined
if the failed unit has been running for 50 000h or only for 100h.
For these types of units the MTTF (Mean Ti e To Failure) value is the sa e value as the MTBF value.
AC 100V AC 120V AC 230V
MTBF SN 29500, IEC 61709 1 174 000h 1 273 000h 1 507 000h At 24V, 3.8A and 40°C
2 251 000h 2 406 000h 2 752 000h At 24V, 3.8A and 25°C
MTBF MIL HDBK 217F 751 000h 760 000h 698 000h At 24V, 3.8A and 40°C; Ground Benign GB40
1 085 000h 1 099 000h 1 018 000h At 24V, 3.8A and 25°C; Ground Benign GB25
219 000h 224 000h 220 000h At 24V, 3.8A and 40°C; Ground Fixed GF40
288 000h 294 000h 293 000h At 24V, 3.8A and 25°C; Ground Fixed GF25

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 10 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
11. Functional Diagra
Fig. 11-1: Functional diagra
12. Ter inals And Wiring
The ter inals are IP20 Finger safe constructed and suitable for field- and factory wiring.
All Terminals
T pe Push-in ter inals
Solid wire ax. 2.5 2
Stranded wire ax. 2.5 2
Stranded wire with ferrules ax. 1.5 2
A erican Wire Gauge AWG 24-12
Max. wire dia eter (including ferrules) 2.3
Wire stripping length 10 / 0.4inch
Screwdriver 3 slotted to open the spring

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 11 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
13. Front Side And User Ele ents
A Input Terminals
NNeutral conductor input
LPhase (Line) input
B OutputTerminals
Dual ter inals for the negative and positive pole.
Both poles are internally connected.
+Positive output
- Negative (return) output
C DC OK LED (green)
The LED is on, when the output voltage is above 18V.
Fig. 13-1: Front side
D Output voltage adustment potentiometer

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 12 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
14. EMC
The EMC behavior of the device is designed for applications in industrial environ ent as well as in residential, co ercial
and light industry environ ents.
The device co plies with EN 61000-6-1, EN 61000-6-2, EN 61000-6-3, EN 61000-6-4, EN 61000-3-2 and EN 61000-3-3. The
device co plies with FCC Part 15 rules. Operation is subjected to following two conditions: (1) this device ay not cause
har ful interference, and (2) this device ust accept any interference received, including interference that ay cause
undesired operation.
Do not use this device on AC 100V ains with ore than 2.9A load when the application is sensitive to short output voltage
dips during ains interruptions even with a length shorter than 20 s.
EMC Immunit
Electrostatic discharge EN 61000-4-2 Contact discharge 8kV Criterion A
Air discharge 8kV Criterion A
Electro agnetic RF field EN 61000-4-3 80MHz - 6GHz 10V/ Criterion A
Fast transients (Burst) EN 61000-4-4 Input lines 4kV Criterion A
Output lines 2kV Criterion A
Surge voltage on input EN 61000-4-5 L → N 2kV Criterion A
N / L → Earthed output 4kV Criterion A
Surge voltage on output EN 61000-4-5 (+) → (−) 1kV Criterion A
(+) → (−) Earthed 1kV Criterion A
(−) → (+) Earthed 1kV Criterion A
Conducted disturbance EN 61000-4-6 0.15 - 80MHz 10V Criterion A
Voltage dips EN 61000-4-11 0% of 100Vac 0Vac, 20 s Criterion A/C
40% of 100Vac 40Vac, 200 s Criterion C
70% of 100Vac 70Vac, 500 s Criterion A
0% of 120Vac 0Vac, 20 s Criterion A
40% of 120Vac 48Vac, 200 s Criterion C
70% of 120Vac 84Vac, 500 s Criterion A
0% of 200Vac 0Vac, 20 s Criterion A
40% of 200Vac 80Vac, 200 s Criterion A
70% of 200Vac 140Vac, 500 s Criterion A
Voltage interruptions EN 61000-4-11 0V 5000 s Criterion C
Powerful transients VDE 0160 Over entire load range 750V, 1.3 s Criterion A
Performance criterions:
A: The device shows nor al operation behavior within the defined li its.
B: The device operates continuously during and after the test. During the test inor te porary i pair ents ay
occur, which will be corrected by the device itself.
C: Te porary loss of function is possible. The device ay shut-down and restarts by itself. No da age or hazards
for the device will occur.
A/C: Criterion A for output current below 2.9A and criterion C for output currents above 2.9A.
EMC Emission
Conducted e ission input lines EN 55011, EN 55032, FCC Part 15, CISPR 11,
CISPR32
Class B
Conducted e ission output lines IEC/CISPR 16-1-2, IEC/CISPR 16-2-1 Li its for local DC power networks
fulfilled.
Radiated e ission EN 55011, EN 55032, CISPR 11, CISPR 32 Class B
Har onic input current EN 61000-3-2 Fulfilled (Class A)
Voltage fluctuations, flicker EN 61000-3-3 Fulfilled, tested with non pulsing
constant current loads.
Switching Frequencies
Main converter 5kHz to 120kHz Input voltage and output load
dependent

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 13 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
15. Environ ent
Operational te perature -10°C to +70°C (14°F to 158°F) The operational te perature is the a bient or
surrounding te perature and is defined as the
air te perature 2c below the device.
Storage te perature -40°C to +85°C (-40°F to 185°F) For storage and transportation
Output derating 0.1A/°C Between +60°C and +70°C (140°F to 158°F)
0.25A/1000 or 5°C/1000 For altitudes >2000 (6560ft), see Fig. 15-2
The derating is not hardware controlled. The user has to take this into consideration to
stay below the derated current li its in order not to overload the unit.
Hu idity 5 to 95% r.h. According to IEC 60068-2-30
No condensation allowed.
At ospheric pressure 110-54kPa See Fig. 15-2 for details
Altitude Up to 5000 (16 400ft) See Fig. 15-2 for details
Over-voltage category II According to IEC 60664-1, for altitudes
<5000
I pulse withstand voltage 4kV (according to over-voltage
category III)
Input to PE
According to IEC 60664-1, for altitudes
<2000
Degree of pollution 2 According to IEC 60664-1, non conductive
Vibration sinusoidal 2-17.8Hz: ±1.6
17.8-500Hz: 2g
2 hours / axis
According to IEC 60068-2-6
Shock 30g 6 s, 20g 11 s
3 bu ps / direction, 18 bu ps in total
According to IEC 60068-2-27
Shock and vibration is tested in co bination with DIN rails according to EN 60715 with
a height of 15 and a thickness of 1.3 .
Fig. 15-1: Output power vs. a bient te p. Fig. 15-2: Output power vs. altitude

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 14 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
16. Safety and Protection Features
Isolation resistance >500MOh At delivered condition between input and output,
easured with 500Vdc
Output over-voltage protection typ. 30.5Vdc
ax. 32Vdc
In case of an internal defect, a redundant circuit li its the axi u output
voltage to 32V. The output shuts down. To atte pt a restart, turn the input
power off for at least 90s.
Class of protection II According to IEC 61140
Degree of protection IP20 According to EN/IEC 60529
Over-te perature protection Not Included
Input transient protection MOV (Metal Oxide Varistor) For protection values see chapter 14 (EMC).
Internal input fuse Included Not user replaceable slow-blow high-braking
capacity fuse
typ. 50μA / 120μA At 100Vac, 50Hz, TN-, TT- ains / IT- ains
typ. 75μA / 170μA At 120Vac, 60Hz, TN-, TT- ains / IT- ains
typ. 130μA / 270μA At 230Vac, 50Hz, TN-, TT- ains / IT- ains
ax. 80μA / 190μA At 110Vac, 50Hz, TN-, TT- ains / IT- ains
ax. 120μA / 270μA At 132Vac, 60Hz, TN-, TT- ains / IT- ains
Touch current (leakage current)
ax. 210μA / 400μA At 264Vac, 50Hz, TN-, TT- ains / IT- ains
17. Dielectric Strength
The output voltage is floating and has no oh ic connection to the ground.
The output is insulated to the input by a double or reinforced insulation.
Type and routine tests are conducted by the anufacturer. Field tests ay be conducted in the field using the appropriate
test equip ent which applies the voltage with a slow ra p (2s up and 2s down). Connect all phase-ter inals together
as well as all output poles before conducting the test. When testing, set the cut-off current settings to the value in the
table below.
It is reco ended that either the (+) pole or the (–) pole shall be connected to the protective earth syste . This helps to
avoid situations in which a load starts unexpectedly or cannot be switched off when unnoticed earth faults occur.
Fig. 17-1: Dielectric strength
A
Type test 60s 3000Vac
Factory test 5s 2500Vac
Field test 5s 2000Vac
Field test cut-off current
settings
>4 A

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 15 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
18. Approved, Fulfilled or Tested Standards
IEC 61010 CB Sche e Certificate
IEC 61010-2-201 - Electrical Equip ent for Measure ent, Control and
Laboratory Use - Particular require ents for control equip ent
IEC 62368 CB Sche e Certificate
IEC 62368-1 - Audio/video, infor ation and co unication
technology equip ent - Safety require ents
Output safety level: ES1
UL 61010 UL Certificate
Listed equip ent for category NMTR - UL 61010-2-201 - Electrical
equip ent for easure ent, control and laboratory use - Particular
require ents for control equip ent
Applicable for US and Canada
E-File: E198865
IEC 61558-2-16
(Annex BB)
Safety Isolating
Transfor er
Test Certificate
IEC 61558-2-16 - Safety of transfor ers, reactors, power supply units
and si ilar products for supply voltages up to 1100V
Particular require ents and tests for switch ode power supply units
and transfor ers for switch ode power supply units
ISA-71.04-1985 Manufacturer's Declaration (Online Docu ent)
Airborne Conta inants Corrosion Test
Severity Level: G3 Harsh
H2S: 100ppb
NOx: 1250ppb
Cl2: 20ppb
SO2: 300ppb
Test Duration: 3 weeks, which si ulates a service life of at least 10
years
VDMA 24364 Paint Wetting I pair ent Substances Test (or LABS-Test)
Tested for Zone 2 and Test Class C1 according to VDMA 24364-C1-L/W
for solvents and water-based paints
19. Regulatory Product Co pliance
EU Declaration of
Confor ity
The CE ark indicates confor ance with the European
– EMC directive
– Low-voltage directive (LVD)
– RoHS directive
REACH Regulation Manufacturer's Declaration
EU Regulation regarding the Registration, Evaluation, Authorization
and Restriction of Che icals
EU Regulation 1907/2006
WEEE Regulation Manufacturer's Declaration
EU Directive on Waste Electrical and Electronic Equip ent Registered
in Ger any as business to business (B2B) products.
EU Directive 2012/19/EU
RoHS (China RoHS 2) Manufacturer's State ent
Ad inistrative Measures for the Restriction of the Use of Hazardous
Substances in Electrical and Electronic Products 25 years
EAC TR Registration EAC Certificate
EAC EurAsian Confor ity - Registration Russia,
Kazakhstan and Belarus
8504408200, 8504409000

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 16 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
20. Physical Di ensions And Weight
Width 36 / 1.42''
Height 90 / 3.54''
Depth 91 / 3.58''
The DIN rail height ust be added to the unit depth to calculate the total required
installation depth.
Weight 270g / 0.6lb
DIN rail Use 35 DIN rails according to EN 60715 or EN 50022 with a height of 7.5 or 15 .
Housing aterial High-grade polycarbonate / ABS blend aterial
Installation clearances See chapter 2.
Penetration protection S all parts like screws, nuts, etc. with a dia eter larger than 4.2 .
Fig. 20-1: Front view Fig. 20-2: Side view
All di ensions in unless otherwise noted.

PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN www.pulspower.co 17 / 17
All para eters are specified at 24V, 3.8A, 230Vac, 25°C a bient and after a 5 inutes run-in ti e unless otherwise noted.
21. Application Notes
21.1. CHARGING OF BATTERIES
Do not use the power supply to charge batteries.
21.2. SERIES OPERATION
Power supplies of the sa e type can be connected in series for higher output
voltages. It is possible to connect as any units in series as needed, providing the
su of the output voltage does not exceed 150Vdc. Voltages with a potential
above 60Vdc ust be installed with a protection against touching.
Avoid return voltage (e.g. fro a decelerating otor or battery) which is applied
to the output ter inals.
Keep an installation clearance of 15 (left / right) between two power supplies
and avoid installing the power supplies on top of each other.
Pay attention that leakage current, EMI, inrush current, har onics will increase
when using ultiple power supplies.
21.3. PARALLEL USE TO INCREASE OUTPUT POWER
Do not use parallel devices for higher output currents.
21.4. PARALLEL USE FOR 1+1 REDUNDANCY
Do not use this device to build redundant syste s since there is no onitoring (DC-OK signal) included.
21.5. TWO PHASE OPERATION
The power supply can also be operated on two phases of a three-phase-syste .
Such a phase-to-phase connection is allowed as long as the supplying voltage is
below 240V+10%.
Ensure that the wire, which is connected to the N-ter inal, is appropriately fused.
21.6. USE IN A TIGHTLY SEALED ENCLOSURE
When the power supply is installed in a tightly sealed enclosure, the te perature inside the enclosure will be higher than
outside. In such situations, the inside te perature defines the a bient te perature for the power supply.
The power supply is placed in the iddle of the box, no other heat producing ite s are inside the box. The te perature
sensor inside the box is placed in the iddle of the right side of the power supply with a distance of 1c . The following
easure ent results can be used as a reference to esti ate the te perature rise inside the enclosure.
Case A Case B
Enclosure size 110x180x165
Rittal Typ IP66 Box
PK 9516 100
plastic
110x180x165
Rittal Typ IP66 Box
PK 9516 100
plastic
Input voltage 230Vac 230Vac
Load 24V, 3.04A; (=80%) 24V, 3.8A; (=100%)
Te perature inside the box 30.3°C 31.7°C
Te perature outside the box 21°C 21°C
Te perature rise 9.3K 10.7K