Pure Edge 3 X 100 User manual

1
- Do not install this power supply in a wet location.
- To reduce the risk of the system overheating and possibly
causing a fire, make sure all the connections are tight.
- Do not install *LED fixture closer than three inches or as
specified in the *LED fixture installation instructions to
curtains or similarly combustible materials. Keep insulation
at least 3" away from the enclosure.
- Turn the electrical power off before modifying the lighting
system in any way.
- The system is "ETL" listed for USA and Canada only when
all the products used are supplied by Edge Lighting.
* See LED fixture installation instructions for proper
placement.
- RISK OF FIRE: This product must be installed by a
qualified electrician. Turn the power to the electrical box off
during installation. Read the "Important Safety Instructions"
before installation.
- NOTE: To avoid overheating the power supply, install it in a
ventilated remote location where air flows. Maintain proper
spacing among power supplies when multiple power
supplies are installed in the same remote location.
- This product is not suitable for wet locations. It is approved
for the use at any height above the finished floor.
- A typical installation is shown. Specific installation must be
in accordance with the local electrical codes.
- TO REDUCE RISK OF FIRE, it is important to wire the
power supply for the system as described in this
installation instruction.
- Load each power supply to MAXIMUM 100 Watts.
- Use CDP color dial or CTP color touch screen controller with
RGB LED soft strip.
GENERAL INFORMATION IMPORTANT SAFETY INSTRUCTIONS
Installation Instructions for 2 X 100 / 3 X 100 / 4 X 100 Watt 24 Volt DC
RGB DMX LED Power Supply
SAVE THESE INSTRUCTIONS!
VOLTAGE
DROP
UP TO 31FT
3% 32FT-49FT
WIRE SIZE
VOLTAGE AT END
OF THE WIRE
14 AWG
23.28 VAC
50FT-81FT 82FT-124FT
12 AWG
23.29 VAC
10 AWG 8 AWG
23.28 VAC 23.28 VAC
WIRE LENGTH
IN FT
100W, 24VAC LOW VOLTAGE WIRE SIZE CHART
Doc # 904-PSB-2_3_4X100W-24VDC-RGB_06
1718 W. Fullerton Chicago, IL 60614
Ph: 773.770.1195 ● Fax: [phone]
www.PureEdgeLighting.com ● [email protected]
© 2016 PureEdge Lighting. All Rights Reserved.

2
Using LED Power Supply with RGB Soft Strip & CDP or CTP
Controller
M
A
COVER
PHILLIPS SCREW
ENCLOSURE
DVR-RGB-60
COVER 2
1: Loosen the six Phillips screws on front of the power supply to
remove the cover.
2: Carefully pull off the cover from the DVR-RGB-60 driver.
M
M
B
ELECTRICAL BOX
CONDUIT
7
9
CONTROLLER
CONTROLLER
POWER SUPPLY
DMX CABLE (BELDEN #9841)
3: Connect one end of a red wire to the "VDC+" terminal of the
controller and the other end to the "+24VDC" terminal of the
controller power supply.
4: Connect one end of a black wire to the "Ground" terminal of
the controller and the other end to the "-24VDC" terminal of
the controller power supply.
5: Connect the white wire to the "N" terminal of the controller
power supply.
6: Connect the black wire to the "L" terminal of the controller
power supply.
7: Install conduits from the controller, main panel (line voltage),
and soft strip to the power supply enclosure.
8: Run the black and white line voltage wires coming from
the controller power supply to the power supply enclosure.
9: Run the proper size DMX cable (Belden #9841
recommended) with three data wires from controller to the
power supply box.
NOTE: Use a deep double gang boxes to fit the controller
and controller power supply.
3
4
6
5
8
NOTE: Refer to the "Configuring and Operating Dim Wheel"
on pages 5 and 6 to properly operate the controller.
POWER SUPPLY
1

M
C10: Install a red wire from the power supply to DVR-RGB-60
"VDC+" red terminal and a black wire from power supply
to DVR-RGB-60 "VDC-" blue terminal.
11: Connect one end of a data wire (blue with white stripes
wire) to controller "LEDSYNC OUT–" terminal. Connect the
other end into the DVR-RGB-60 "DMX in –" terminal.
12: Connect one end of a data wire (white with blue stripes
wire) to controller "LEDSYNC OUT+" terminal. Connect the
other end into the DVR-RGB-60 "DMX in +" terminal.
13: Connect one end of a data wire (bare shield wire) to
controller "LEDSYNC SHIELD" terminal. Connect the other
end into the DVR-RGB-60 "DMX in shield" terminal.
M
M
NOTE: "DMX in+", "DMX in-", "EXT in+" & "EXT in-", controller
terminals are not used on controller.
19
20
21
E18: Run the line voltage power wires into the power supply.
19: Connect the hot power wire to the black power supply wire
and black controller power supply wire with a wire nut.
20: Connect the neutral power wire to the white power supply
wire and white controller power supply wire with a wire
nut.
21: Make sure the green transformer wire is grounded in
accordance with local electrical codes.
14: Connect one end of a data wire (blue with white stripes
wire) to master LED driver "LEDSYNC OUT–" terminal.
Connect the other end into the DVR-RGB-60 "DMX in –"
terminal.
15: Connect one end of a data wire (white with blue stripes
wire) to master LED driver "LEDSYNC OUT+" terminal.
Connect the other end into the DVR-RGB-60 "DMX in +"
terminal.
16: Connect one end of a data wire (bare shield wire) to
to master LED driver"LEDSYNC SHIELD" terminal. Connect
the other end into the DVR-RGB-60 "DMX in shield"
terminal.
17: Repeat steps 14-16 for additional slave LED drivers.
NOTE: Use instructions below to wire master LED driver to
additional slave LED drivers.
M
Ext in-
Ext in+
DMX in +
DMX in -
DMX in shield
LedSync thru+
LedSync thru-
LedSync shield
Driver
M
Ext in-
Ext in+
DMX in +
DMX in -
DMX in shield
LedSync thru+
LedSync thru-
LedSync shield
Driver
VDC+
VDC-
VDC+
VDC-
D
DMX CABLE (BELDEN #9841)
MASTER LED
DRIVER
SLAVE LED
DRIVER
15
15
16
16
14
14
3
EXT in-
EXT in+
VDC-
VDC+
DMX in + DMX in - DMX in shield LEDSync out +
LEDSync out- LEDSync out shield
10
13
CONTROLLER
POWER SUPPLY
DVR-RGB-60
11
12
DO NOT
USE

E
LED SOFT STRIP
4
24
27
26
G
29: Replace the DVR-RGB-60 cover.
30: Replace the power supply cover and secure it by tightening
the six Phillips screws.
25
F
22: Use the "Low Voltage Wire Size Chart" on page 1 to
determine proper wire size connecting to the DVR-RGB-60
terminals.
23: Run the proper size green, red, blue, and black wires from
the RGB LED soft strip to the power supply enclosure.
24: Connect the black wire into the DVR-RBG-60 "LED
SUPPLY +" white terminal. Connect the other end to the
black wire(s) of the RGB soft strip.
25: Connect the red wire into the DVR-RBG-60 "Group 1-" red
terminal. Connect the other end to the red wire(s) of the
RGB soft strip.
26: Connect the green wire into the DVR-RBG-60 "Group 2-"
green terminal. Connect the other end to the green wire(s)
of the RGB soft strip.
27: Connect the blue wire into DVR-RGB-60 "Group 3-" blue
terminal. Connect the other end to the blue wire(s) of the
RGB soft strip.
28: Repeat steps 23-27 for additional DMX controllers and soft
strips.
NOTE: Do not exceed the maximum wattage of the power
supply.
NOTE: Use only 24 volt LED RGB soft strip with this power
supply.
NOTE: The DVR-RGB-60 terminals adapt maximum 18 AWG
size. To avoid voltage drop, use 6" of 18 AWG size in RGB
terminals connected inline to proper size gauge wire attached
to the RGB LED wires with wire nuts. See the "Low Voltage
Wire Size Chart" on page 1.
30

Operating CDP
1- Turn the light on 2- Change brightness 3- Turn the light off
BRIGHTNESS
Selecting Modes
O N
1 2 3 4 5 6 7
COLOR MODE
O N
1 2 3 4 5 6 7
Configure your CDP by setting the DIP switches on the front:
NOTE: The DIP switches must
remain accessible after installation.
When making changes in the DIP
switch settings, disconnect and
reconnect the power supply to
activate new settings.
CHASE MODE
TAP TAP
O N
1 2 3 4 5 6 7
31: Align the face plate to the controller and secure using the
two flat head screws.
32: Attach the push button onto the controller center rod and
secure by tightening the M3 set screw with the 1.5mm Allen
wrench provided.
HCONTROLLER FACE PLATE
FLAT HEAD
SCREW
PUSH
BUTTON
1.5MM ALLEN
WRENCH
27
28
5
Configuring and Operating Dim Wheel
1- Turn the light on 3- Set Color2- Activate configuration mode
2 SEC
4- Save color saving
Advanced Operation for Color Mode
TAP TAP

1- Turn the light on 3- Set Color2- Activate configuration mode
2 SEC
5- Set White
4- Activate White
6- Save settings
Advanced Operation for RGBW
TAP TAP
TAP
7- Dim
BRIGHTNESS
6
1- Turn the light on 3- Set show speed2- Activate configuration mode
2 SEC
4- Save color saving
Advanced Operation for Chase Mode
TAP TAP

7
DVR-RGB
M
Ext in- Ext in+ DMX in + DMX in - DMX in shield LedSync thru+ LedSync thru- LedSync shield
LED supply +
Group 1 - Group 2 - Group 3 - Group 4 -
Driver
VDC+
VDC-
Input Wiring Diagram for 2x100W (Shown)
M
Ext in- Ext in+ DMX in + DMX in - DMX in shield LedSync thru+ LedSync thru- LedSync shield
LED supply +
Group 1 - Group 2 - Group 3 - Group 4 -
Driver
(+)
VDC+
VDC-
24VDC
+ -
LINE
N L
(-)
(+)
(-)
24VDC
120VAC
L
L N N
120VAC 24VDC
(+)(-)
DMX CABLE
CTP
CDP
CDMX
DVR-RGB
S1 S2 S3
Power Supply Power Supply

8
Output RGB+W Wiring for 2x100W (Shown)
Output Tunable White Wiring Diagram for 2x100W (Shown)
Output RGB Wiring for 2x100W (Shown)
M
Ext in-
Ext in+
DMX in +
DMX in -
DMX in shield
LedSync thru+
LedSync thru-
LedSync shield
LED supply +
Group 1 -
Group 2 -
Group 3 -
Group 4 -
Driver
VDC+
VDC- 24VDC
DVR-RGB
RGB LED Soft Strip
M
Ext in-
Ext in+
DMX in +
DMX in -
DMX in shield
LedSync thru+
LedSync thru-
LedSync shield
LED supply +
Group 1 -
Group 2 -
Group 3 -
Group 4 -
Driver
VDC+
VDC- 24VDC
DVR-RGB
RGB LED Soft Strip
RGB + W LED Soft Strip
M
Ext in-
Ext in+
DMX in +
DMX in -
DMX in shield
LedSync thru+
LedSync thru-
LedSync shield
LED supply +
Group 1 -
Group 2 -
Group 3 -
Group 4 -
Driver
VDC+
VDC- 24VDC
DVR-RGB
RGB + W LED Soft Strip
M
Ext in-
Ext in+
DMX in +
DMX in -
DMX in shield
LedSync thru+
LedSync thru-
LedSync shield
LED supply +
Group 1 -
Group 2 -
Group 3 -
Group 4 -
Driver
VDC+
VDC- 24VDC
DVR-RGB
M
Ext in-
Ext in+
DMX in +
DMX in -
DMX in shield
LedSync thru+
LedSync thru-
LedSync shield
LED supply +
Group 1 -
Group 2 -
Group 3 -
Group 4 -
Driver
VDC+
VDC-
DVR-RGB
Tunable White (2K4K) LED Soft Strip
24VDC
M
Ext in-
Ext in+
DMX in +
DMX in -
DMX in shield
LedSync thru+
LedSync thru-
LedSync shield
LED supply +
Group 1 -
Group 2 -
Group 3 -
Group 4 -
Driver
VDC+
VDC-
DVR-RGB
Tunable White (2K4K) LED Soft Strip
24VDC