Pure Resonance Audio C3 User manual

INSTALLATION AND OPERATION MANUAL
Caution: Please read this manual carefully before operating.
Damage caused by misuse is not covered by the warranty.
C3 3” MICRO IN-CEILING LOUDSPEAKER

INTRODUCTION
DESCRIPTION
The Pure Resonance Audio C3 3" micro in-ceiling loudspeaker’s stylish design is compact and lightweight.
Featuring a 70 volt and 8-ohm tap, the C3 ceiling speaker is perfect for background music in commercial
environments. It is quick and easy to install with the screw on mounting ring.
FEATURES
�Compact and lightweight
�Smallest possible footprint while maintaining powerful quality sound
�Intelligent, stylish design that seamlessly blends into the ceiling
�Power tap transformer switch for selectable 8 ohm or 70V/100V operation for commercial applications
�Tap settings
• 70V: 8 ohm, 1.5W, 3W, 5W
• 100V: 8 ohm, 3W, 6W, 10W
�Quick & easy installation with threaded mounting ring
�Perfect for background music in offices, retail stores, restaurants, hotels, foyers, and auxiliary spaces
SPECIFICATIONS
Power Taps @ 100V
SPL (1W/1M)
Frequency Response
Dimensions (H x W x D)
Weight
3W/6W/10W
Power Taps @ 70V 1.5W/3W/5W
88dB
120 - 20KHz
5.12” (130 mm) x 5.12” (130 mm) x 3.94” (100 mm)
2.9 lbs (1.3 kg)
Impedance 8 Ohms with 70 Volt transformer (Built-in)
Cutout Size 4.33” (110 mm)

IMPORTANT SAFETY INSTRUCTIONS
***THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED TECHNICIAN.
THE PROVIDED INSTALLATION HARDWARE MUST BE USED TO INSTALL THIS PRODUCT.
SPEAKER UNIT MUST BE ATTACHED BY A SAFETY CABLE!***
Pro Acoustics is not responsible for the structural integrity of the installation. Please make sure a qualied
technician installs this product and the building’s engineer or architect has approved the equipment and
installation.
1. DO NOT block any ventilation openings. Install in accordance with all safety standards and regulations.
2. DO NOT allow any water exposure to speakers.
3. Ensure that no damage to speaker wire is present when installing. Frayed or unterminated wires can lead
to electrical or re danger. When preparing wires, make sure your amplier is turned o & unplugged.
4. AVOID instability in the installation or set up of speakers, to avoid personal injury or property damage.
5. Conrm area where speaker will be installed is structurally sound without signs of damage or structural
issues.
6. DO NOT plug in speaker while hands are wet. May lead to electric shock.
7. MAKE SURE to pull plugs, rather than pull wires. The use of strained or damaged speaker wire may cause
re or electric shock.
8. When connecting/disconnecting speakers, take care to remove the speaker connector without pulling
out the wires. Contact with bare wires when energized can lead to electrical shock.
9. AVOID installing speakers in humidity or dust, direct contact with the sun, near electric, smoke or steam.
May cause re or electric shock.
*WARNING: To prevent injury, this apparatus must be securely attached in accordance with the installation
instructions. No naked ame sources – such as candles – should be placed close to the product.
*CAUTION: Changes or modications not expressly approved by the manufacturer could void the user’s
warranty.
WARNING!
SAFETY PRECAUTIONS
�Be sure to read the instructions in this section carefully before use. The included conventions of safety
symbols and messages are regarded as very important precautions.
� We recommend you keep this instruction manual handy for future reference.
SAFETY SYMBOL AND MESSAGE CONVENTIONS
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating this product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety risks.
Indicates a potentially hazardous situation which, if mishandled, could result
in death or serious personal injury.
Indicates a potentially hazardous situation which, if mishandled, could result
in moderate or minor personal injury, and/or property damage.
WARNING!
CAUTION!

INSTALLATION & OPERATION GUIDE
SPEAKER PLACEMENT
�If you desire music over a wide area, it is best to have a larger number of speakers playing at low volume,
rather than a few speakers playing at high volume. Keep this in mind when designing your system.
�Ideally, you should place the speakers as close to the primary listening area as possible. The perceived
volume of the speaker decreases rapidly as it is moved further from the listener.
CONNECTING THE SPEAKER TO YOUR SYSTEM
1. The 4-pin Euroblock plug allows for speaker wire input as well as speaker wire output to easily daisy
chain speakers in 70V applications.
2. Determine the locations for the speakers and estimate the length of the additional wire you will need for
each speaker.
3. Connect the speaker wires from your amplifier to the in-ceiling speakers.
IMPORTANT: Be sure not to let any stray “+” and “-” strands touch each other. Touching strands can cause a
short circuit that could damage the amplifier.
4. Turn your amplifier on and test the system with your favorite music.
PLEASE NOTE:
Confirm that you have connected the speaker “+” to the amplifier “+” and the speaker “-” to the
amplifier “-”.
IN-CEILING MOUNTING
PLEASE NOTE:
Before beginning installation be sure to take precise measurements.
1. Select speaker location.
2. Run speaker wire to desired position.
3. Measure and cut your hole in the ceiling in desired position. If mounting into an acoustic tile ceiling, remove ceiling
tile when attaching the speaker.
4. Unpack the speaker unit with mounting ring.
5. Insert speaker into hole in the ceiling. Place threaded mounting ring on back of the speaker.
6. Rotate the mounting ring onto the ceiling speaker until it is tight.
PLEASE NOTE:
It is recommended to also attach the speaker unit using a safety cable. Cable and hardware not provided.
7. Run the speaker wire
8. Connect the speaker wire to (+) and (-) inputs. Use the extra (+) and (-) for daisy-chaining.
7. Select the desired tap setting.
9. Your speaker should now be securely installed.

SPEAKER INSTALLATION
DIMENSION
Step 1: Put the circle over the ceiling. Step 2: Rotate the ceiling speaker into the circle until it is tight.
Step 3: Finish installation.
130mm130mm
120mm
100mm
Step 1 Step 2 Step 3

BASIC SPEAKER INSTALLATION - 70 VOLT SYSTEMS AND APPLICATIONS
BASIC ATTENUATOR/VOLUME CONTROL INSTALLATION
Be careful not to cross wires when installing your speakers. Wiring should always be negative to negative
and positive to positive
(Figure 2. shows speaker c. incorrectly wired).
SPEAKER OUTPUT
COM 70V 100V
4Ω 8Ω 16Ω
+-+-+-+-+-
a. b. c.
Correct Speaker Wiring
Figure 1.
SPEAKER OUTPUT
COM 70V 100V
4Ω 8Ω 16Ω
+-+-+-+-+-
a. b. c.
Incorrect Speaker Wiring
Figure 2.
W
R
ONG
SPEAKER OUTPUT
COM 70V 100V
4Ω 8Ω 16Ω
a. b. c.
ATT IN
SPK OUT
Full Remote Control Attenuation
Figure 3.
+-
+-
+-
+-
+-
SPEAKER OUTPUT
COM 70V 100V
4Ω 8Ω 16Ω
ATT IN SPK OUT
Zone Remote Control Attenuation
Figure 4.
a. b. c.
+-
+-
+-
+-
+-

SERVICE
Ensure the problem is not related to operator error, or system devices that are external to this unit. Informa-
tion provided in the troubleshooting portion of this manual may help with this process. Once it is certain that
the problem is related to the product contact your warranty provider as described in the warranty section of
this manual.
LIMITED WARRANTY
PRO ACOUSTICS, LLC. ("PRO ACOUSTICS") warrants this product to the original purchaser to be free from
defects in materials and workmanship (subject to the terms set forth below), for the following periods from
the date of purchase.
THIS WARRANTY COVERS THE LISTED PRODUCTS AGAINST DEFECTS IN MATERIALS OR
WORKMANSHIP FOR THE FOLLOWING PERIOD
Warranty Terms
PRO ACOUSTICS will repair or replace (at PRO ACOUSTICS's option) this product or any defective parts
(excluding electronics and amplifiers) in this product.
Your authorized PRO ACOUSTICS dealer will inspect the product and, if your dealer is not equipped to
perform the repair of your PRO ACOUSTICS product, they will replace your product or return it to PRO
ACOUSTICS for repair, at their discretion. Proof of purchase in the form of a bill of sale or receipted invoice,
which is evidence that this product is within the warranty period, must be presented to obtain warranty
service.
This warranty is invalid if the factory applied serial number has been altered or removed from this product.
This warranty is invalid if this product was not purchased from a PRO ACOUSTICS authorized dealer. Cos-
metic damage or damage due to the accident, acts of God, misuse, abuse, negligence, commercial use, or
modification of, or to any part of, the product are not covered in this warranty. This warranty does not cover
damage due to improper operation, maintenance or installation, or attempted repair by anyone other than
PRO ACOUSTICS or a PRO ACOUSTICS dealer which is authorized to do PRO ACOUSTICS warranty work.
Any unauthorized repairs will void this warranty.
This warranty does not cover products sold as is.
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF
THE CONSUMER/PURCHASER. PRO ACOUSTICS U.S.A. SHALL NOT BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU
OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER, INCLUDING BUT NOT LIMITED TO,
THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE.
This warranty gives you specific legal rights. You may have other rights which vary from state to state.
Speakers
Amplifiers & Electronics
Microphones
Accessories
2 Years
1 Year
1Year
1Year

PURE RESONANCE AUDIO
[phone]
[e-mail]
www.PureResonanceAudio.com
Specifications may change without notice.