Pyle PLCD51BT User manual

-1-
Content
Installation steps...........................................................................
General information about remote control......................................
1. Removing insulating sheet.........................................................
2. Replacing the lithium cell...........................................................
3. Note about using the remote control...........................................
4. Warning about lithium cells of remote control.............................
Locations and Names of controls...................................................
1. Locations and Names of controls on main unit............................
2. Locations and Names of controls on remote control...................
General operation...........................................................................
Radio operation.............................................................................
BT operation..................................................................................
Disc/USB/card operation............ ...................................................
1. Loading or unloading a disc, USB or card..................................
1.1 Loading a disc, USB or card.....................................................
1.2 Unloading a disc, USB or card..................................................
2. Function of controls on main unit or remote control..................
AUX IN operation...........................................................................
Troubleshooting............................................................................
Specifications...............................................................................
2
6
6
6
6
6
7
7
8
9
10
12
14
14
14
14
15
17
18
19

INSTALLATION STEPS
1. Remove 2 screws for protecting deck;
1) Remove chassis from the Slide Bracket Housing as follows:
2) Remove 2 screws protecting the deck as
right;
2. Connecting all wires
1) Slide Bracket Housing;
2) Remove the control panel from the chassis as follows:
A. Press REL button to detach the control panel .
B. Hold the right end of the control panel to pull rightward
illustrated on the
Re-insert the chassis into the
a little and then remove it
REL button
PLASTIC TRIM OUT
KEY PLATE
KEY PLATE
If you want to remove the chassis from the Slide Bracket Housing , first remove the
Plastic trim from both sides, then insert 2 Key Plates into the left and the right side of
the chassis as illustrated.
-2-

-3-
3) Connecting all wires as bellows:
IGNITION SWITCH
RED
WHITE
WHITE/BLACK
GREY
GREY/BLACK
GREEN
GREEN/BLACK
VIOLET
VIOLET/BLACK
YELLOW
CONSTANT 12 VOLTS
BLACK GROUND(B-)
BLUE AUTO ANTENNA
FRONT
Lch SPK.
REAR
Lch SPK.
FRONT
Rch SPK.
REAR
Rch SPK.
RADIO ANTENNA JACK
FRONT AUDIO OUT RCA JACK R (red)
FRONT AUDIO OUT RCA JACK L (white)
REAR AUDIO OUT RCA JACK L (white)
REAR AUDIO OUT RCA JACK R (red)
NOTE:
1. Must use 4 ohms impedance of speakers.
2. Before finishing wiring, do not attach control panel onto chassis.
3. Maximum current of auto antenna is 200mA.
ISO CONNECTOR
FUSE
FUSE

4) Attaching the control panel onto the chassis.
A. Align and thrush the bulge of the control panel into the hollow of the chassis.
B. Push the right end of the control panel to the chassis till a click sound is heard.
* How to clean panel connector
Frequent detachment will cause the panel connectors to deteriorate. To minimize
deterioration, periodically wipe the panel connector with a clean/soft/dry cloth .
5) Test to make sure that it works properly.
3. Instal the main unit according to the installation diagram on the next page:
1) Mount the main unit in A/V position in vehicle.
2) Bend tabs of the sliding metal housing where necessary to ensure that
the front part of main unit is fixed;
3) Use a metal strap to fix the rear part of the chassis.
* Uninstalling the main unit:
1) Remove the metal strap from the main unit;
2) Remove the plastic trim frame from the main unit;
3) Insert a key plate into the left and the right side of the main unit and draw the
main unit out of the sliding metal housing.
Bulge
Hollow
Panel Connector
-4-

-5-
Installation diagram
DASH BOARD
METAL MOUNTING
STRAP
HEX NUT
SPRING WASHER
PLAIN WASHER
TAPPING SCREW
CONSOLE
SLIDE BRACKET
HOUSING
HEX BOLT

-6-
General information about the remote control
1. Removing insulating sheet
The remote control comes with an insulating
sheet attached to the underside of the remote
control as illustrated on the right
The remote control is disabled and will not work
until the insulating sheet is removed.
as illustrated on the right
.
2. Replacing the lithium cell
If the electric energy of the lithium cell is weak,
replace it .
1. Press and hold the movable block in the
direction indicated by arrow 1 , at the same
time pull the cell holder out of the remote control
in the direction indicated by arrow 2 .
2. Replace the old cell with a new one with (+)
polarity side upward .
3. Insert the cell holder into the remote control again.
3. Note about using the remote control
1. Face the emitting window of the remote control towards the sensor window of
the unit.
2. Operation angle for front panel: About 30 degrees
3. The distance between the emitting window of the remote control and the sensor
window of the unit : < 5M .
4. Warning for lithium cells of remote control
leakage may cause damage to remote control.1.Cell
2.Do not throw cells into fire, it may cause an explosion.
3.To avoid accidents, keep cells out of reach of children.

Locations and Names of controls
1. Locations and Names of controls on main unit
-7-
1823
1. REL button
2. PWR or MODE button
3. SEL button and VOL knob
4. BAND or ID3 or button
5. TA or AF button
6. APS button
7. MUTE or PTY button
8. >|| or 1 button
9. INT or 2 button
10.RPT or 3 button
11.RDM or 4 button
12.-10 or 5 button
13.+10 or 6 button
14. |<< button
15. >>| button
16. PAIR or button
17. EJECT button
18. RESET button
19. IR sensor window
20. AUX IN jack
21. USB port
22. LCD screen
23. Card slot
24. CLK button
25. Disc slot
Control Panel
Front side of chassis after removing control panel
2
31
7
6
9814
15 17 19
20
21
22
25
4510 11 12 13
16
24

2. Locations and Names of controls on remote control
-8-
1
2
3
5
6
8
9
11
4
7
10
12
13
14
15
16
17
18
19
20
21
1. PWR button
2. < button
3. button
4. VOL- button
5. >|| or TOP or 1 button
6. RDM or 4 button
7. -10 or 5 button
8. 7 or TA button
9. DISP or * button
10. 8 or AF button
11. VOL+ button
12. MUTE or MODE button
13. SEL or ENTER button
14. > button
15. button
16. RPT or 3 button
17. INT or 2 button
18. +10 or 6 button
19. 9 or PTY button
20. SCAN or # button
21. BAND or ID3 or 0 button
NCA -608AA
TA AF PTY

General Operation
1. PWR button
To power main unit on , short press the PWR button on the control panel or on the
remote control .
To power main unit off, long press the PWR button on the control panel or short
press the PWR button on the remote control .
2. VOL knob or VOL+ & VOL- button
To increase or decrease volume level.
3. MUTE button
To cancel or resume sound, long press the MUTE button on the control panel or
long press the MUTE button on the remote control .
4. SEL button
5. DISP or CLK button
To display clock time, briefly press the CLK button on control panel or short press
the DISP button on remote control .
To set clock time, first long press the CLK button to flash hour, and rotate the VOL
knob or press the VOL+ or VOL- button to adjust the hour; then briefly press the
SEL button to flash minute, and rotate the VOL knob or press the VOL+ or VOL-
button to adjust the minutes; finally press the CLK button to confirm it.
6. MODE button
To switch on a work source between RADIO, DISC, USB, CARD, AUX IN and BT
AUDIO(after pairing and connecting). repeatedly press the MODE button on the c
ontrol panel or on the remote control.
7. REL button
To detach the control panel from chassis.
8. RESET button
To reset all parameters to factory default values.
* When LCD does not display normally or sound is distorted or some controls are
disabled, press the REL button to detach the control panel from chassis and re-
move the control panel from the chassis, then use a subject with a sharp point
end to thrush the RESET hole.
To switch between VOL(volume), BAS(bass), TRE(treble), BAL(balance), FAD
(fader), EQ, BEEP, LOUD, MONO/STEREO(in radio mode) , LOC/DX(in radio
mode) and BT, press the SEL button repeatedly. After selecting a desired mode,
rotate the VOL knob or press the VOL+ or VOL- button to set it.
To switch between TA SEEK/ALAR, MASK AL/DP, RETUNE S/L and TA VOL 25,
long press the SEL button to switch on TA SEEK/ALAR, then short and repeatedly
press the SEL button. After selecting a desired mode, rotate the VOL knob or
press the VOL+ or VOL- button to set it.
-9-