Pyle PLR18MPF User manual

www.pyleaudio.com
PLRIBMPF
I.Control Panel
1I.0peration
1.Next button
1. Next button
2. Play/Pause button
3. Volume knob
4. Display
5.Time controls
6. Auto scan button
7.Tunerknob
8. Prevo button
9. Power switch
10. SD / MMC card slot
11 . USB interface
12.
Mode switch
13.
Band button
In USB/SD/MMC playing state, press this button to
select and play nexttrack, or press
and hold this button to select and play +10 lattertracks.
In radio state, press this
buttonto select and play next channel.
2.Play/Pause button
In USB
or SD/MMC playing state, press this button to pause and press it again to
resume playing.
In radio state, select desired channel with the tuner knob and press
this button to save the channel (up to 18 channels can be saved).
3.volume knob
Rotate this knob to adjust the volume.
4.Display
Display radio frequency
or playing info.
5.Time controls
To adjust the hour, press and hold the H key, and then press the H key to adjust the
value when the hourvalue flashes; to
adjust the minute, press and hold the M key, and
then press the M key to
adjust the value when the minute value flashes. After adjus
tment,
wait for several seconds and the radio or playing status barwill resume.
6.Auto scan button
In radio state, press and hold this button to scan and store channel automatically until
the three
FM bands are saved completely. Press and hold this key to view the saved
1.

Channels. When the signal from desire channel is received, press this button again to
listen to the program.
7.Tuner knob
In radio state, rotate the knob to left/right to scan radio channels automatically or
manually.
8.Prev. button
In USB/SD/MMC playing state, press this button to select and play previous track, or
press and hold it to select and play -1 0 previous tracks. In radio state, press this button
to
select and play previous channel.
9.Power switch
Press this button to turn on the device and press it again to turn off.
10.SD/MMC card
slot
InsertSD/MMC card and play the tracks automatically.
11.USB interface
Insert USD
disk and play the tracks automatically.
12.Mode switch
Press the MOD button to switch mode.
If USB disk and SD/MMC card are connected to
the device, press the MOD button to switch in this sequence: USB, SD/MMC, radio;
if only USB disk or SD/MMC card is connected, press the MOD button to switch between
available modes;
if both USB disk and SD/MMC card are not connected, MOD button is
invalid.
13.Band button
In radio state, press this button to select the band.
III.Technical parameters
FMTUNER
Tu ning ra ng e: -- -----------------------------------------------------------------8 7.5MHz -1 08MHz
Intermediate frequency: ------------------------------------------------------------------10. 7M Hz
SNR: --------------------------------------------------------------------------------------------=50dB
AMTUNER
Tu ning range -------------------------------------------------------------------------530-171OKHz
Usab
lese nsitivity ------------------------------------------------------------------------------ 38dB
Playing:
SNR: ------------------------------------------------------------------------------------------- ;:, 50dB
Channel isolation(at 1 kHz):--------------------------------------------------------------- ;:, 23dB
Harmonic distortion (at 1 kHz):
-------------------------------------------------------------- :::; 5%
Frequency response:
-----------------------------------------------------( 100 Hz-10kHz) ±6dB
Power amplifier:
Output:------------------------------------------------------------------------------- Speaker 0 utput
Speake rim pedance: ------------------------------------------------------------------------4 Q--8Q
Maximum output power: -----------------------------------------------------5OWX4(200Watts)
Power
supply:--------------------------------------------------------------- 12VDC car batteries
IV.lnstaliation diagram
1.Before installing the master unit, put it in the proper position, and connect the speaker
wire and powercord.
2.1f the masterunit runs normally, fix it.
2.

Fixing flake
\
Stand
- Double-head screw
/ /
Disassembly key
IInstalling the masterunit
~
1.lnstall the bracket on the dashboard of the vehicle, and bend the stand.
2.Connect the power cord and speakerwire, and fix the fixing flake on the vehicle.
3.lnsert the antenna plug, push the masterunit into the stand and fasten the fixing nuts.
LUninstaliing the masterunit
Remove the fixing nuts, insertthe two disassembly keys into the gaps on the left and
right sides, hookthe master unit with the keys and pull out lightly. Then, pull
out the
antenna plug and remove the power cord and speakerwire.
V.Wiring diagram
To Automatic Blue
Antenna _"":::=_...J
Left
Speaker
Left
Speaker
+ White
_Whitewith
black strip
+ Green
_ Green with
black strip
3.
Black
To Battery +
To Ignition
Switch
'-- ____ To Battery-
Grey +
Grey with-
black strip
Violet +
Violet with -
black strip
Right
Speaker
Right
Speaker

VI.Precautions
Only replace the fuses ofsame specification.
VII.Troubleshooting
Failure Reason Solution
Can't start thedevice
The fuse is melt
Replace with same fuse
No memory
Ignition wire and anode power
Reconnect the wire.
cord are not connected properly
The vehicle antenna isn't
Check whether the control wire
of automatic radio antenna is
Weak radio signal
stretched out ,
connected properly; check
Poor antenna grounding
whether antenna and ground
wire are connected properly
Can't read SO card
SO card is inserted reversely
or damaged
Turn over or replace the SO card
The connection is improper
Check and correct the connection
No audio or lowvolume
Speaker is connected to ground
Connect the speaker to the
cathode of power amplifier output
Note: The specifications are subject to changes without prior notice.
4.