MAIN CONTROL
1
2
3
4
5
6
8
7
3
7 8 95 6
1
4
2
1
2
8. [FX] Controller, adjust the signal level from the channel to the reverberation line. Please note, the single level
will vary with the different setting of the channel attenuator. If using the stereo channel, will mix the signals
from L and R channels, then, send it to reverberation line.
9. [PEAK] LED indicator light, when the volume of input signal or volume after adjusting equalizer is too high, the
LED indicator light will keep flashing, please rotate the[GAIN] CONTROLLER counterclockwise to turn down
the volume.
1. The external power input socket, receiving external power supply, DC +15V, -15V, +48V, ground wire
2. Power Switch
[PROGRAM] Controller, select from 16 kinds of internal digital
effects, provide the same signal to L and R stereo.
[REPEAT] Echo controller of internal effects, adjust to achieve the
desired state of internal echo signal.
[FX LEVEL] Effects return level controller, adjust the volume of
effect.
Level indicators can show the signal level from [STEREO OUT]
output. Adjust the [LEVEL] controller to lower the level if [PEAK]
indicator light up in RED.
[LEVEL PHONES] Earphone controller, adjust the volume of
earphone.
[STEREO LEVEL] Fader, adjust the overall volume from
[STEREO OUT] output signal.
[SEND] Level controller, adjust the sending level.
[RETURN] Level controller, adjust the return level.
1.
2.
3.
4.
5.
6.
7.
8.
1. USB interface, use for MP3 input or computer
connection (can be used for U disk or computer
software recording)
2. MP3 Display, displays the status and details of the
MP3 play.
3. [MAIN OUT] Output, connect the active speaker or
amplifier.
4. [CTRL OUT] Output, connect the monitor room to
monitor.
5. [+48V PHANTOM] Button/LED, when the button is
turned on, the LED light is on, provide Please turn on
this button when using the c ondenser microphone
which is powered by a phantom power.
6. Converting switch for channel 3/4 and USB signal .
7. Channel input socket (stereo), 8CH mixer with two group of input socket, 4CH and 6CH mixers with one group of
input socket. If only connect to L (MONO) socket, the mixer will send out the same mono signal to L and R sockets.
8. [SEND & RETURN] Socket, when using the [SEND] output socket separately, can be connected with power
amplifier, act as the monitoring signal. When using the [RETURN] input socket separately, can be connected
with the audio source. When using two sockets together, can connect with the external audio processor.
9. [PHONES] Socket, connect an earphone, the socket is supporting stereo phone plug.
CHANNEL INPUT
1
2
3
4
5
6
7
8
9
10
● Built-in 16 bit DSP processor
● Built-in Bluetooth connect with mobile phone or other Bluetooth Player
● Built-in MP3 player support a variety of music formats
● Connect the computer to record and play music
1. 4/6/8 channels mixer
2. Mic + stereo line inputs
3. Ultra-musical 3-band EQ on all channels
4. Peak LED on all Channels
5. High accurate level indicator
6. Phantom power switch (+48V)
7. Sealed rotary controls to resist dust and grime
8. Rugged steel chassis
9. New Multi-Voltage power supply for worldwide use
1. [MIC/LINE] Mono input, connect the microphone, musical instrument or audio device
(CD player and so on) to the device. The sockets are supporting both XLR and
UNBALANCED 1/4" PLUG.
[+48V PHANTOM] Button/LED, when the button is turned on, the LED light is on,
provide DC+48V phantom power to XLR plug on MIC/LINE mono input.Please turn on
this button when using the condenser microphone which is powered by a phantom
power.
[PAD] button, it will attenuate the sound input to the device when turn on this switch. You
can turn on the switch if you hear the distortion or [PEAK]LED indicator light is on.
[GAIN] Controller, determines the basic volume of each channel, adjust them for the
maximum volume performance, when the volume gets too loud, the [PEAK]LED
indicator light will keep
[HIGH] Treble tone controller, adjust the controller to enhance or attenuate for 15dB at
12KHz.
[MID] Alto tone controller, adjust the controller to enhance or attenuate for 15dB at
2.5KHz.
[LOW] Bass tone controller, adjust the controller to enhance or attenuate for 15dB at
80Hz.
XLR UNBALANCED 1/4 " PLUG
2.
3.
4.
5.
7.
6.
4 CHANNEL 6 CHANNEL8 CHANNEL
1. 2.
