Pyramid Time Systems Timetrax EZ Prox ek PPDLAUBKN User manual

Quick Start Guide
Proximity Time Clock System
PPDLAUBKN

What you will need.
Tape Measure Pencil Phillips Head
Screw Driver
Power Drill
(Optional)
TTEZPROXEK
Terminal
TimeTrax™
Proximity Badges (15)
Part #42454
TIMETRAX™
Software CD
Ethernet
Cable
(CAT5)
Mounting
Hardware
TTPROXEK Quick Start
Guide &
TTEZ Series Software
Reference Guide
Power
Supply Security Bracket
& Key
Contents
Quick Start Guide
pyramidtimesystems.com
pyramidtimesystems.com
MODELS TTEZ, TTEZEK, TTEZPROXEK (PPDLAUBKN)
Software Reference Guide

IMPORTANT:
Please write down serial #
located on back of terminal
before mounting.
Write your serial # here:

SAMPLE
Software Requirements
Single User installation,
Local Area Network (LAN) only
TimeTrax™ Time & Attendance software does
not operate on server PC’s. Pyramid Time
Systems does not support the use of TimeTrax™
software on a server PC.
DHCP enabled network
Windows XP, Vista, 7 or 8
Regional settings & hardware
input in English
DHCP
English
TM

Connect & Mount Terminal
Connect Ethernet cable into Ethernet
port located in compartment on back
of terminal.
Connect power supply into power port
located in compartment on back of
terminal.
Route the cables through channel at base
of terminal.
Mount terminal (see instructions below).
Plug free end of Ethernet cable into
network jack, router or switch.
Plug free end of power supply into
outlet.
1
2
3
4
5
6
1
To mount terminal.

bottom of bracket should be approximately 45
 Level bracket & mark four screw holes close to
corner tabs.
 Drill holes as marked and insert included anchors
if needed.
 Screw mounting bracket to wall with included
screws.
 Drill hole centered in rectangular opening of
bracket for cables. The hole should be large
enough to route cables through wall.
 Push terminal onto mounting bracket aligning
four tabs on bracket with four matching slots on
back of terminal.
 Slide terminal downward until locking tab clicks
into place. When properly mounted, terminal
cannot be slid up and off bracket without using
included wall bracket release key to disengage
locking tab.
To detach terminal.
 Hold included wall bracket release key with
pointed end up & diagonally cut side away from
you.
 Insert key into narrow slot located on bottom of
terminal to right of cable access cutout.
 Push key all the way up into slot. Key will slide
easily until last ½ inch until some resistance from
locking tab is felt.
 With key fully pushed into slot, slide the terminal
up and off mounting bracket.
4
2
3
5 6
1

Install TimeTrax™ EZ Software
Insert TimeTrax™ CD into CD-ROM drive.
Enter temporary User Name “ADMIN”.
Enter temporary password “PTI”
(case sensitive). Click “Login”.
Click “Finish” when install is complete.
Click on Pyramid TimeTraxTM desktop
icon.
Click “Yes/Unblock” to allow program
to make changes to this computer.
“Recorder Found” message will appear.
Click “OK” to continue. If “No Recorder
Found” message appears, check cable
connections and click “Reconnect”.
TimeTrax™ EZ InstallAware Wizard will
automatically open. Click “Next” to
begin install.
1
3
5
4
6
  
2

Click “Yes” to continue.
Payroll Setup
5
*Choose Pay Period format, start day, and start
time. Click “Save” then click “Setup Pay
Categories” to continue.

* Start time should be one hour after last Out punch of previous pay period and
rt at 12 midnight.
Choose “Yes” to continue to
Payroll SetUp screen.
3
12
4
Click “Edit” to set up pay period.
Click “Edit” to edit any of the

Employee Setup
Click “Edit” to begin. Enter Daily and
Weekly Overtime. 1Choose “Advanced”
for additional Employee Group settings.
Wave prox badge within two inches of target area.
If employee badge number is successfully read,
the time clock terminal will beep and the badge
screen.
Employee records generated from prox badge
punches are stored within the terminal. The ter-
minal stores the last 6,000 punches before down-
load is required. Depending upon usage, punches
can be retrieved on a more or less frequent basis.
Click “Add” to enter a new employee.
Enter prox badge number in the Card 1
Click “Save” after entering each employee
or click “Cancel” to discard changes.
1

2
Using Time Clock
Please refer to Software Reference Guide for Advanced Employee Group Setup.

Copyright © 2015 Pyramid Time Systems. All rights reserved.
I2231 Rev. C
Call us
888.479.7264
Send us an email
[email protected]
Chat online
pyramidtimesystems.com