Qazqa Scout WL Dark Grey User manual

2 Y E A R S
G U A R A N T E E
Unchangeable LED
Scout WL Dark Grey
92301
Max.6x0.5W LED
3000K±300K
10000H
3.7V
1800mAh
LI-ION
Rechargeable
battery
III
INSTRUCTION MANUAL
1
2
1 2
φ6mm
30mm
3
57
7 M4 M
appro.90°
1.8-2.5m
10.1cm
14.3cm
12.1cm
75°
13.5cm
6
AUTO
ST4x30mm
4
8
ST4x30mm
6x 6x
6X27
0
IP44
█HOW TO DETERMINE WHERE TO MOUNT YOUR SOLAR PIR SENSOR LIGHT
The most important thing to remember for the operation of your SOLAR PIR SENSOR LIGHT is that
it works from the power contained in DIRECT SUNLIGHT. The more direct sunlight the solar cell
receives in a day, the longer the light will operate.
■Main Unit:
The main unit contains 6*0.5W LED, motion sensor and battery (3.7V 1800mAh LI-ION
Rechargeable battery). When deciding where to mount this unit, keep in mind that the motion
sensor that actives the light has a “eld of vision” of min. 7 meters (in front of the light) and about
90º (horizontal) at 25℃environmental temperature.
■Solar Cell:
The solar cell is the power source for the SOLAR PIR SENSOR LIGHT. It converts the sun’s energy
into electricity that charges the battery stored in main unit. This requires DIRECT SUNLIGHT
falling onto the face of solar cell for as long as possible over the course of day.
█ CLEANING
It is important that the solar panel is kept free of dirt and debris. A dirty solar panel will not allow
the battery to fully charge and this will shorten the life of battery and cause the light to malfunction
Important: Please ensure that you charge the solar lights in maximum sunlight for a
period of up to 3 days (for 1800mAh Li Battery) before switching on the lights, in order that
the lights work on a full charge

Scout WL Dark Grey
92301
INSTRUCTION MANUAL
█INSTALLATION STEPS
1. Press under the Wall mounting plate then pull out the main body.
2. Use the Wall mounting plate to mark the position of screw holes onto mounting surface.
4. Drill the wall to depth of about 30 mm and t the plastic plugs.
5. Fix the Wall mounting plate to the mounting surface with rightly screws. Care should be taken to
avoid drilling or screwing into concealed electrical wiring.
6. Turn the switch to “AUTO” position
7. Mounting the Main unit onto the Wall mounting plate.
8. Screw the rightly screw (supplied) under the main unit.
█FINAL ADJUSTMENT AND START-UP
After you successfully installed your SOLAR PIR SENSOR LIGHT,
you are almost ready for carefree operation with a few nal steps:
Initial 3-days Charge:
On the main unit there is a dial switch with 2 positions: ●OFF ●AUTO
AUTO —
Position for normal operation of unit.
OFF ---
1) Position for shipping or extended periods of non-use
2) Position for initial 3-day charge before nal adjustment and rst use. (Although the unit can
charge, it is not operational in this mode)
For now, turn the dial switch to OFF position. In this position the solar cell will charge the battery
without activating the unit. Leave the switch in this position for 3 sunny days to ensure that the battery
has a full charge prior to motion sensor adjustment and normal operation.
█Walking-test:
Point the motion sensor to face the area you want to detect motion in.
At night, walking slowly in its detection area, the sensor can detects moving invisible infra-red radiation
given off by a human body and then turn on the light. Test the coverage of the area by walking slowly
around until not to switch on the light.
█STORAGE
If you wish to store your light indoors for more than two or three days, follow these steps to prevent
damage to battery:
1. Turn the switch to OFF position
2. Store the light and solar panel where it can receive some sunlight or room light each day.
The battery needs light to maintain a charge during storage
█NOTE THE FOLLOWING TROUBLE-
SHOOTING:
1. Symptom: Light won’t activate in normal operation.
Correction:
The main unit switch is the AUTO position.
The motion sensor is positioned to face oncoming movement
Change the battery
2. Symptom: Light turns on during the day.
Correction: Make sure that
■ The unit mustn’t in shadow area.
3. Symptom: Light is not as bright as normal.
Correction:
■ Change the battery.
■
■
■