Qomo QPC30 User manual

1
PRECAUTIONS
Please follow these precautions:
To prevent fire or shock hazard, do not expose the unit to rain or
moisture.
To prevent electrical shock, do not open the unit. Refer to qualified
personnel for service only.
Do not use the unit continuously for more than 24 hours with camera
auto focus on. It may cause damage to the camera lens.
Be careful not to spill water or other liquids onto the unit, or allow
combustible or metallic objects to get inside the base.
Unplug the visualizer from the wall outlet when it is not being
used for a long period of time.
Clean the unit with a soft cloth lightly moistened with a mild
detergent solution.
Clean the lens carefully with an air spray or soft dry cloth to avoid
scratching it.
Rotatethe camera lens cap before powering the unit on.

2
Contents
Product Introduction.................................................. 3
Parts Identification..................................................... 3
Making Adjustments .................................................. 4
Control Panel.............................................................. 8
Remote Control Instruction....................................... 9
Installing Visualizer Software ................................. 11
USB PORT................................................................. 11
USB Image Capture.................................................. 12
Specification............................................................. 13

3
Product Introduction
Thank you for purchasing the QPC30 visualizer. This visualizer comes with a
new design which is more simple, flexible, portable and with a higher
resolution then previously. The visualizer can be used to present 3D objects,
texts, graphs, transparencies and negative films. It can be connected to a
projector, PC and other multi-media equipment. The visualizer is not just
equipment for the corporate environment but also an indispensable tool to
academic, medical and scientific communities.
Parts Identification

4
Making Adjustments
There are six places on the visualizer where it can be adjusted.
1. Adjust Mechanical Arm
This adjustment can increase and decrease an image. Holding the
visualizer base with one hand, adjust the mechanical arm with another
hand up and down. The mechanical arm can be moved from almost any
angle.

5
2. Adjust LED light
The LED light can be rotated 90 degrees. (as demonstrated below)
3. Adjust Camera Box
Hold the camera box and rotate it up and down. The camera box can be
rotated 45 degrees. (as demonstrated below)

6
Hold the camera box and rotate it left and right. The camera box can be
rotated 90 degrees. (as demonstrated below)
4. Adjust Camera Head
Hold the camera connector with one hand, and rotate the camera box
connector with another hand. The camera head can be rotated 90 degrees.
(as demonstrated below)

7
5. Adjust Base Bracket
Hold the visualizer base with one hand, and rotate the base bracket with
another hand. The base bracket can be rotated 45 degrees. (as
demonstrated below)
Notice: Do not rotate the parts emphatically when the rotation
reaches its maximum.

8
Control Panel
There are four touch buttons located on the top of the visualizer base:
·
+
T: Enlarge image
·
W
:Reduce image
·LED Light：Turn the LED light on/off
·Power: Turn the visualizer on/off
·Pilot Light: During normal operations, a blue light will be lit. In standby
mode, a red light will be lit.

9
Remote Control Instruction
POWER (Switch the visualizer On/Off)
SAVE (Save captured images)
RECALL (Multiple Screen Display)
LAMP (Control the arm lights)
ROTATE (Rotate the image)
FREEZE (Freeze the image)
NEG (Display film negatives)
MIRROR (V-Reverse the image)
XGA (Switch between XGA (1024 x 768) and SXGA (1280 x 1024) mode)
TEXT (Switch between image/text mode)
B&W (Switch between Color mode and Black & White mode)
TITLE (Freeze the top 1/8 of the screen)

10
SPLIT (Image Split function)
PROJECTOR POWER (No function)
PROJECTOR INPUT (No function)
EXIT (Exit selected function)
TELE/
W
IDE (Increase and decrease magnification)
FAR/NEAR (Focus near or far)
AUTO (To auto adjust brightness, auto white balance and auto focus)
CAM/PC1/PC2 (No function)
S-VIDEO/VIDEO (No function)
VOLUME+/- (No function)
RED+/- (Increase or decrease the red hue)
BLUE+/- (Increase or decrease the blue hue)
BRIGHT+/- (Increase or decrease the brightness)
SCROLL /(No function)