Qtex HFOC-100A User manual

HFOC-100A
User’s Manual
HDMI 2.0 Fiber Optic Active Armoured Cable
System requirements
- Check Source and Display parameters to meet the maximum resolution and standard
compatibility of the Product.
- Do not apply extra force or bend cable over its minimal radius.
- Since HFOC-100A uses Hybrid Technology, it does not provide galvanic isolation
between Source and Display interface ports (same as generic copper cable). Avoid
to install active hybrid cables when system has a ground loops issues or dierent line
power phase used at Source and Display installation points. It could result in failures
and electrical damages of connected equipment interfaces.
- No external power supply is needed, HFOC-100A is designed to use +5V internal
power supplied through the Source HDMI port.
- Do not use any intermediate cables or adapters between Source and Display ports
and the cable connectors.
- Do not connect or disconnect cable while Source and Display Devices are powered
On.
Installation
STEP 1 Carefully unpack the contents of the shipping group.
STEP 2 Twist the front and rear cover, distinguish both ends internal connectors.
STEP 3 Power O all devices.
STEP 4 Plug ‘Source’ labeled connector directly to the HDMI output interface of
the Source device (Blu-Ray, Media player, PC or laptop).
STEP 5 Plug ‘Display’ labeled connector directly to the HDMI input interface of the
Display device (Monitor, Projector or Videowall).
STEP 6 Power On the Display device, then Source Device.
STEP 7 Check and correct resolutions settings at Source Device according Display
if needed.
STEP 8 Enjoy Clear and High Resolution Picture.
Qtex HFOC-100A cables series designed to meet extremely high requirements of
modern audio-visual systems with harsh environments. Cables can support up to Ultra
HD 4K resolutions, 4:4:4 color sub-sampling along with multichannel audio include
ARC feature.
HFOC-100A supports throughout transmission of EDID signals from a display to
source device and compatible with HDCP encrypted signals. Two miniature converter
boards integrated into the HDMI interface connectors at both cable ends, covered by
protective caps.
HFOC-100A is designed for maximum protection from mechanical damaging with
helical steel tape armoring, at the same time polyurethane jacket and aramid ber
give good ame retardant eect. Additionaly it gives good protection for cable when
pulling it. The installation is simple as for a general copper HDMI cable. Thanks to its
design and hybrid technology, Qtex HFOC-100A cables do not require external power
supply and should be powered directly by the HDMI interface of the source device.
Cables are premade at dierent lengths from 5 to 100 meters long.
© 2021 Qtex Corporation. All Rights Reserved
Revision 1.0K Dec 2021

Product View & Dimensions (mm)
Product Specifications:
• Product type: Active Fiber Optic Cable
• Complies with HDMI 2.0 Specications
• Supports resolutions up to 4096x2160 pixel at 60Hz
• Supports color sub-sampling RGB/YUV 4:4:4
• Supports CEC, EDID, HDCP1.4/2.2 signals transmission
• Hybrid structure: 4x OM3 ber cores with 7x 30AWG copper wires
• Helical steel tape armoring, SUS 304 0.3mm
• Aramid ber, decitex 2000D, ame retardant
• Round Cable TPU jacket, ame, ultraviolet, acid, alkali and oil retardant, Color Black
• The maximum cable length is 100 meters
• High quality connectors with gold plated pins
• Powered by HDMI source (up to 200mA) without external power supply
• Maximum tensile load: 200N
• Minimum bending radius: 20mm
Environmental Specifications:
• Operating temperature: 0°C to 50°C
• Storage temperature: - 20°C to 70°C
• Humidity: 10% to 90%
Shipping Specification:
• HFOC-100A cable reel 1 pcs.
• User manual 1 pcs.
• Packing: Carton Box (size and weight depends on cable length)
Warranty Information:
Qtex warrants all optical extension cables to be free from defects in workmanship and materials, under
normal use and service, for a period of one (1) year from the date of purchasing from authorized reseller.
If a product does not work as it warranted during this period, Qtex will repair or replace
the defective product or its part. Replacement products may be new or reconditioned.
Warranty ends if the product has been damaged due to abuse, misuse, neglect, accident,
unusual physical or electrical stress, unauthorized modications, tampering, alterations, or
servicing other than by Qtex or its authorized centers, causes other than from ordinary use
or failure to properly use the Product in the application for which said Product is intended.
Armoured HDМI Active Optical Саblе
Zinc alloy
Gold plating
Protective shell
© 2021 Qtex Corporation. Qtex logo and its associated visual identity are trademarks or registered trademarks of Qtex Corporation
and/or subsidiaries. All other trademarks are the property of their respective owners. Qtex assumes no responsibility for any errors
that may appear in this publication. Product, pricing and feature information contained herein is subject to change without notice.