quadient Parcel Pending Lite Manual

B1
Accessories per
module
People Tools supplied
Accessories per column Accessories per
locker facility
x 2 x 2
Stacking and numbering rules
Module types
Type 3S
Type L+XS Type 2M
Assemble the modules in the order defined in your installation
plan (lockers are numbered from top to bottom and from left to
right).
A1
Bottom
A2
B3
Locker 1
Locker 7
Locker 8
Locker 10
Locker 11
Locker 21
Locker 20 Locker 24
Maximum modules per column = 4
Position 4
Position 1
Position 2
Position 3
Position 4
Position 1
Position 2
Position 3
Module
type [L+XS]
prohibited
Bottom
Back
Transport wedges
Push the module towards the back until it stops.
x 2
Remove the transport wedges from underneath
the module.
Type C LR14 alkaline
batteries Locker labels
x 4
Caps
x 4
Feet
x8
[B]
x 8
Feet fixing
screws
dx 2
Clips
Service door key
Place the foot fixing screws (b) in the holes of the foot (a).
Back
Type 4XS
x 2
Feet connectors Cleaning
wipes Spanner
g
Recommended batteries:
Duracell Pro
A7
If there is going to be a column adjoining
this one, use the feet connectors (e).
A8
Repeat steps A1 to A7 for the
other position 1 modules.
A3
Screw the foot in fully.
A4
Repeat steps A1 to A3 for the three remaining feet. Turn the module over and put it in its final
location.
Bottom Top
x 2
A5
Tighten the feet fixing screws with the service door key
(f).
Ensure that the module is stable. If not, adjust the foot that is not
in contact with the floor using the spanner (g).
A6
g
Stacking of
position 2/3/4
modules
Position 4
B
Position 3
Position 2
Position 1
B2
Bottom Top
x 2
Turn the module over then place it on top of the
module below.
Preparing position 1
modules
Position 4
A
Position 3
Position 2
Position 1
Parcel Pending Lite
Hardware Installation Guide

B4 B5 B7
B8
Repeat section
B steps for
position 2/3/4
modules
Repeat
sections A to
E steps for all
columns to be
assembled
Inserting new batteries supplied F1
Repeat section
Fsteps for all
modules
GLabel sticking on lockers
Numbering direction
G1 G2 G3 HChecking correct keypad operation
IRegistering the locker facility on the server
1. Launch the application on your mobile/PDA
2. Follow the instructions displayed on the screen
Ensure that both modules are correctly lined up with
each other.
Flush
surfaces Oset
surfaces
C
F
Push the latch of the upper locker of the module upwards to open
the locker door.
Use the service door key (f) to loosen the locking
screw then open the service door.
Turn the screw whilst simultaneously pushing upwards. If it is dicult or impossible to turn
the screw, check that the modules are correctly aligned (see step B4).
Close the service door and use the service door
key (f) to tighten the locking screw. Turn the screw whilst simultaneously pulling downwards. These
screws are no longer necessary.
Use the service door key (f) to loosen the locking
screw and open the service door.
Risk of explosion if the batteries
are replaced by an incorrect type
Close the service door then use the service door
key (f) to tighten the locking screw.
Insert the batteries.
Clean door area where the label is to be stuck using
the wipes supplied.
Stick the label on the door. Repeat steps G1 and G2 for all lockers.
112
11 22
If the indicator light comes on
for each module:
If the indicator light does not come
on for one or more modules:
Go to
the next
step
Check the
batteries
direction for
the module(s)
concerned.
For more information or if you encounter problems, please go to:
kb.quadient.co.uk/parcelpending_lite
Press the Cbutton on the keypad of each module to make sure
it works.
A0133192/B - 03/11/2020
D
d
Use the clips (d).
E
Optional step - Place the caps (c) in the locations without clips.
Locker 1
B6
F2
Optional
Removing fixing screws from the
highest locker of each column
Attaching adjacent columns of the
same height from the top
Positioning of caps on the top modules
of each column