Qualitel Eurofone C33H-B User manual

Eurofone C33H-B & C33H-W
Handset
User manual

Contents of the package
C33
 1 base station
 1 connector cable
 1 mains adapter 6 VDC / 300mA
 1 handset
 2 rechargeable batteries NiMH AAA 500 mAh
 1 user manual
Location
To obtain the best possible range, we recommend positioning the telephone in a
location central to your sphere of activity. Avoid positioning the telephone in
niches, recesses and behind steel doors.
The maximum range between the base station and handset is approximately 50
meters indoors and 300 meters outdoors. Depending on the surrounding
conditions as well as spatial and structural factors, the range may be smaller.
Silent zones can occur due to the digital transmission in the frequency range used
– even within the range, depending on the structural environment. In this case the
transmission quality may be reduced through the incidence of short breaks in
transmission. Normal call quality can be restored if you move slightly out of the
silent zone. If the range is exceeded, the call will be disconnected unless you
move back into range within five seconds.
To avoid radio signal interference from other electronic equipment, we
recommend that the base station and handset are situated at the greatest
possible distance (min. 1 meter) from other equipment.

Setting up the telephone
Setting up the base station
 Do not expose the base station to direct sunlight.
 Protect the base station against moisture. Do not position the base station in rooms
exposed to condensation, corrosive steam or excessive dust. Condensation can be present
in basements, garages, conservatories or sheds.
 The ambient temperature must be between 5 °C and 40 °C.
 Avoid positioning the telephone near heat sources such as heating elements or near
obstacles such as metal doors, thick walls, niches and cupboards.
There is no mains switch on the base station. For this reason the socket to which
it is connected must be easy to access.
Listening protection
When you are on the telephone, the base station and handset are connected to
each other over a radio link. The base station handles switching between the
telephone network and the handset. To ensure that no-one can eavesdrop or
telephone at your cost, the base station and handset exchange codes. If the
codes do not match, the connection with third-party handsets cannot be set up.

Setting up the telephone
Connecting the phone
Before you can start using your telephone you must plug in the telephone
connector cable and the mains cable.
Safety note
Use only the supplied mains adapter 6 vdc / 300 mA for the base station.
① Mains cable
First, insert the mains cable in the socket marked with the mains connector
symbol on the base of the base station. Then insert the mains plug in the 230 V
socket.
Note Your telephone will not function if the mains connector is not plugged in or
during a power failure.
② Telephone connector cable
Insert the one end of the telephone line cord into the wall jack and the other end
into the connector marked with the telephone symbol on the base station.
Setting up the handsets
Your handsets will be ready for operation (for making or accepting calls) only once
the batteries have been fully charged for the first time.
Inserting the rechargeable batteries
The bottom part of the handset contains a battery compartment for housing two
type AAA batteries (microcells).

Inserting the two rechargeable batteries (note the polarity!):
Insert the batteries in the battery compartment. Make sure the polarity is correct.
Insert the batteries so that the flat end (negative polarity) of the battery is pressing
against the spring. The handset will not function if the batteries are incorrectly
inserted. This may result in damage. Replace the compartment cover by placing it
approximately 3 mm offset and slide it upwards until it clicks into place.
Charging the batteries
The batteries are not yet charged when you first unpack the telephone. Insert the
handset in the base station for charging. The flashing battery symbol on the
handset shows the charging status. The batteries will take around 14 hours to fully
charge (initial charge).
Do not insert the handset in the base station without batteries.

Setting up the telephone
Once the new batteries have been inserted, the display on the handset indicates
the actual charging status only after a complete charging cycle.
Note You can replace the handset in the base station after every call. Charging is
electronically controlled to ensure optimal charging of batteries in different
charge states. Avoid removing the batteries from the handset for no good
reason, since this affects the optimum charging cycle.
You can telephone for up to 10 hours with fully charged batteries. The handset
has a standby time of up to 100 hours. When Full-Eco is switched on and
up to 200 hours if the function is switched off.
If the battery charge status has reached its lower limit, the battery symbol
flashes in the display and a warning signal is heard. You have 10 minutes of
talk time left.
C33

Get to know your telephone
Handset keys

Getting to know your telephone

Getting to know your telephone
Switch handset on/off
• Press and hold the End call key (approx. 5 sec).
• Press and hold the End call key to reactivate the handset.
About the menus
Menu navigation
In standby when pressing the soft key under .
Select the menus with the navigation key .
Press OK to confirm. To open the options list, use the navigation key to scroll
down the list to the preferred option, and confirm the option by pressing OK.
End menu
To exit a menu, press the End call key .
Set language
• Language default setting on delivery is English.
• To change the language:
1. Press the soft key under .
2. Press to scroll through the list, select HS SETTINGS and press OK to
confirm.
3. Press to scroll through the list, select LANGUAGE and press OK to confirm.
4. Press to scroll through the list, select the desired language and press OK to
confirm.