Quality Craft M450P-32ACH User manual

ATTENTION:
1. Find a location for the fireplace heater
that is protected from direct sunlight.
2. Do not plug the unit into the power outlet
before reading all instructions.
ELECTRIC FIREPLACE HEATER
INSTRUCTION MANUAL
M450P-32ACH
(NDF-65NB-1)

2
SAFETY INSTRUCTIONS
IMPORTANT
Please note when you open the carton
carefully check the unit and make sure
there are no damages. If you have any
problems with the unit, with how the various
functions work or with hidden damages or
missing parts please call 1-800-459-4409
(EST) immediately for service. NOTE: DO
NOT RETURN UNIT TO THE STORE BEFORE
CALLING THE TOLL FREE NUMBER. Do
not dispose of your cartons until you are
completely satisfied with your new fireplace
heater. Read all instructions thoroughly be-
fore operating your new Electric Fireplace.
NOTE: Light bulbs may become loose
during shipping. If the flame effect is dim
or does not work, please check that light
bulb or bulbs are finger tight in socket. See
instructions for replacing bulb or bulbs.
Please do not return the sample to the store
before checking light bulbs.
NOTE: The electric fireplace heater may
emit a slight harmless odor when first
turned on. This is caused by activating the
internal heater components for the first time
and should not occur again.
1) Read all instructions before using this
electric fireplace heater.
2) This electric fireplace heater is hot when
in use. To avoid burns, do not let bare skin
touch hot surfaces. The grill directly in front
of the heater outlet becomes hot during
heater operation. Keep combustible materi-
als, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 3 feet
(0.9 m) away from the front of the unit and
keep them away from the sides and rear.
3) Extreme caution is necessary when any
heater is used by or near children or indi-
viduals with disabilities and whenever the
fireplace is left operating and unattended.
4) Always unplug fireplace when not in use.
5) Do not operate any electric fireplace with
a damaged cord or plug or after the heater
malfunctions, has been dropped or dam-
aged in any manner.
6) Do not use outdoors.
7) This electric fireplace heater is not in-
tended for use in bathrooms, laundry areas
and similar indoor locations. Never locate
heater where it may fall into a bathtub or
other water container.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAU-
TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE
RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO
PERSONS, INCLUDING THE FOLLOWING:

3
8) Do not run cord under carpeting. Do not
cover cord with throw rugs, runners, or
similar coverings. Arrange cord away from
traffic area and where it will not be tripped
over.
9) To disconnect fireplace, turn controls to
off, then remove plug from outlet.
10) Connect to properly grounded outlets
only.
11) Do not insert or allow foreign objects to
enter any ventilation or exhaust opening as
this may cause an electric shock or fire, or
damage the heater.
12) To prevent a possible fire, do not block
air intakes or exhaust in any manner. Do
not use on soft surfaces, like a bed, where
openings may become blocked.
13) A heater has hot and arcing or sparking
parts inside. Do not use it in areas where
gasoline, paint, or flammable liquids are
used or stored.
14) Use this fireplace heater only as
described in this manual. Any other use
not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons.
15) Avoid the use of an extension cord
because the extension cord may overheat
and cause a risk of fire. However, if you have
to use an extension cord, the cord shall be
No.14 AWG minimum size and rated not
less than 1875 watts.
SAFETY INSTRUCTIONS
16) Do not plug this product into a receptacle
controlled by a wall switch or dimmer.
17) When storing or transporting the unit
and cord, keep in a dry place, free from
excessive vibration and store so as to
avoid damage.
CAUTION
If you use this heater in conjunction with
a thermal control, a program controller,
a timer or any other device that switches
the heater on automatically, remember to
observe all safety warnings at all times.
The heater has safety overheat protection.
If the overheat protection trips, switch off all
switch buttons and wait approximately 5 -10
minutes. It should reset automatically once
the unit cools down.
WARNING:
Procedures and techniques if not care-
fully followed - will result in damage to the
equipment. - will expose the user to the risk
of serious injury, illness or death.
This electric fireplace heater is for use on
120 volts. The cord has a plug as shown at
A in illustration below. An adapter as shown
at C is available for connecting three-blade
grounding-type plugs to two-slot recep-
tacles. The green grounding plug extending
from the adapter must be connected to
a permanent ground such as a properly
grounded outlet box. The adapter should not
be used if a three-slot grounded receptacle
is available.

4
A 15 AMP circuit is required to operate this
heater. If the breaker trips when the heater
is used then you may need to move the
heater to another location or unplug other
appliances that are on the same circuit. If
you require an extension cord use one that
is rated at 1875 watts.
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE.
PARTS LIST:
Fireplace insert 1
A) Top panel 1
B) Base panel 1
C) Side panel 2
D) Front panel 2
E) Upper front panel 1
F) Lower front panel 1
S) Connector 2
T) Short KD screws 3
U) Mounting clips 3
V) Mounting brackets 2
W) KD screws 51
X) Plastic connector 13
Y) SELF REPAIR SET
Touch-up repair paint (bottle)
L shape bracket 8
Screws for L shape 32
Plastic Connector 1
KD Screws 3
KD Nuts 3
Z) WALL ANCHOR SAFETY CABLE
Wall Anchor 1
Screw for wall anchor 1
Screw for mantle 1
Safety cable 1
TOOL REQUIRED: PHILLIPS HEAD SCREWDRIVER
MANTEL AND
INSERT ASSEMBLY:
WARNING: Make sure the fireplace INSERT
controls are in the OFF position and the
INSERT is NOT plugged in.
CAUTION: Place a piece of cardboard or
protective sheet on the floor in order to avoid
scratching the decorative surface of your
mantel during assembly.
SAFETY INSTRUCTIONS

5
Please DO NOT fully tighten the KD screws
until all panels are assembled.
Step 1: Attach 2 CONNECTOR [S] to the FRONT
PANEL [D] with 4 KD SCREWS.
(2 screws for each side) See Fig. A.
fig. A
Step 2: Attach all PLASTIC CONNECTOR [X]
to the PANELS [C, D and E] as shown in Fig.
B. (2 screws for each PLASTIC CONNECTOR).
fig. B
NOTE: If the KD SCREW(S) do not fit during
assembly, loosen the 2 screws to adjust the
PLASTIC CONNECTOR until the PANELS/KD
SCREWS can be installed.
Step 3: Attach the SIDE PANELS [C] to the
FRONT PANELS [D] with 4 KD SCREWS as
shown in Fig. C. (2 screws for each side).
fig. C
Step 4: Attach the LEFT and RIGHT SIDE
PANELS [C and D] to the BASE [B] using 4
KD SCREWS. (2 screws for each side) See
Fig. D.
fig. D
Step 5: Place the LOWER FRONT PANEL [F]
in between the lower section of 2 FRONT
PANELS [D] and attach with 2 KD SCREWS (1
screw each side). See Fig. E.
ASSEMBLY INSTRUCTIONS

6
fig. E
Step 6: Carefully place the INSERT into the
unit opening. The front of INSERT should
be flush with the front of the mantel. Once
the INSERT is in place, attach 2 MOUNTING
BRACKETS [V] with 2 KD SCREWS onto the
bottom of insert. (1 screw for each bracket)
See Fig. F.
fig. F
Step 7: Attach the UPPER FRONT PANEL [E]
over the upper section of 2 FRONT PANELS
[D] with 6 KD SCREWS. (3 screw for each
side) See Fig. G.
fig. G
Step 8: Attach 3 MOUNTING CLIPS [U] onto
the top of INSERT and lock in place with 3
SHORT KD SCREWS [T]. See Fig. H.
fig. H
Step 9: Install the TOP PANEL [A] to the unit
as shown and attach with 3 KD SCREWS.
See Fig. I.
ASSEMBLY INSTRUCTIONS

7
fig. I
Step 10: Tighten all KD SCREWS.
Step 11: Carefully move the assembled unit
to the desired location. The Fireplace Mantel
should not be positioned in area exposed to
direct sunlight.
WALL ANCHOR
SAFETY CABLE
The use of WALL ANCHOR SAFETY CABLE
is highly recommended in order to reduce
the risk of the fireplace being tipped over
accidentally. WARNING: This CABLE may
reduce possible risk of injury if the fireplace
is improperly handled, but is not a substi-
tute for proper adult supervision. Children
should not be left unattended near any
heater.
1. Drill a 5/16 in (8 mm) hole in the wall.
Insert the PLASTIC WALL ANCHOR into the
hole and gently tap until the flange on the
anchor is against the wall surface.
2. Position the back edge of the mantle close
to the wall.
3. Attach the SAFETY CABLE to the mantle
using the SCREW FOR MANTEL. See fig. J
4. Use the SCREW FOR WALL to attach the
other end of SAFETY CABLE to the wall.
5. Make sure all screws are tight.
fig. J
After reading complete instructions, confirm
all controls on fireplace are in the OFF posi-
tion. Plug the fireplace into a 15AMP/120Volt
outlet. If the cord does not reach, you may
use an extension cord rated for a minimum
of 1875 WATTS. Once the fireplace insert
has been properly connected to a grounded
electrical outlet, it is ready to operate.
OPERATION BY
THE CONTROL PANEL
The controls are located behind the grill
below the front glass and can be accessed
by pulling the grill from the top, forward
and down.
ASSEMBLY INSTRUCTIONS

8
OPERATION
ON/OFF: Press this button for main power
and flame effect. The indicator light will turn
on. See below for other control switches.
750W: For low heat function - Press this
switch while the ON/OFF switch is in the on
position for low heat. The indicator light will
turn on.
1500W: For high heat function - Press this
switch while the ON/OFF switch and the
750W switch are in the on position for high
heat. The indicator light will turn on.
TEMPERATURE CONTROL: To adjust the
temperature to your individual require-
ments, turn the temperature control dial to
the right (clockwise) to increase the desired
temperature and to the left for lower tem-
perature. This temperature control dial can
only be used while the ON/OFF switch and
750W & 1500W switches are in the ON posi-
tion. When the heater reaches the desired
temperature, the heater and 750W/1500W
indicator light will turn off but the fan will
continue to operate. Adjust this knob to
restart the heater.
DIMMER CONTROL KNOB: Turn the dimmer
dial clockwise or counter clockwise to get
the desired flame intensity. The dimmer
switch can only be used when the ON/OFF
switch is in the on position.
NOTE: When the ON/OFF switch is turned
off, all other heater functions will stop even
though the switches may be in the
on position.
NOTE: In order to shut down the heater
safely, it is recommended to turn the Tem-
perature Control knob to lowest setting and
allow the heater to cool down before press-
ing the ON/OFF switch to off position.
MAINTENANCE
WARNING:
Disconnect power and unplug the power
cord before attempting any maintenance or
cleaning to reduce the risk of fire, electric
shock or damage to persons. The bulbs in
your unit can become extremely hot. Allow
at least 10 minutes between turning off the
unit and removing the light bulbs to avoid
the accidental burning of the skin.

9
MAINTENANCE
RISK OF FIRE:
DO NOT EXCEED THE
RECOMMENDED BULB
WATTAGE.
REPLACING THE
LIGHT BULBS
Step 1: Remove 4 screws on the back
of fireplace and remove the rear
cover of the unit.
Step 2: You will find 2 X 40W Type B-10
bulbs under log-set bed.
Step 3: Loosen and remove burnt
out bulb(s) and replace with
new bulb(s).
Step 4: Close the rear cover and secure
with the 4 screws.
Step 5: Plug in the unit.
REPAIR SET
TOUCH-UP REPAIR PAINT
Paint directly on the mantel unit if
necessary. Fig. A.
Fig. A
REPAIRS
If any problems are found with the original
parts during mantel assembly such as the
panels cannot be installed with the plastic
connector. Try to solve by one of the follow-
ing methods.
Tools required: Electric drill, drill bits 3/4
inches (10 mm) or 1/16 inches (2 mm),
pencil, hammer, Philips screwdriver, safety
goggles and gloves (if necessary).
WARNING: Wear goggles before you start
drilling.

10
OPTION 1:
Use the spare KD NUTS, KD SCREWS and
PLASTIC CONNECTOR
1. Place the PLASTIC CONNECTOR on the
mantel unit and mark the drill-holes as
shown in Fig. B.
Fig. B
2. Drill the holes with diameter 3/4 inches
(10 mm) and depth 3/4 inches (10mm) on
the mantel. Each Plastic Connector needs 3
holes. See Fig. C.
Fig. C
3. Gently install the KD NUTS into the
drilled-holes with hammer as shown in
Fig. D.
Fig. D
4. Attach the PLASTIC CONNECTOR and
lock in place with KD SCREWS as shown in
Fig. E.
Fig. E
Option 2:
Use the SMALL L-BRACKETS and SCREWS.
1. Place the SMALL L-BRACKET to the unit
as shown and mark the drill-holes on the
mantel as shown in Fig. F.
Fig. F
MAINTENANCE

11
2. Drill the holes with diameter 1/16 inches
(2 mm) and depth 5/16 inches (8mm) on the
mantel. Each SMALL L-BRACKET needs 4
holes. See Fig. G.
Fig. G Fig. H
3. Attach the SMALL L-BRACKET and lock in
place with SCREWS as shown in Fig. H.
CLEANING
To clean unit first turn off controls on unit
and unplug the unit from power source. To
clean glass display panel; remove dust with
clean dry cloth or to remove finger prints
and other marks clean glass with clean
damp cloth. Do not use abrasive cleaners or
spray liquids on glass display panel surface.
Metal and metal painted parts should be
cleaned with damp cloth. Do not use
abrasive cleaners or spray liquids on
these surfaces.
WARRANTY
Every electric fireplace heater is tested
before it leaves the factory and it is guar-
anteed for one year. If the unit should fail
to operate correctly within one year from
the date of purchase, call customer service
at 1-800-459-4409 (EST). We will, at our
discretion either repair or replace the unit. It
will have to be returned to us freight prepaid
and we will return the repaired or replaced
unit to you freight prepaid. The company’s
sole obligation is to repair or replace the
unit. This warranty is void if in the opinion
of Quality Craft the unit has been tampered
with, altered, misused, damaged, abused
or used with the wrong power source. Light
bulbs are not covered by this warranty. The
warranty is for homeowner use only and
does not cover units used in commercial
situations.
Imported by
Quality Craft
Laval, Quebec, Canada H7S 2G7
1-800-459-4409 (EST)
www.qualitycraft.com
Made in China
CLEANING/WARRANTY