Quantum Rehab Q-Logic 2 Assembly instructions

Pride USA
Pride Mobility Products Corporation
182 Susquehanna Avenue
Exeter, PA 18643-2694
Pride Canada
Pride Mobility Products Company
380 Vansickle Road
St. Catharines, Ontario L2R 6P7
Pride UK
Pride Mobility Products Ltd.
32 Wedgwood Road
Bicester, Oxfordshire OX26 4UL
Pride Australia
Pride Mobility Products Australia Pty. Ltd.
20-24 Apollo Drive
Hallam, Victoria 3803
Pride Italy
Pride Mobility Products Italia S.r.l.
Via del Progresso, ang. Via del Lavoro
Loc. Prato della Corte
00065 Fiano Romano (RM)
Pride B.V.
Pride Mobility Products Europe B.V.
Castricummer Werf 26
1901 RW Castricum
The Netherlands
www.pridemobility.com
US_FC_GE_IT_SP_Q-Logic_2_Controller_BOI_Cover_RevA_Feb13_4499.pdf 1 2/20/2013 3:56:58 PM

1
2
12 13 14
8
10
11
9
8
7
6
5
3
4
1
2
12 13 14
8
10
11
9
8
7
6
5
3
4
IDENTIFICATION KEY CLE D’IDENTIFICATION LEGENDE
Copyright © 2013
Pride Mobility ProductsCorporation
INFMANU4499/Rev A/February 2013
CODICE DI IDENTIFICAZIONE CLAVE DE IDENTIFICACIÓN
US_FC_GE_IT_SP_Q-Logic_2_Controller_BOI_Cover_RevA_Feb13_4499.pdf 2 2/20/2013 3:56:59 PM

3
1
3
2
4 5
67 8
910 11
12 13 14
Regulador Pantalla LCD
Bloqueo de la funcion de condeccion
Palanca de selección de modo
y encendido/apagado
Palanca de mando Tomas mono
Botón de selección 1 Botón de menú Claxon
Botón de selección 2 Regulador de velocidad Puerto del cargador
Botón de luces
Botón del intermitente izqdo Botón del intermitente dcho
Steureng LCD-Anzeige Antriebs-/Funktionssperre
An/ Aus Modus Wahlshalter Hebel
Joystick Mono-anschlüsse
Auswahltaste 1 Menütaste Hupetaste
Auswahltaste 2 Geschwindigkeitsjustierung Ladegerätanschluss
Beleuchtungstaste
Linke Richtungsanzeigertaste Rechte Richtungsanzeigertaste
Centralina Visore LCD
TInhibizione trazione/funzione
Tasto di selezione modalità On/Off
Joystick Mono Jacks
Tasto di Selezione 1 Tasto di Selezione Menu Clacson
Tasto di Selezione 2 Selettore di velocità Porta del Caricabatterie
Tasto di Selezione Menu Pulsante freccia sinistra Pulsante freccia destra
Contrôleur Écran LCD
Fonction d’inhibition de l’entraînement
Levier «On/Off» et «Mode Select»
Manette Réceptacles «Mono»
Bouton «SELECT 1» Bouton de «Menu» Klaxon
Bouton «SELECT 2»
Sélecteur réglage de la vitesse Réceptacle du chargeur
Bouton des phares Bouton clignotant gauche Bouton clignotant droit
Controller LCD Screen Drive/Function Inhibit
On/Off Mode Select Lever Joystick Mono Jacks
Key 1 Select Button Menu Button Horn Button
Key 2 Select Button Speed Adjustment Charger Port
Light Button Left Turn Indicator Button Right Turn Indicator Button
CODICE DI IDENTIFICAZIONE CLAVE DE IDENTIFICACIÓN

4IDENTIFICATION KEY CLED’IDENTIFICATION LEGENDE
1
3
2
4 5
67
Control auxiliar Botón de Modo Piloto de Mode
Equipamientos opcionales
Indicador del Nivel de Bateria Botón On/Off
Palanca de mando Tomas On/Off y Modo
Steuerung für Begleitperson
Modus Taste LED Modus
Stellantrieb Anzeig Vier LEDs
Batterieanzeiger An/ Aus Taste
Joystick On/Off und Mode Jacks
Comando Guida Accompagnatore
Tasto di selezione Modalità Modalità LED
Indicatori di Attuatori
Indicatore di stato della batterie Tasto On/Off
Joystick On/Off e modalità Jacks
Contrôleur préposé Bouton de mode Voyants de «Mode»
Indicateurs d’actionneurs Jauge à batteries Cié de contact
Manette Jacks Marche/Arrêt et mode
Attendant Control Mode Button Mode LED
Actuator Indicators Battery Condition Meter On/Off Button
Joystick On/Off and Mode Jacks
1
2
3
4
5
6
7

5
CODICE DI IDENTIFICAZIONE CLAVE DE IDENTIFICACIÓN
1
3
2
4 5
6
4
5 6
2
1
3
Pantella mejorada Botón On/Off Pantalla LCD
Bloqueo de la funcion de condeccion
Puerto del cargador/programador Conector d-sub 9 contactos
Tomas On/Off y Modo
Erweiterte Anzeige An/ Aus Taste LCD-Anzeige
Antriebs-/Funktionssperre
Lade-/Programmieranschluss 9-Pin D-Sub-Stecker
On/Off und Mode Jacks
Visore Tasto On/Off Visore LCD
TInhibizione trazione/funzione
Porta del Caricabatterie/Programmatore Connettore 9 pin
On/Off e Modalità Jacks
Affichage amélioré Clé de contact Écran LCD
Fonction d’inhibition de l’entraînement
Port pour chargeur/Programmeur 9-pin D-sub Connecteur
Jacks Marche/Arrêt et mode
Enhanced Display On/Off Button LCD Screen
Drive/Function Inhibit Charger/Programmer Port 9-pin D-sub Connector
On/Off and Mode Jacks

6
WARNING! A Quantum Rehab Provider or a qualified
technician must perform the initial setup of this
product and must perform all of the instructions in this
manual.
The symbols below are used throughout this owner’s manual and on the
power chair to identify warnings and important information. It is very
important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/
situation. Failure to follow designated procedures can
cause either personal injury, component damage, or
malfunction. On the product, this icon is represented
as a black symbol on a yellow triangle with a black
border.
MANDATORY! These actions should be performed as
specified. Failure to perform mandatory actions can
cause personal injury and/or equipment damage. On
the product, this icon is represented as a white symbol
on a blue dot with a white border.
PROHIBITED! These actions are prohibited. These
actions should not be performed at any time or in any
circumstances. Performing a prohibited action can
cause personal injury and/or equipment damage. On
the product, this icon is represented as a black symbol
with a red circle and a red slash.
NOTE: These instructions are compiled from the latest specifications
and product information available at the time of publication. We
reserve the right to make changes as they become necessary. Any
changes to our products may cause slight variations between the
illustrations and explanations in this manual and the product you
have purchased. The latest/current version of this manual is available
on our website.
NOTE: This product is compliant with WEEE, RoHS, and REACH
directives and requirements.
SAFETY GUIDELINES

7
TABLE OF CONTENTS
LABEL INFORMATION ...................................................................8
Q-LOGIC 2 CONTROLLER..............................................................9
PRECAUTIONARY GUIDELINES ................................................9
OPERATING THE Q-LOGIC 2 CONTROLLER ........................10
On/Off and Mode Select Lever .......................................................10
Joystick Control ...............................................................................10
Lock/Unlock Procedure ..................................................................10
Speed Adjustment Knob .................................................................11
Keypad ...............................................................................................11
Horn Button ......................................................................................11
Menu Button .....................................................................................11
Key 1 and Key 2 Button ..................................................................11
Light Button ......................................................................................11
Left/Right Turn Indicator Button ..................................................11
LCD Screen .......................................................................................12
Drive Screen .....................................................................................12
Drive Profile Selection ....................................................................13
Actuator Adjustment (Seat Screen) .............................................13
Main Menu .........................................................................................14
Auxiliary (Aux) Menu .......................................................................19
Standby Select Menu ......................................................................19
Attendant Control/Stand-alone Joystick .....................................19
Enhanced Display ............................................................................19
SLEEP MODE ..................................................................................20
THERMAL ROLLBACK .................................................................20
BATTERY CONDITION METER .................................................20
Q-LOGIC 2 ERROR CODES .........................................................21
CARE AND MAINTENANCE ........................................................22
TEMPERATURE ..............................................................................22
WARRANTY .....................................................................................22

8
PRODUCT SAFETY SYMBOLS
The symbols below are used on the controller to identify warnings,
mandatory actions, and prohibited actions. It is very important for you
to read and understand them completely.
Read and follow the information in the owner’s manual.
Avoid exposure to rain, snow, ice, salt, or standing
water whenever possible. Maintain and store in a clean
and dry condition.
Disposal and recycling — Contact your Quantum Rehab
Provider for information on proper disposal and
recycling of your Pride product and its packaging.
LABEL INFORMATION

9
Q-LOGIC 2 CONTROLLER
The Q-Logic 2 Controller is a fully programmable, modular
electronic controller system that allows you to operate your power
chair. The Q-Logic 2 has several input devices available that operate
through a power module. The hand control will primarily be
discussed in this manual, along with references to the Enhanced
Display, Stand-alone Joystick, and Attendant Control. Additional
input devices are also available for the Q-Logic 2. Contact your
Quantum Rehab Provider for more information.
The controller has been pre-programmed to meet a typical user’s needs.
The program is adjusted using either a personal computer with software
provided by the controller manufacturer or with a hand-held programmer,
also provided by the controller manufacturer, by your Quantum Rehab
Provider or a trained service technician.
WARNING! The controller program can affect speed,
acceleration, deceleration, dynamic stability, and
braking. If it is programmed incorrectly or outside of
the safe limits as determined by your healthcare
professional, it can create a dangerous situation. Only
your Quantum Rehab Provider or a trained service
technician should program the controller.
NOTE: When a power chair is equipped with multiple input devices,
the device that powered up the chair will be in control.
PRECAUTIONARY GUIDELINES
Before operating the Q-Logic 2 Controller, please read the following.
These guidelines are provided for your benefit and will aid you in the safe
operation of the controller system.
 Turn off the power to the controller before you are seated in your
power chair.
Follow all of the procedures and heed the warnings as explained in
your power chair owner’s manual.

10
OPERATING THE Q-LOGIC 2 CONTROLLER
The Q-Logic 2 hand control is used to operate your power chair and all
of its components.
On/Off and Mode Select Lever
The On/Off and Mode Select lever turns the system on and off and is also
used to select drive profiles.
WARNING! Unless faced with an emergency situation, do
not use the on/off lever to stop the chair. This will cause
the power chair to stop abruptly.
WARNING! Always turn the power off when you are
stationary to prevent unexpected movement.
Joystick
The joystick controls the driving speed and direction of the power chair.
When the joystick is at rest, it is in the neutral (center) position and the
chair is stationary. In order to drive the chair, the joystick must be taken out
of neutral. Moving the joystick in any direction will switch the chair from
neutral to drive, and the chair will move in the direction indicated by the
joystick position. The farther away from the neutral position the joystick
is, the faster the chair will move in that direction. To stop chair movement,
simply release the joystick or move it back to the neutral position. The
chair’s electromagnetic brakes will engage after the chair has come to a
controlled stop.
Lock/Unlock Procedure
The Q-Logic 2 Controller comes with a programmable lock/unlock option.
NOTE: The lock-out feature is not programmed at the factory. To have
this feature added, contact your Quantum Rehab Provider.
To lock the controller:
1. Power the controller on.
2. Push and hold the On/Off and Mode Select Lever in the on position
until the controller turns off. The controller is now locked.
To unlock the controller:
1. Turn the controller on. The words “System Lock” will appear on the
display screen.
2. Move the joystick to the full forward position until you hear a beep.
3. Move the joystick to the full reverse position until you hear a beep.
4. Release the joystick. The controller is now unlocked.

11
Speed Adjustment Knob
The speed adjustment knob is used to control the speed of the power
chair.
To change the speed:
1. Push the On/Off and Mode Select Lever up once to power on the chair and
the controller.
2. To increase your speed, turn the speed adjustment knob up.
3. To decrease your speed, turn the speed adjustment knob down.
Keypad
The keypad is located directly in front of the joystick. It contains the
components that you will use to control your power chair.
Horn Button
The horn button activiates a warning horn.
Menu Button
The menu button is used to accesss user accessibility features such as
trip odometer reset and time set.
Key 1 and Key 2 Select Buttons
The key 1 select button is used to quickly and easily select drive profile
1. The key 2 select button selects the Seat. Contact you Quantum Rehab
Provider with any questions.
NOTE: If your Q-Logic 2 Controller is equipped with a lighting system,
the menu button and key 1/key 2 select buttons will be replaced with a
light button and left/right turn indicator buttons.
Light Button
The light button controls the front headlights and rear running lights.
To operate the lights:
1. Push the On/Off and Mode Select Lever up once to power on the
chair and the controller.
2. Press the light button once to activate the front headlights and rear
running lights.
3. Press the light button again to turn off the lighting system.

12
Left/Right Turn Indicator Buttons
The left/right turn indicator buttons toggle either the left or right turn
indicators.
To operate the turn indicators:
1. Push the On/Off and Mode Select Lever up once to power on the
chair and the controller.
2. Press the desired turn indicator button once to turn on that indicator.
3. Press the same turn indicator button again to turn off that indicator.
NOTE: If the left turn indicator is activated, pressing the right
indicator button will turn off the left indicator and activate the right
indicator.
NOTE: The turn indicator buttons also control the hazard lights.
Press both turn indicator buttons at the same time to activate the
hazard lights and press both buttons again to turn off the hazard
lights. If the hazard lights are left on and the controller is turned off,
the hazard lights will continue to flash. The Q-Logic 2 must be turned
back on and both turn indicator buttons must be pressed to deactivate
the hazard lights.
LCD Screen
The Q-Logic 2 provides the user with easily intuited feedback
information via the LCD screen. The circle at the bottom middle of the
screen represent a stoplight. A green light indicates full drive operation,
an amber light indicates limited drive operation, and a red light indicates
that drive operation is prohibited.
Drive Screen
The LCD provides the current time in either 12- or 24-hour clock
format, the current profile, drive operation, the speed adjustment
setting, the trip odometer, and the overall odometer reading.
Drive/Function Inhibit status is depicted as a green light in lower center
of the screen. Actuator adjustment will affect the inhibit status. As your
seat and/or back angle increases, a red light will indicate full drive
lockout. If your power chair is equipped with a seat lift, a yellow light
will indicate speed reduction as the seat is elevated. To return your
power chair to green status, reverse operation.

13
Drive Profile Selection
Your Q-Logic 2 Controller may be programmed for up to five drive
profiles that allow the system to be custom-tailored to your
environment. The drive profile may be changed two different ways.
Profiles 1-5 may be selected by pressing the On/Off and Mode Select
Lever in the forward direction. Profile 1 may be selected by simply
pressing the Key 1 select button. The selected profile is displayed on the
Drive Screen.
NOTE: Drive profiles are set by your Quantum Rehab Provider.
Contact your Quantum Rehab Provider to change or add a drive
profile.
To select a profile setting using the On/Off and Mode Select Lever:
1. Push the On/Off and Mode Select Lever up once to power on the
chair and the controller.
2. Push the On/Off and Mode Select Lever up again to select a drive
profile. Continue to cycle through the five available drive profiles.
NOTE: You can only scroll forward through the drive profiles.
Pushing the On/Off and Mode Select Lever down will power off the
controller.
WARNING! Drive/Function Inhibit status is read-only in
your actuator adjustment (seat screen). This function
is disabled in drive mode in order to prevent unintended
loss of function in your power chair. Take caution when
negotiating obstacles, ramps, and inclines. Whenever
possible, utilize an attendant in these conditions.
WARNING! Operating your power chair on inclines and/
or with tilt/recline function will affect your power
chair’s stability.
Actuator Adjustment (Seat Screen)
The Q-Logic 2 Controller can control five power seat actuators using
the mode select lever and the joystick.
To select and adjust an actuator:
1. Push the On/Off and Mode Select Lever up once to power on the
chair and the controller.
2. Push the On/Off and Mode Select Lever up several times until the
seat screen is displayed on the LCD or push the key 2 select button
once to go directly to actuator mode.

14
3. Push the joystick to the left or right to cycle through the available
actuators until the desired actuators are illuminated on the actuator
indicator. See figure 1.
4. When the desired actuator is selected, give a forward command to
the joystick to adjust position in one direction or give a reverse
command to the joystick to adjust position in the opposite direction.
5. Push up and release the On/Off and Mode Select Lever until you
return to the desired drive profile.
NOTE: The Drive/Function Inhibit status is affected only in the
actuator adjustment (seat screen).
Main Menu
The Main Menu screen displays a list of preference settings that are user
adjustable: 12-hr./24-hr. clock, amount of backlighting, measurement
system (miles/kilometers), English, German, Italian, French, and
Spanish language choice, and tripmeter and odometer resetting.
Figure 1. Actuator Selection
Tilt Mode
ALR/ELR
Mode (both)
ALR/ELR
Mode (right)
ALR/ELR
Mode (left)
Elevating Seat Mode Recline Mode Recline & ELR/ALR
Mode (both)

15
To make a selection from the Main Menu:
1. Push the Main Menu button.
2. Push the joystick up or down to scroll through the available main
menu functions.
3. When the desired function is highlighted on the LCD, push the
joystick to the right to select that function.
4. To return to the previous screen, push the joystick to the left.
Figure 2A. Menu Screens
Handcontrol Settings
System Settings
Main Menu
Sound
Display
Handcontrol Settings
Language
Day / Night
Brightness Day
Brightness Night
Measurement System
Set Time
Time format
Reminder
Display Display
Language
English
Display
Suono
Italiano
Language
Day / Night
Brightness Day
Brightness Night
Measurement System
Set Time
Time format
Reminder
Display Display
Day / Night
Off
Language
Day / Night
Brightness Day
Brightness Night
Measurement System
Set Time
Time format
Reminder
Display Display
Brightness Day
100%

16
Figure 2B. Menu Screens
14 :46
Language
Day / Night
Brightness Day
Brightness Night
Measurement System
Set Time
Time format
Reminder
Display Display
Measurement System
US
Display
Measurement System
EU
Language
Day / Night
Brightness Day
Brightness Night
Measurement System
Set Time
Time format
Reminder
Display
Language
Day / Night
Brightness Day
Brightness Night
Measurement System
Set Time
Time format
Reminder
Display
Language
Day / Night
Brightness Day
Brightness Night
Measurement System
Set Time
Time format
Reminder
Display Display
Time format
12h / 24h
Language
Day / Night
Brightness Day
Brightness Night
Measurement System
Set Time
Time format
Reminder
Display Display
Reminder
DISABLE
Display
Display
Brightness Night
30%

17
Figure 2C. Menu Screens
Command Beep
Mouse Command Beep
Seat Command Beep
Audible Profile Indicator
Sound Sound
Command Beep
Off
Handcontrol Settings
System Settings
Main Menu
Sound
Display
Handcontrol Settings
Command Beep
Mouse Command Beep
Seat Command Beep
Audible Profile Indicator
Sound Sound
Mouse Command Beep
Off
Command Beep
Mouse Command Beep
Seat Command Beep
Audible Profile Indicator
Sound Sound
Seat Command Beep
Off
Command Beep
Mouse Command Beep
Seat Command Beep
Audible Profile Indicator
Sound Sound
Audible Profile Indicator
Off

18
Handcontrol Settings
System Settings
Main Menu
Rest Distance
System Setting
Rest Trip
Rest Distance
Figure 2D. Menu Screens
To change units of measurement:
1. Push the On/Off and Mode Select Lever up once to power on the
chair and the controller.
2. Push the Menu button to access the Main Menu screen. See figure 2B.
3. Use the joystick to highlight the Handcontrol Settings option, then push
the joystick right to select that function. See figure 2B.
4. Use the joystick to highlight the Sound & Display option, then push the
joystick right to select that function.
5. Use the joystick to highlight the Measurement System option, then
push the joystick right to select that function.
6. Use the joystick to highlight the Max option, then push the joystick
right to select that function. See figure 2B.
7. Push the joystick left to select the ESC option and return to the Sound
& Display menu. See figure 2B.
8. Press the Menu button to return to drive mode.
To change the language choice:
1. Push the On/Off and Mode Select Lever up once to power on the
chair and the controller.
2. Push the Menu button to access the Main Menu screen. See figure 2A.
3. Use the joystick to highlight the Handcontrol Settings option, then push
the joystick right to select that function. See figure 2A.
4. Use the joystick to highlight the Sound & Display option, then push
the joystick right to select that function.
5. Use the joystick to highlight the Language option, then push the
joystick right to select that function.
6. Push the joystick up until the desired language is displayed. See
figure 2A.
7. Push the joystick left to select the Esc option and return to the Sound
& Display menu.
8. Push the Menu button to return to drive mode.

19
Auxiliary (Aux) Menu
The Aux Menu screen displays the auxiliary operations that are
available when operating in the Aux profile. In a standard basic system
with only a hand control and a power module, typically there is no Aux
profile. In more complex systems, an Aux profile provides access to the
operations made possible by the additional modules. Contact your
Quantum Rehab Provider for more information.
Figure 3. Aux Menu Screen
Standby Select Menu
The Standby Select Menu screen appears after the programmed timeout
when Standby Select is enabled. Standby Select allows the user to
navigate through the available profiles without the use of a Mode key.
The profile that was active when the timeout occurred is highlighted.
Contact your Quantum Rehab Provider for more information.
Attendant Control and Stand-alone Joystick
For more information on these applications, contact your Quantum
Rehab Provider.
The Attendant Control and the Stand-alone Joystick are similarly laid
out:
On/Off Button Battery Condition Meter
Enables/disables power Indicates battery charge
Actuator LEDs Mode LED
Indicates actuators in use Used for profile selection
Joystick
The joystick controls speed and direction in Drive mode.
Push the joystick to the right to select actuators in Seat mode.
Move the joystick forward or backward to activate the desired
actuator(s).
On/Off and Mode Jacks
Allow for remote On/Off and Mode switch installations
Figure 4. Standby Select Menu
Screen
Quick Access List
Aux Modes
System
Aux Menu
Drive 1
Drive 2
Drive 3
Seat
Aux Menu
Standby Select

20
Enhanced Display
The Enhanced Display module is primarily used with specialty control
devices like a head array. It also can be used to provide a graphical
display for the Stand-alone Joystick. When used with the hand control,
it provides a larger display than the hand control’s LCD. The Enhanced
Display is mainly used in more advanced applications. Contact your
Quantum Rehab Provider for more information.
The Enhanced Display has the following controls:
On/Off Button
Enables/disables power
On/Off and Mode Jacks
Allow for remote On/Off and Mode switch installations
9-pin D-sub Connector
Allows for connection of a specialty control device
LCD Screen
A color LCD display that may be equipped with built-in infrared
(IR) for remote control and with Bluetooth mouse control
SLEEP MODE
The Q-Logic 2 Controller offers a sleep mode feature that will shut off
the main power if the joystick remains stationary for a programmed
period of time from 0 to 240 minutes. To restore power and resume
operation of the chair, push the On/Off and Mode Select Lever up once.
A set time of 0 minutes disables the sleep mode feature.
THERMAL ROLLBACK
The Q-Logic 2 Controller is equipped with a thermal rollback circuit
that monitors the temperature of the chair’s motors and controller. If
either exceeds the safe operating temperature, the controller reduces the
output to 20% of full operation level. This reduces the chair’s speed and
allows a cool-down period. Once the temperature returns to a safe level,
the chair will resume normal operation.
BATTERY CONDITION METER
The battery condition meter is located in front of the joystick on the
hand control and as an LED on the Attendant Control and Stand-alone
Joystick.