quiko QK-KEY User manual

Via Seccalegno, 19 – 36040 Sossano – Vicenza – Italy
Tel [phone] Fax [phone] [e-mail]
www.quiko.biz
Installation Guide
● QK-KEY – Surface Mount

QK-KEY Installation Guide
General:
The QK-KEY encoder is safe and comfortable access control products.
Get an individual access code.
The device includes an environment resistant An optional bypass pushbutton enables easy
Internal opening (the opening time is programmable)
Features:
Installation possibilities: on wall, under
plaster, inside aluminum panel
Power failure resistance, keeps the access
codes in nonvolatile memory
Easy installation, programming and
operating.
Environmental and anti vandal resistance.
Works with AC or DC power supply Up to 100 million possible combination codes
up to 98 simultaneously different access
codes
optional bypass exit pushbutton
Different and programmable opening time
from keyboard and bypass pushbutton
Specifications:
Operating voltage: AC/DC 1 V 800mA or
4Vdc
Code length: -6 keys
Operating electric or magnetic lock. (normally
open or normally close)
Opening time: 1-9 seconds
Dimensions: Surface Mount: 110X100X35mm
(H*W*D)
Color: silver or bronze
Installation:
Setting J5 Jumper according to the lock type
Desirable RLY state when enterin the
correct code
Jumper J5
Close circuit (Normally open) for electric lock Jumper on right pins (default state)
Open circuit (Normally close) for magnetic lock Jumper on left pins
After installing the lock in the door frame. Route the following wires to the encoder:
1. wires from power supply.
. wires to the lock.
3. wires from optional bypass pushbutton.
Using a Phillips screwdriver open the plastic top cover screws, carefully pull up the panel.
Expose the 4 covered insulations bores and the round wires bore.
Attach the base of the encoder to the wall, using a pencil mark the 4 fixing points.
Drill the 4 fixing points on the wall.
Route the wires through the round bore in the base of the encoder.
Using 4 screws install the base to the wall.
Verify the power supply is not connected to power source!
Connect the wires to the circuit board terminals according to the circuit’s labels, the attached
electrical diagram and the following instructions.
Connect: Power supply to the two 12VAC terminals.
One wire from the lock to the RLY terminal. The second wire from the lock to one of 12VAC
terminal. Short wire from the second 12VAC terminal to the second RLY terminal.
(the RLY functions as a switch)
the polarity of the wires is not significant.
Reassemble the panel over the base.
Attach the top cover to the base using the 4 screws.
Connect the power supply to the power inlet, the red led will constantly illuminate, indicating
power supply to the encoder. The green led will blink for seconds indicating correctly
initiation.

QK-KEY Installation Guide
3
Pro rammin :
100 memory cells 8 digits long each one, available.
Cell 00 is used for door opening times values storage.
Cell 99 is used programming code value storage.
The rest of the 98 cells from 01 to cell 98 are used for different access codes values storage.
Code length is minimum digits and, maximum 8 digits. (Recommended 6 digits for
programming code, and 4 digits for access code)
Programming code, access codes and opening times values are programmable via the
keyboard.
Programming mode: in order to store new access code, set opening times or changing the
programming code, you should enter to the Programming mode.
After clicking the valid programming code (manufacturer code if not changed is ⇒1 3456
confirm with*) the green led is blinking, now you can do the required programming as
described in the following examples. When finished you can enter more access codes or exit
this mode to the regular state by typing #.
Each key stroke is followed by a Beep sound, entering a false code or invalid typing is
followed by a “Beep-Beep-Beep” sound sequence. Entering a valid sequence to memory cell is
followed by a long “Beep” sound.
If the programming mode is not exit. A timer exits the encoder to regular mode.
Examples:
Storin a new access code
Enter the programming code: if not changed is: 1 3456 confirm with *, the green led will
blink.
now the following sequence should be entered: memory cell number ( digits), access code
( -6 digits),and for verification again the same memory cell number, the same access code.
Confirm with *. To finish press: #.
You can add more access codes in cells 01-98 in the same way.
-to use the access code: press the access code followed by *.
Chan in the pro rammin code
Enter the programming code: if not changed is: 1 3456 confirm with *, the green led will
blink.
now the following sequence should be entered: memory cell number 99 , new programming
code ,and for verification again the memory cell number 99, the same new programming
code. Confirm with *.
Now you can add access codes in cells 01-98 as described or exit.
To finish press: #.
You should keep this code because this is the only way to enter the pro rammin
mode!
Back to Initiate status – default
Using an internal jumper the initial programming code can be restored. The access codes will
not be changed.
Turn the power off. Dismount the panel. Install a jumper on pins labeled: DEFAULT turn on
the power, a long “Beep” will be sound for confirmation.
Turn off the power and take out the jumper. Reinstall the panel.
The encoder returns to normal condition. The Programming code now is: 1 3456 *.
Cancelin an access code
A particular access code could be cancel if its memory cell location is known.
Enter the programming code: if not changed is: 1 3456 *, the green led will blink.
now the following sequence should be entered: memory cell number to cancel( digits), and
# # .for verification again the same memory cell number, and # #. Confirm with *.
For example: canceling the code stored in cell number 37:
press the following sequence: ⇒ 37,# #,37, # # *.
To finish press: #.

QK-KEY Installation Guide
4
Settin openin times values
A different opening time value can be set to opening via the keyboard and via the optional
bypass pushbutton.
The times values are from 1 second till 9 seconds.
Enter the programming code: if not changed is: 1 3456 *, the green led will blink.
now the following sequence should be entered: memory cell number 00, opening time via
keyboard (1 digit) followed by opening time via bypass pushbutton (1 digit). for verification
repeat the same sequence of memory cell number 00 opening times values. Confirm with *.
To finish press: #.
Remark: when setting the keyboard opening time, a value to the bypass pushbutton must be
set also, even if not installed.
Summery and examples
Programming option execution default
Entering programming code ⇒ 1 3456 *
Changing programming code
For example: new code
777456
Enter programming code *
⇒ 99-777456 99-777456 *
#
1 3456
Storing a new access code
For example: cell number 01
access code: 040
Enter programming code *
⇒ 01- 040 01- 040 * #
All the cells are empty
(not 0)
Canceling access code stored
in cell number 37
Enter programming code *
⇒ 37-# # 37-# # * #
Setting opening time from
keyboard to seconds and
from bypass pushbutton to 5
seconds
Enter programming code *
⇒ 00- 5 00- 5 * #
3 seconds from keyboard,
3 seconds from bypass
pushbutton
operation
Openin the lock usin the keyboard
Enter the access code confirm with *.
The lock will be open for the time value it was programmed.
Each key stroke is followed by a Beep sound, entering a false code or invalid typing is
followed by a “Beep-Beep-Beep” sound sequence
When exit the secured room press the bypass pushbutton, the lock will be open for the
programmed time value (could be set to different value than entering).

QK-KEY Installation Guide
5
Electrical Drawin
REX LINE12VAC
Relay
RLY
DEFAULT
1 V
AC
Bypass
pushbutton
Electric lock
RLY = Normally open
Jumper as in drawing