Quiko QK-AMBANT User manual

www.quikoitaly.com 



QK‐AMBANT



QK‐AMBANTisatriggerantennathatallowsactivatingatransmittingtagwhenthisoneentersthedetectionrangeof

theantenna.QK‐AMBANTisequippedwithacontactforpresencedetectorslikephotocellsandloopdetectors.



1. TECHNICALCHARACTERISTICS

QK‐AMBANT

Operatingfrequency



125kHz



Powersupply



230Vac+/‐10%



Consumption<50mA



Radiatedpower



<25mW



Wiring4wires(section0,5mm2)



Operatingtemperature‐20°C/+55°C



ProtectionrateIP66



Dimension350x310x40mm



Enablingarea(hands‐freemode)



5m



Maximumdetectionspeed



50km/h



www.quikoitaly.com 



2. CONNECTION



Connectthepowersupplywiretothe230Vacandconnectthe4signalwiresasfollows:



SignalCablecolour



Presence+(12V)



Red



‐(GND)



Black



SyncINGreen



SyncOUTWhite



Ifthepresencedetectionsignal(red)isnotused,pleasejoinittotheblackwire(GND),andthedevicewillalways

detectpresence.

Incaseofusingmorethanonetriggerantennainseries(maximum4),connectthesynchronismsignalOUTtothe

synchronismsignalINofthefollowingactivator,toavoidinterferencebetweenthem.Seeconnectiondiagramabove.

IfyouwanttoconnectonlyoneantennajointhetwosynchronismsignalsINandOUT.



www.quikoitaly.com 



3. INSTALLATION

1.Equipment

2.Adhesivelabel

3.Wallfixingholes

4.Configurationpushbutton

5.Led

6.Mountingbracket



3.1.WALLINSTALLATION



www.quikoitaly.com 



3.2.INSTALLATIONWITHBRACKET



4.CONFIGURATIONOFCHANNELSANDGROUPS



Usethebutton(4)toconfiguretheoperatingmodeoftheantenna

Channelconfiguration:Keeptheconfigurationbuttonpresseddownuntilthenumberoflongredsignalsis

equaltothechanneltobeconfigured.Forexample,ifyouwanttoconfigurechannel2,releasethebutton

afterthesecondlongredsignal.

Channelconfigurationallowsselectingthechanneltobesenttotheradioreceiverbythetransmittingtag.



Groupconfiguration:Presstheconfigurationbuttonandkeepitpresseddown.Theledwillissuethered

channelconfigurationsignalsfollowedbyaseriesofflashinggreensignalstoindicatethatitwillstartthe

groupselectionsequence(longgreensignalsindicatinggroups1to7).Releasethebuttonattherequired

group.Forexample,ifyouwanttoconfiguregroup5,releasethebuttonafterthefifthlonggreensignal.

Groupconfigurationallowstocontrolseparatelyupto28differentdoors.

Theprocedurecanbecarriedoutasmanytimesasrequired.



www.quikoitaly.com 



EXAMPLE:Channel2Configuration



Operatingmode=green



Pressbuttontoselectchannel=red



Channel1Channel2Channel3Channel4



Releasebutton

EXAMPLE:Group5Configuration



Operatingmode=green



Keepbuttonpresseddownto=Flashinggreen

selectgroup

Groupopen



=green