QULOMVS HKOFOC008 User manual

Assembly Instructions
HKOFOC008

Assembly Instructions
ASSEMBLY REQUIREMENT
ASSEMBLY REQUIREMENT
1 PERSON ASSEMBLY | 30 MINUTES ASSEMBLY TIME (APPROXIMATE)
TOOLS REQUIRED: ALLEN WRENCHES (PROVIDED)
1. Remove all packaging materials, staples and packing straps from the carton.
2. Refer to Parts Checklist and ensure they are complete before you start assembling.
TIPS FOR ASSEMBLY
1. Allow ample room for assembly and in close proximity to where product will be placed.
2. Assemble the product on a surface that does not scratch or damage the exterior and finish of the furniture.
3. During assembly, do not over-tighten any fittings as this may cause damage.
4. Do not sue power tools to assemble this product.
5. Do not sit or stand on the partially assembled product, only use the product for which it is intended.
CARE AND USE
Recommended for indoor and residential use only.
Wipe with a soft, dry cloth. Do not use harsh abrasives or household cleaners as they may damage the
finish.
Check all the fittings periodically and re-tighten as necessary. Do not use the product if any of the parts is
damaged or broken.
Page 1
HKOFOC008

Qulomvs Office Chairs Limited Warranty
1 YEAR on compoment parts including Control Mechanisms, gas cylinder, wood, plastic parts,
Qulomvs Office chairs are warranted from the date of purchase against failuredue to material
and workmanship as follows
1 YEAR on Upholstery mesh and foam against wear and deterioration.
base and casters.
To make a warranty claim, please contact Qulomvs, provide model number, proof of purchase and
description of the problem.
At it’s option Qulomvs will:
a) Supply compatible components of current manufacture.
b) Send a new product if necessary, customer must return the original product to the warehouse.
RETURN POLICY
Customers can request to return the item within 30 days of receiving it.
Page 2

Page 3
Step 1：Insert Base Legs[ H ] one by one to the Base Center[ G ]. Next, screw ten Screw[ S ] into
the holes with the Allen Wrench[ Q ]to attach the base and the legs.
Sx10
Px4 Qx1 Rx1
Ix5
Ex1 Fx1 Gx1 Hx5
Ax1 Bx1 Cx1 Dx1
Ox4
8x25
K2x4
6x18
Jx2 K1x7
8x 35
Lx2
Mx2
8x2 0
Nx3
6x25
6x18
S*10
H
G
Q

Page 4
Step 2：Insert the casters [ I ] into the five star base. This may take significant force. Gentl
squeeze the base cover and place around the center of the 5 star base. Insert the gas lift
into the center of the base.
F
I
I
I
I
I
Step 3：Align the Mechanism [ E ] over the pre-drilled holes underneath the Seat Cushion [ B ],
make sure the front of the mechanism is facing the front of the Seat. Attach the
Mechanism to the Seat with Screws [ O ].
Note：Do not tighten all screws to 100%, make sure it have space to adjust in the next steps.
B
E
O

Page 5
Step 4：Attach the Backrest [ A ] to the Seat Cushion with Washers [ K1 ] and Screws [ N ].
Step 5：Attach the Armrest [ D ] to the Seat Cushion [ B ] and Backrest [ A ] with washers [ K1 ],[ K2 ],
Screws [ J ],[ L ] and Cover [ P ].
Note：Screw [ J ] attach the armrest to backrest; Screw [ L ] attach the armrest to seat cushion.
NK1
A
K2
PL K1
PJ K1
K2
D
The backrest needs to be inserted into the tray,
not attached to the outside when installed.

Step 6：Attach the Headrest [ C ] to the Backrest with Screws [ M ] and Cover [P ].
Step 7：Insert the Seat Base into the tilt mechanism.
M
R
C
Page 6

Page 7
Step 8：Enjoy your Office Chair!

Page 8
CONTACT INFO: [email protected]
Missing something?


