Quoizel WVR9007A User manual

Package Contents
Warnings and Cautions
1of2
For Style WVR9007A
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
markingpen,1/16”
drillbit,centerpunch,hammer,drillandwrench.
(1)A21MediumBaseBulb150WMaximum,MediumBaseT9Vintage Bulb is recommended, bulb not included.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses,
Fixture
Body
x1
Installation Guide #IS-WVR9007A
2018 QuoizelInc. ReleasedDate:2018-10-08
visit us on-line at www.quoizel.com
B
AMounting Screw
x3
Glass Panel
x4
C
STEP 1 Remove the Cage from the Fixture Body-
A. Unlock lock balls on the bottom of the Fixture Body (C) to remove
the cage.
Figure 1
Cage
C
Fixture Body
Lock Ball
STEP 2 Install Glass Panel-
A. Insert the Glass Panel (B) into the
slot in the top edge of the cage.
Secure the Glass Panel (B) by
pressing the tabs on to the bottom
edge of the cage onto the bottom
edge of the Glass Panel (B).
Tab
Slot
Tab
B
Cage
Figure 2
STEP 3 Install Bulb and Cage-
A. Insert the bulb onto the socket and
screw snugly into place.
B. Place the bolts on the bottom edge
of the cage back onto the Fixture
Body (C) and secure with
previously removed lock balls.
Hand tighten until snug.
T9 Vintage Bulb
(recommended
but not included)
Socket
Lock Ball
Fixture Body
Cage
Bolt
Figure 3

2of2
2018 QuoizelInc. ReleasedDate:2018-10-08
visit us on-line at www.quoizel.com
STEP 8 Attach the fixture to
the Post Mount
-
A. Place the fixture on the post
lining up the mounting holes
on the fixture fitter with the
holes on the post. Use the
Mounting Screws (A) to
attach the fixture to the post.
Your fixture is now
assembled and ready to use.
Enjoy! Post
Hole
Fixture
Fitter
Mounting
Hole
Post Lighting
A
Figure 8
STEP 4 -Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Fixture
Fitter Marking Pen
Mounting
Hole
Post
Lighting
Post
Post
Fixture
Fitter
STEP 6 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
post at each (3) locations marked in step 5 above.
1/16” bit and drill
Post
Figure 4
STEP 5 M C
EM H
-arking the enter of
ach ounting ole
A. Remove the light fixture. Using
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
Center Punch
Hammer
Marking
Post
Figure 5
STEP 7 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Figure 6
WVR9007A
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
7”
20.5”
Figure 7
FINISH: ANTIQUE BRASS
7”