QUPIT 159-01 User manual

DA16-0500-00
Installation manual
boiler gateway “Adam”
Model 159-01
Nederlands | English

2 | cv-gateway “Adam”
Nederlands
Inhoudsopgave
Vooraf 4
Voorzorg en veiligheid 4
Meer informatie 5
Pakketinhoud 5
De installatie 5
Verbind met het netwerk 5
Aansluiten op de cv-ketel 7
Het gedrag van de LED 8
English
Table of contents
Before you start 10
Precautions and safety 10
More information 11
In the package 11
Connect to the network 11
Connect to the boiler 13
The LED behaviour 14

3 | cv-gateway “Adam”
NL
Copyright 2017, Plugwise.
Alle rechten voorbehouden.
Dit document bevat informatie over de
installatieprocedure en de
functionaliteiten van dit product. Omdat
Plugwise de producent is van dit product
vermelden wij alle relevante
functionaliteiten in deze handleiding. De
beschikbare functionaliteiten zijn
afhankelijk van de OpenTherm-
thermostaat en cv-ketel waarop de Qupit
cv-gateway “Adam” is aangesloten.
Plugwise B.V. verklaart hierbij dat dit
product voldoet aan de benodigde
vereisten van de desbetreffende
Europese richtlijnen, waaronder
1999/5/EC (R&TTE). Een exemplaar van
de Europese conformiteitsverklaring is
beschikbaar op
www.plugwise.nl/product-conformity.
Oude elektrische en elektronische
apparaten bevatten vaak waardevolle
materialen. Plaats een afgedankt
apparaat dan ook nooit bij het gewone
afval. Lever altijd het apparaat in bij een
gemeentelijk inzameldepot voor
elektrische en elektronische apparatuur.

4 | cv-gateway “Adam”
Vooraf
Dit is de installatiehandleiding voor de
Qupit cv-gateway “Adam”.
Met de cv-gateway is het mogelijk de
kamertemperatuur te regelen zonder dat
hiervoor de huidige thermostaat moet
worden gebruikt, een schema in te stellen
en wordt het stookgedrag via graeken
inzichtelijk gemaakt. Daarnaast leest de
cv-gateway de cv-ketel uit, zodat de
installateur jouw verwarmingsinstallatie op
afstand kan monitoren.
Uitleg symbolen:
Let op, waarschuwing!
Deze stap moet je uitvoeren
Tip
thermostaat verbinden, mogen niet
langer zijn dan 50 meter en geen
grotere weerstand dan 5 Ohm per
draad hebben.
Als dit wel het geval is, adviseren wij
de draden te laten vervangen.
Haal de spanning van de cv-ketel
voordat je verder gaat.
Controleer vooraf de aanwezigheid en
kwaliteit van de wi-netwerkverbinding
en de beschikbaarheid van een vrij
stopcontact bij de cv-ketel.
Zorg ervoor dat je het wachtwoord
van het wi-netwerk waarmee je de
cv-gateway gaat verbinden bij de hand
hebt.
Houd het short ID en de netwerknaam
van de cv-gateway bij de hand. Het
short ID is de 8-letterige code op de
sticker op de achterkant van de cv-
gateway. De netwerknaam begint met
“smile_”. Beiden heb je nodig tijdens
het instellen van het wi-netwerk.
Voorzorg en
veiligheid
We adviseren je om de cv-gateway
door een professionele
ketelinstallateur te laten installeren.
De bestaande cv-draden, die de
cv-ketel met de thermostaat
verbinden, moeten op de ketel zijn
aangesloten op de OpenTherm-
aansluiting. Je vindt dit terug in de
handleiding van de cv-ketel.
De cv-draden die de cv-ketel met de
stuvwxyz
ssid: smile_abcdef
Short ID
Netwerknaam

5 | cv-gateway “Adam”
NL
Meer informatie
Sluit de adapterkabel aan op de
adapter en de cv-gateway. Steek de
stekker in het stopcontact.
Wacht tot de cv-gateway is
opgestart: het bovenste en middelste
lampje knipperen langzaam.
Wi via WPS?
Wi via WPS wordt alleen
ondersteund via een speciale
WPS-knop op de router.
Druk 2 seconden op de zwarte knop
op de cv-gateway. Wacht tot het
bovenste lampje snel en regelmatig
blijft knipperen.
Activeer wi via WPS op de
wi-router om te verbinden met het
wi-netwerk.
Als de cv-gateway na 2 minuten nog
geen verbinding heeft gemaakt met
een wi-netwerk, wordt de
cv-gateway opnieuw in
aanmeldmodus gezet.
Wi?
Wil je de cv-gateway
verbinden met wi en
maak je gebruik van een
Android-toestel? Zoek
dan naar de Plugwise connect app in
de Google Playstore. De app begeleidt
Pakketinhoud
Short ID
Netwerknaam
Meer informatie over de cv-gateway vind
je op onze website:
www.getqupit.com/cv-gateway.
In het pakket van de cv-gateway vind je:
1. Qupit cv-gateway
2. Muurplaatje
3. Installatiekabel voor naar de cv-ketel
4. USB-adapter
5. Adapterkabel
6. Installatie-instructie
7. Installatiekaart (achterin de
installatie-instructie)
De installatie
De installatie bestaat uit 2 stappen:
1. Verbind de cv-gateway met het
(wi-) netwerk.
2. Sluit de cv-gateway aan op de kabels
tussen de cv- ketel en de
thermostaat in.
Verbind met het netwerk
Doe dit bij de cv-ketel. Zo weet je
zeker dat er voldoende wi-bereik is.

6 | cv-gateway “Adam”
je tijdens het aansluiten van de
cv-gateway op het wi-netwerk.
Geen Android? Volg dan onderstaande
stappen om de cv-gateway te verbinden
met het wi-netwerk.
Verbind je smartphone of tablet met
het wi-netwerk van de cv-gateway
dat begint met ‘smile_’.
Voer als wachtwoord het short ID in.
Ga in de webbrowser van je
smartphone of tablet naar
http://192.168.40.40. Omdat je
verbonden bent met het netwerk van
de gateway zal de pagina “Instellingen”
> “Netwerkinstellingen” automatisch
openen.
Druk op “Scan” en selecteer je eigen
wi-netwerk.
Voer het wachtwoord van je eigen wi-
netwerk in en sla de instellingen op.
Zorg ervoor dat je je smartphone of
tablet weer verbindt met het wi-
netwerk waar je zojuist de cv-gateway
mee hebt verbonden.
Netwerkkabel?
Sluit een netwerkkabel aan tussen de
router en de cv-gateway.
Netwerkverbinding controleren?
Gebruik hiervoor een smartphone of
tablet die is verbonden met het
netwerk waarmee ook de cv-gateway
is verbonden.
Ga naar https://adam.plugwise.net
Log in met je short ID. De webpagina
van de cv-gateway opent.
Niet gelukt via wi?
Druk de zwarte knop op de cv-
gateway 5 seconden in: het middelste
lampje knippert 5 keer, het bovenste
lampje gaat vervolgens snel
knipperen.
De netwerkinstellingen worden
gewist. Wacht tot de cv-gateway weer
is opgestart en probeer opnieuw met
het wi-netwerk te verbinden.

7 | cv-gateway “Adam”
NL
Aansluiten op de cv-ketel
Installatiediagram Adam met thermostaat
Maak bij de cv-ketel de draad tussen
de cv-ketel en thermostaat los en
plaats hiervoor in de plaats de
installatiekabel voor de cv-ketel.
Sluit de draden die naar de ketel
lopen aan op de cv-gateway bij het
icoon van het vlammetje.
Sluit de draden die naar de
thermostaat lopen aan op de
cv-gateway bij het thermostaat-
icoon. Hiervoor maak je gebruik van
de bestaande draden.
Bepaal de positie van de cv-gateway
bij de cv-ketel en monteer het
bevestigingsplaatje van de
cv-gateway.
Klik de cv-gateway op het
bevestigingsplaatje.
Zet de spanning terug op de cv-ketel.
Steek de stekker van de cv-gateway
weer in het stopcontact en wacht tot
deze is opgestart.
Installatiediagram Adam met slimme
thermostaat
Gebruik de handleiding van de ketel
voor informatie over de
ketelaansluiting.
Sommige slimme thermostaten
hebben een gateway die met de ketel
verbonden is. Plaats in dat geval de
cv-gateway tussen de gateway van de
thermostaat en de ketel in.
Haal de spanning van de cv-ketel en
van de cv-gateway.

8 | cv-gateway “Adam”
Open de
webpagina
Heb je de cv-gateway verbonden met
het internet? Zorg er dan voor dat je
smartphone of tablet verbonden is
met hetzelfde netwerk als waarmee
ook de cv-gateway is verbonden.
Ga naar https://adam.plugwise.net
Log in met je short ID
De webpagina van de cv-gateway
opent. Hier kun je de
kamertemperatuur regelen, een
schema instellen en wordt het
stookgedrag inzichtelijk via graeken.
Het gedrag van
de LED
In de onderstaande tabel wordt het
belangrijkste gedrag van de LED’s op de
cv-gateway toegelicht.
LED Kleur Patroon Omschrijving
Groen Langzaam
knipperen
De cv-gateway is in aanmeldmodus
Groen Knipperen Communicatie met het wi-netwerk
Groen Knipperen Status van de cv-gateway
Groen Knipperen Communicatie met het LAN-netwerk

9 | Boiler gateway “Adam”
EN
Copyright 2016, Plugwise.
All rights reserved.
This document contains the installation
procedure and functional description of
this product. Because Plugwise is the
manufacturer of this product, we include all
relevant functionalities in this manual.
The provided functionalities for Adam
depend on the OpenTherm thermostat and
boiler to which the Qupit boiler gateway
“Adam” is connected to.
Plugwise B.V. hereby declares that this
product is in compliance with the applicable
essential requirements of the appropriate
EC-Directives, including 1999/5/EC
(R&TTE). A copy of the EU declaration of
Conformity is available at
www.plugwise.com/product-conformity.
Old electrical and electronic appliances
very often contain valuable materials.
Therefore, never dispose discarded
appliances with normal household waste.
Always hand in your old appliances at the
municipal collection points for electrical
and electronic equipment.

10 | Boiler gateway “Adam”
Before you start
This is the installation manual for the
Qupit boiler gateway “Adam”.
With the boiler gateway it is possible to
regulate the room temperature without
the need of the room thermostat, set a
schedule and visualising heating behaviour
using graphs. Besides, the boiler gateway
reads out the boiler so the central heating
system can be monitored remotely by an
installer.
Explanation symbols:
Warning, be aware!
You must carry out this step
Advice
The boiler wires that connect the
boiler to the thermostat should not be
longer than 50 metres and must not
have a greater resistance than 5 Ohm
per wire. If this is the case however, we
advise you to have the wires replaced.
Disconnect the boiler from the
electrical network before you continue
Check the availability and quality of
the WiFi network connection
beforehand, also check if there is a free
power outlet available near the boiler.
Make sure you have the password of
the WiFi network to which you will
connect the boiler gateway.
Keep the short ID and network name
of the boiler gateway at hand. The
short ID is the 8 letter code on the
sticker on the back of the boiler
gateway. The network name starts
with “smile_”. You need both to
connect the boiler gateway to the
WiFi network.
Precautions
and safety
We advice you to have your boiler
gateway installed by the installer of
your central heating system.
The existing boiler wires that connect
the boiler to the thermostat have to be
connected to the OpenTherm
connection of the boiler. You can nd
this information in the manual of your
boiler.
stuvwxyz
ssid: smile_abcdef
Short ID
Network name

11 | Boiler gateway “Adam”
EN
Short ID
Network name
More information The installation
The installation can be described in 2
steps:
1. Connect the boiler gateway to the
(WiFi) network.
2. Connect the boiler gateway to the
wires between the boiler and the
thermostat.
Connect to the network
Do this close the boiler. This way you
ensure the WiFi signal is strong
enough.
Connect the adapter cable to the
adapter and the boiler gateway and
plug the adapter into the wall socket.
Wait until the boiler gateway has
booted up: the upper light and the
light in the middle of the boiler
gateway are blinking slowly.
WiFi via WPS?
WiFi via WPS is only supported via a
special WPS button on the router.
Press the black button on the boiler
gateway for 2 seconds.
Wait until the upper light is blinking
quickly and regularly.
Enable WPS on the WiFi router to
connect to WiFi.
In the package
In the package of the boiler gateway you
will nd:
1. Qupit boiler gateway
2. Wall plate
3. Installation cable to connect to the
boiler
4. USB adapter
5. Adapter cable
6. Installation instruction
7. Installation card (in the back of the
installation instruction)
More information about the Qupit boiler
gateway can be found on our website:
www.getqupit.com/boiler-gateway .

12 | Boiler gateway “Adam”
If after 2 minutes the boiler gateway
has not made a connection yet to
your WiFi network, the boiler
gateway will be recalled to the access
point mode.
WiFi?
Do you want to connect
the boiler gateway to
WiFi and do you have
an Android smartphone
or tablet? Search for the Plugwise
connect app in the Google Playstore.
The app will guide you connecting the
boiler gateway to the WiFi network.
No Android? Follow the next steps to
connect the boiler gateway to the WiFi
network.
Connect your smartphone or tablet
with the WiFi network of the boiler
gateway, starting with “smile_”.
Enter the short ID as your password.
Open the webbrowser on your
smartphone or tablet and go to
http://192.168.40.40. Because you
are connected to the network of the
boiler gateway, you will be redirected
to the network page of the boiler
gateway “Settings” > “Network”.
Press “Scan” and select your own
WiFi network.
Enter the password of your own WiFi
network and save the settings.
Please make sure that you reconnect
your smartphone or tablet to the
WiFi network to which you just
connected the boiler gateway.
Network cable?
Connect a network cable between
the router and the boiler gateway.
Check your network connection?
Use your smartphone or tablet that is
connected to the same network as
the boiler gateway is connected to.
Go to: https://adam.plugwise.net
Use your short ID to log in.
You will be directed to the webpage
of the boiler gateway.
Having trouble via WiFi?
Press the black button on the boiler
gateway for 5 seconds until the light
in the middle has blinked 5 times
and the upper light starts to blink
rapidly.
The network settings will be deleted.
Wait until the boiler gateway has
booted up, then try to connect the
boiler gateway to your WiFi network
again.

13 | Boiler gateway “Adam”
EN
Connect to the boiler
Installation diagram Adam with thermostat
Disconnect the thermostat wire
between the boiler and the
thermostat and replace it with the
extra installation cable for the boiler.
Connect the wires running to the
boiler to the boiler gateway at the
ame icon.
Connect the wires running to the
thermostat to the boiler gateway at
the thermostat icon. You must use the
existing wires to do this.
Determine the position of the boiler
gateway by the boiler and x the wall
plate of the boiler gateway.
Click the boiler gateway onto the wall
plate.
Plug in the boiler again. Plug the boiler
gateway into the power outlet and wait
until the boiler gateway has started up.
Installation diagram Adam with smart
thermostat
Consult the manual of the boiler for
more information about the connector
of the boiler.
Some smart thermostats have a
gateway that is connected to the boiler.
For these installations place the boiler
gateway between the gateway of the
thermostat and the boiler.
Unplug the boiler and the boiler
gateway from the electrical network.

14 | Boiler gateway “Adam”
Open the
webpage
Have you connected the boiler
gateway to the internet? Ensure that
your smartphone or tablet is
connected to the same network as to
which you have connected the boiler
gateway
Go to https://adam.plugwise.net
Use your short ID to log in.
You will be directed to the webpage
of the boiler gateway. Here you can
adjust the room temperature, set a
schedule and have insight into your
heating behaviour using graphs.
The LED
behaviour
In the table below the most important
behaviour of the LED’s is described.
LED Colour Pattern Description
Green Blink slowly The boiler gateway is in access point mode
Green Blinking Communication with the wi network
Green Blinking Boiler gateway state
Green Blinking Communication with the LAN network


Plugwise B.V.
Wattstraat 56
2171 TR Sassenheim
The Netherlands
www.plugwise.com
Support: www.plugwise.com/technical-contact
installation information
Gateway
Short ID:
Installer
Name:
Phone number:
Website:
This manual suits for next models
1
Table of contents
Languages:
Popular Gateway manuals by other brands

GateWay Fax Systems
GateWay Fax Systems Easy-Fax 90si user guide

2N Telekomunikace
2N Telekomunikace ATEUS EasyGate 501300E quick start

IAI
IAI RCM-GW-PR Operation manual

Bosch
Bosch Conettix D6600 Operation and installation guide

Moxa Technologies
Moxa Technologies NPort 5600-8-DTL Series Quick installation guide

Kronback Tracers
Kronback Tracers NDR user manual

Technicolor
Technicolor TD5130 Setup & user guide

US Robotics
US Robotics USR9108 - U.S. Robotics Wireless MAXg Specifications

IXXAT
IXXAT CANio 250 Quick start manual

WELLTECH
WELLTECH FXS H.323 GATEWAY 1AFXS manual

D-Link
D-Link Airspot DSA-3100 Quick installation guide

Qvidium
Qvidium Pro-MPEG DVB-ASI Gateway quick start guide