RAB ProRak 26 User manual

ProRak
MULTIBOARD
CONSOLE

ProRak
MULTIBOARD
CONSOLE
A4 A3
A1
A2 A2
A4A3
A1
A2A2
C1
C6
C5
C4
C3
C2
B6 B6
B1 B1
B2
B3 B3 B4 B5
Keyboard Tray
Do not contact your vendor, please visit
www.RABAudio.com/contact-us for parts and services.
Rack Screws Confirmat Screws Rubber Pads
PARTS LIST DESCRIPTION
2 A1 Feet
4 A2 Pedestal Spacer
2 A3 Pedestal Front
2 A4 Pedestal Back
2 B1
2 B2 Outer Rack Vertical
2 B3 Speaker Shelf
2 B4 Armrest Top
2 B5 Armrest Front
2 B6 Armrest Angle
B7 B4, B5, and B6 Combined
1 C1 Center Brace
1 C2, C3, C4 Cable Trough
1 C5 Monitor Shelf
1 C6 Mixer Bed
1 Keyboard Tray
4 10U Rack Rails
4 4U Rack Rails
303/4" Black Screws
1 Keyboard Slide Set
97Confirmat Screws Multiboard 36
94Confirmat Screws Multiboard 26
2 Rubber Pads
16 10-32 Rack Screws for Mounting Gear
TOOL LIST
1 4mm Allen Key
1 Hex Bit
B2
Tray Slides
Tray Mounting Slides
Inner Rack Vertical
w/Keyboard Slider
6Silver Tray Screws

ProRak
MULTIBOARD
CONSOLE
STEP 1 of 6
Tools required: 4MM Allen Wrench
1. The pedestal pieces are A1, A2, A3 and A4 as shown in the picture.
2. Attach A2 to A1 with bumper molding facing upwards.
Note: The bottom of A1 will have a recessed hole where the confi rmat
screw will rest.
3. Attach A3 to A2.
4. Attach A4 to A2.
STEP 2 of 6
Tools required: 4MM Allen Wrench + Phillips Head Screwdriver
1. The pieces are B1, B2, 10U rack rails(4), 4U rack rails(4), 3/4"
black screws, keyboard tray slides, and the completed pedestals
from Step 1.
2. Attach the 10U rack rails and 4U rack rails to the predrilled holes
on B1 and B2 with 3/4" black screws. Place B2 aside until step 5.
3. Remove the mounting slides & attach the two tray slides to the
predrilled holes on B1 with 3/4" black screws. The front of the
slides need a one inch gap between the slide and bumper molding.
4. Attach B1 to A3 and A4.
5. Make sure the tray slides face each other.
6. The finished pieces will not stand on their own. Either lean against a
wall or lay on the ground for now.
A4 A3
A1
A2 A2
A4A3
A1
A2A2
A4
A3
A1
A2
A2
A4
A3
A1
A2 A2
B1 B1
Rack Screws
Confirmat Screws
Rubber Pads
Rack Screws Rubber Pads
NOTE: Only hand tighten the Confi rmat screws.
You will do a fi nal tightening in the last step.
Place rack rails over these holes on B1
and B2 with a two hole gap
Place keyboard slides over these
holes with a one inch gap between
the slide and bumper molding
B1
B2
B2
.
.
.
.

ProRak
MULTIBOARD
CONSOLE
STEP 3 of 6
Tools required: 4MM Allen Wrench
1. The pieces are rubber pads, C1, C2, C3, C4, C5 and C6.
2. Attach C1 to both B1s.
3. Attach C2 to C3.
4. Attach C4 to C3 completing the cable trough. Attach the cable trough to
both B1s.
5. Attach C5 to C4.
6. Attach C5 to both B1s.
7. Attach C6 to both B1s then insert the rubber pads into C6.
8. Tighten all the confirmat screws in both B1s but be careful you do not want
to over t ighten them.
Use diagram below for detailed layout schematic of pieces.
NOTE: Only hand tighten the Confirmat screws.
You will do a fi nal tightening in the last step.
C1
C6
C5
C4
C3
C2
B3
C5
C3
C2
C4 B7
C6
A3
A4
C1
Rack Screws
Confirmat Screws
Rubber Pads

ProRak
MULTIBOARD
CONSOLE
STEP 5 of 6
Tools required: 4MM Allen Wrench
1. The pieces are B4, B5 and B6.
2. Slide B4 into B6.
3. Slide B5 into B6. Now you have completed B7.
STEP 6 of 6
Tools required: 4MM Allen Wrench
1. Grab pieces B2, B3, B7, and keyboard tray.
2. Attach B3 to B1.
3. Attach B7 to B1.
4. Attach B2 to A3, A4, B3 and B7.
5. Slide keyboard tray into the keyboard slides.
6. Double check all your confirmat screws are tightened into your Multiboard.
B5
B6
B4 Combined
makes B7
B4
B5
B7 B7
B2 B2
B3 B3
Rack Screws
Confirmat Screws
Rubber Pads
NOTE: Do all your final tightening and enjoy.
Weight ratings for each B3 is 40lbs MAX
STEP 4 of 6
Tools required: Phillips Head Screwdriver
1. Grab silver screws(6), mounting slides, and keyboard tray.
2. To attach the mounting slides lay your keyboard tray on a flat
surface and insert the six silver screws into the holes shown in
the diagram.
3. The holes on the keyboard tray line up to the vertical
adjustment holes on the mounting slides so you can adjust to
the correct position accordingly.

1507 S. Olive St. South Bend, In. 46619
www.rabaudio.com

Please note before loading your gear!
You may feel a slight resistance for the first 2-3 turns when inserting your 10-32 thread
screws into the Rack Rails. This is due to the powder coating process on the Rack Rail
itself, after 2-3 turns the coating will clear from the thread & turn freely.
FOR PROMPT SERVICE & PARTS PLEASE
DO NOT CONTACT YOUR VENDOR
please visit www.RABAudio.com/contactus
Visual assembly coming soon.