1. Aer pairing, press the rates buon to switch between high rates (3 beeps) normal rates (2 beeps)
and low rates (1 beep). First flights should be in normal or low rates before advancing to high rates.
2. Press the buon with the One Buon Take-Off symbol the HoverJet will take off and hover at about 3’
above the floor.
3. Move the throle (le sck) upward and downward to control the ascent or descent, move the steering
(right sck) to control the flight direcon.
4. Move the throle (le sck) le or right and the HoverJet will rotate (yaw) le/right accordingly.
5. Press the One Buon Take-Off buon again or move the throle sck down gradually to land.
6. When your finished flying, turn off the HoverJet and the transmier.
Cauon：To avoid injury to the pilot or damage to the drone, move the throle smoothly and not too fast.
Flying Your HoverJet
The 4 propellers are not idencal. Each propeller
is labeled with an A or B.When installing replacement
propellers, be certain to insatll the A/B in the correct locaon.
IF needed, use pliers to gently pull the damaged propeller
off the sha.
Warning：To avoid damage to people or aircra, check
propellers for damage before
each flight. Also, ensure that the
propellers are firmly pressed on
to the sha. Replace any propeller
that shows damage and use only
the provided propellers or
idencal replacements. Do not
modify the provided propellers.
Replacing Damaged Propellers
• Do not dispose of the Li-Po baery into a fire.
• Never place the product on a hot surface.
• Keep the product in dry and cool environment.
• Use only provided USB cable for charging.
Charge the baery per the manual instrucons.
• Do not use type of sharp object to insert the Li-Po
baery to avoid puncture.
• Charge the Li-Po baery every 6 months if not in
regular use.
• Turn off the power when the product is not in use.
Warnings
Geng Ready to Fly
1. Press the On/Off buon unl the LED flashes.
2. Place the HoverJet on a level surface.
3. Press the On/Off buon of transmier,
the LED should flash and the transmier should beep.
4. Move the throle all the way up then back to middle
posion to pair the airplane and transmier. If pairing is
successful, the transmier will beep 2 mes and the LED on
both transmier and airplane stop flashing and remain on.
Note: If pairing fails, turn off airplane and transmier,
repeat above steps, or move to another place to avoid
electromagnec interference.
Calibrang Your HoverJet
1. Aer pairing, put the HoverJet on a level surface.
Move the throle sck down and the steering sck up
at the same me and hold them in place, the
LED’s should then flash on and
off for about three seconds.
2. When LED’s stop flashing
the calibraon is complete.
The HoverJet should now
maintain a steady hover and
fly smoothly. If not, the
controls need to be adjusted
using the trim buons- see that secon for instrucons.
Warning:
CHOKING HAZARD--
Small Parts Not For
Children Under 3 Years
Made in China
A
A
B
B
1. Press( ) button, the transmitter will beep constantly.
2. Move the steering (right stick) to perform flips.
⊙ Front Flip：Move the steering foward (up).
⊙ Back Flip：Move the steering backward (down).
⊙ Left Flip：Move the steering left.
⊙ Right Flip：Move the steering right.
3. After completing a flip, the HoverJet will exit flip stunt mode.
If you want to exit flip stunt mode afterpressing the button,
push in the throttle control stick.
Note：* To avoid hitting people or other objects, please ensure
there is enough space before performing flips.
Compleng Flips Trimming Your HoverJet
· Push the throle forward and observe how the
aircra reacts.
• Trim forward/backward: If the aircra tends to dri
forward, press( ) unl aircra hovers; if it tends to
dri backward, press ( ) unl aircra hovers.
• Trim le/right: If the aircra tends to dri le,
press ( ) unl aircra hovers, if it tends to dri le,
press ( )unl aircra hovers.
Note: The transmier beeps when you press a
trim control but stops beeping when you reach
maximum trim adjustment.
Hover Jet
32
