Rack furniture CHARLESTON LOFT BED User manual

CHARLESTON
LOFT BED
Made in Malaysia PRN: AIM-36-1001-RAC [11.03.17]
Rack Furniture
Suite 1, 2713 SE I Street, Bentonville, AR 72712 USA
Customer Service: 1-479-715-6445
www.rackfurniturellc.com
Thank you for choosing Rack Furniture. Before starting, we suggest
reading through this instruction manual to ensure that you completely
understand the assembly of this product.

WARNING
Two people will be required to assemble this unit.
Care and Maintenance:
To clean, use only mild household soap and warm water. Do not use bleach or
detergent. Do not use abrasive cleaners which can scratch the finish of the product.
Use clean soft cloths to wash, rinse and dry. With proper care, the quality finish will last
a long time. Wood surfaces may be treated with light application of a good grade of
non-toxic furniture polish.
Safety First: Ensure that the top mattress fitted to this bed is no higher than the warning
label attached to the safety rail assembly. IE: 6.30in (160mm) below the top of the safety rails.
Please note: Top bed is not recommended for children under six (6) years old.
!Allowing children to play on or below the beds is dangerous and jumping under any
circumstances should be prohibited!
!The ladder is provided to allow easy access to the bed. Do Not allow children to get to the
bed any other way.
!Ensure that you check regularly that all bolts are securely fastened and all components are
in place. If spare parts are required, contact Rack Furniture at 1-479-715-6445 or write to us
at 2713 SE I Street Bentonville, Arkansas 72712.
!Do not use product if any parts are missing.
!Do not use substitute parts.
Keep these instructions in a safe place for future use.
Caution: There are many small components used in the construction of this unit. These
loose items should be kept away from young children while assembling your unit. As an
extra precaution, screw cover caps should be permanently fixed in position. (Where
applicable).
Tools required for Assembly:
DO NOT USE POWER TOOLS
TO ASSEMBLE THIS PRODUCT.
USE OF POWER TOOLS WILL
INVALIDATE ANY CLAIM AND
MAY DAMAGE THIS PRODUCT
MAKING IT UNSAFE.
Rubber Hammer Phillips Screwdriver
Page 2 of 32

PART LIST
Page 3 of 32
Carton 2 of 3
Pcs
Part Name
No.
Back Panel 1
Left Panel (Cabinet) 1
Plinth Panel (Front) 1
6Support Panel 1
3
Plinth Panel (Side) 1
5
10
12
Plinth Panel (Cabinet) 1
13
Bottom Panel (Cabinet) 1
14
Back Support Panel (Cabinet) 1
15
Support Panel (Cabinet) 2
16
Top Panel (Cabinet) 1
17
Right Panel (Cabinet)
Back Panel (Drawers)
1
3
19
20
Left Panel (Drawers) 3
21
Right Panel (Drawers) 3
22
Bottom Panel (Drawers) 3
23
Support Panel (Desk)
Center Panel
2
1
1
26
30
Front Panel (Drawers) 3
24
Center Panel 1
1
Bottom Panel 1
4
Top Panel 1
11
Back Panel (Desk) 1
27
Right Panel 1
7
Left Panel 1
8
Top Panel (Desk) 1
28
Front Panel (Right) 1
29
Back Panel (Right) 1
31
Back Panel (Left) 1
32
Front Panel (Left) 1
35
Back Panel (Cabinet) 1
18
Center Panel 1
2
Front Panel (Desk) 1
25
Pcs
Part Name
No.
Carton 1 of 3
PcsPart Name
No.
Carton 3 of 3
Side Rail (Front) 1
42
Side Rail (Rear)
K/D Slat Base
Guardrail (Long)
Guardrail (Short)
1
18
1
1
43
44
45
46
Brace
Ladder
2
1
47
48
Center Panel (Left)(Bottom)
Support Panel
Support Panel (Shelf)
1
2
34
36
39
Door 1
40
Movable Panel 1
41
Back Panel (Shelf) 1
37
Bottom Panel (Shelf) 1
38
Support Panel 1
9
Center Panel (Left) 1
33

PART LIST
Sticker
Date Code
25
26
26
27
28
20 x3
21 x3
22 x3
23 x3
24 x3
13
14 15
16
16
12
19
17
18
1
2
3
4
5
6
7
11
10
30
29
31
35
33
34
32
9
8
36
37
38
39
41
40
43
42
44 x18 45
46
47 x2
48
Page 4 of 32
Sticker Date Code
(Back side)
Sticker Date Code
(Back side)

HARDWARE LIST
Part Name
No. Pcs
A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
Q
R
S
T
U
V
W
X
Y
Z
Z1
Z2
Z3
Z4
46
62
22
5
10
2
1
2
5
4
4
4
4
4
4
1
3
3
1
38
4
1
8
16
2
1
132
3 Set
25
Page 5 of 32
2
Z5
Cam Bolt
Cam Lock
45mm Chipboard Screw
Solid Aluminum Handle (silver)
20mm Handle Screw
PVC Door Spring
Magnet
30mm Chipboard Screw
M6 x 25mm Allen Bolt (Silver)
U Shape Casters (Black)
Dome Locking Nut (Black)
25mm Allen Bolt (Black)
Metal Shelf Support
M8 x 95mm Allen Bolt (Black)
M8 Round Nut
M6 x 80mm Allen Bolt (Silver)
M6 x 70mm Allen Bolt (Silver)
M6 x 60mm Allen Bolt (Black)
M6 x 50mm Allen Bolt (Silver)
M6 x 30mm Allen Bolt (Silver)
M6 x 12mm Allen Bolt (Silver)
M6 JCN Nut (Silver)
Double Ended Dowel
Sitcker
M6 Allen Wrench
M8 Allen Wrench
M8 x 25mm PVC Dowel
14” Drawer Slide(Black)
15mm Chipboard Screw
M6 JCN Nut (Black)

Page 6 of 32
Z4 Z3 The Last Hole
The First Small Hole
FRONT BACK
How to correctly install Cam Bolt and Lock
To secure simply turn the cam lock 180 Degrees
in a clockwise direction, or until tight.
5
When fitting cam bolts into holes ensure that the
arrow on the top of the cam points to the
intersecting hole, which is usually on the nearest
end edge of the panel.
1
Cam Lock Cam Bolt Hole
To fit two panels together the cam lock will slide
into the intersecting hole, and into the cam.
2
B
Insert Cam Bolt into Cam Lock hole. If Cam Bolt
does not slide all the way in, check to make sure
arrow on cam Lock is pointing toward cam bolt
hole.
4
B
3
Screw in
Cam Bolt
tight.
INTERSECTING HOLE
Cam Lock arrow facing
towards the hole.
B
Cam Lock
B
INTERSECTING HOLE
Cam Bolt
A
A
A
B5a4a
To Assembly the Drawer Slide, Please Follow Step as Below

STEP 1 - DESK ASSEMBLY
Page 7 of 32
(x4)
J
(x8)
A (x8) B
(x4)
L
(x1)
D
(x2)
E
Hardware needed to assemble the Desk
(x14)
Z2
(x4)
K
25
26
26
27
28
Sticker
Date Code

STEP 1 - DESK ASSEMBLY
1-1
Page 8 of 32
Slide board (25) onto cam stud with board (26), make
sure both boards are flush. With screw driver turn cam
180° to lock. Repeat with second board (26).
1-1a
25
26
26
26
25
Assemble the wood dowels, cam locks and cam Bolts first as per the diagram below.
27
Z2
Z2
Z2
A
B
BA
Z2
26
x2
B
B
Z2
25
A
AA
A
28
B
B
A
A
Z2
Z2

STEP 1 - DESK ASSEMBLY
Page 9 of 32
1-2
1-3
1-4
25
1-4a
L
K
J
25
27
Attach caster (J) with allen bolt (L) and nut (K) as shown.
Repeat assembly for 3 other casters, two on each end.
Note: Locking Castors on the Front (Panel 25).
Slide board (28) into board (25) and onto board (27).
Tighten all 4 cam locks 180°.
25
28
27
1-3a
28
27
Slide board (27) onto both (26) boards then tighten both
cams by turning 180°.
27
26
26
1-2a
26
27
Sticker
Date Code

STEP 1 - DESK ASSEMBLY
STEP 2 - DRAWER AND CABINET ASSEMBLY
Page 10 of 32
Hardware needed to assemble the Drawer and Cabinet
Attach handle (D) with handle screw (E) to front
panel (25) as shown. Desk assembly complete.
1-5
25
1-5a
25
D
E
E
13
14 15
16
16
12
19
17
18
20 x3
21 x3
22 x3
23 x3
24 x3
(x25)
A(x24)
B(x48)
Z2
(x3)
D
(x6)
E(x25) Z4
(3 set)
Z3

STEP 2 - DRAWER & DRESSER ASSEMBLY
Assemble the wood dowels, cam locks and cam Bolts first as per the diagram below.
17
Z2
Z2
Z2
Z2
B
B
B
B
12
A
A
A
A
A
A
A
12
19
A
A
A
A
A
A
13
Z2
Z2
Z2
Z2
Z2
Z2 B
B15 B
B
Z2
Z2
16 x2
Z2
Z2 B
B
14
24 x3
20 x3
B
Z2
B
Z2
TURN OVER
21 x3
A
Z2
B
21 x3
TURN OVER
22 x3
A
Z2
22 x3
B
Page 11 of 32
A
A

STEP 2 - DRAWER AND CABINET ASSEMBLY
Page 12 of 32
Tighten back panel (20) with side panel (21 &
22) as shown. Make sure back panel with cams is
facing out. Once cam bolt is slid into cam lock
then then turn cam lock 180° or until locked.
Insert bottom panel (23) as shown.
Insert (24) on to drawer, make sure all holes
line up and tighten cams by turning 180° or
until tight.
2-1
2-2
2-3
2-1a
20
21
22
20
22
23
24
24
21
22
21
2-3a

Page 13 of 32
STEP 2 - DRAWER & DRESSER ASSEMBLY
Attach (13) to bottom of (14). Put (14),(15) and both (16)’s in (19). Make sure all the cam locks face
down or towards back of unit, then tighten.
14
15
16
2-6 2-6a 2-6b
2-5 Fixing drawer slide (Z3) with Screw (Z4) as
shown.
Z4
Last third hole
Third Hole
Back
Front
Z3 Z4
Z3
Z3
21
22
23
Z4
Z4
Z4
Z4
Tighten handle (D) with screw (E) as shown.
Repeat steps #1-4 on the two remaining
drawers.
24
24
24
D
E
2-4
2-4a
13
14
19

STEP 2 - DRAWER & DRESSER ASSEMBLY
Page 14 of 32
2-9
2-8
2-7
17
19
19
17
A
B
Place (17) onto unit and tighten.
Insert back panel (18) into channels as
shown.
18
Make sure all cam studs line up. Tighten
right panel (12) as shown, repeat for left
panel (19). Dresser assembly complete.
2-9a
12
14
13
12
14 13
16 16
17
19
15

STEP 3 - SHELF ASSEMBLY
Page 15 of 32
3
1
2
4
5
6
7
11
10
9
8
41
40
Hardware needed to assemble the Shelf
(x6)
A(x6)
B(x31)
Z2 (x15)
C

Page 16 of 32
STEP 3 - SHELF ASSEMBLY
Assemble the wood dowels, cam locks and cam Bolts first as per the diagram below.
10 9
11
7
A
8
Z2
Z2
Z2
A
11
TURN OVER
A
Z2
Z2
Z2
Z2
Z2
Z2 A
4
Z2
Z2
Z2
B
B
A
2
Z2
B
B
B
Z2
Z2
Z2
3
Z2
Z2
A
65
Z2
B
Z2
Z2
Z2
Z2
Z2
Z2

Page 17 of 32
STEP 3 - SHELF ASSEMBLY
3
Tighten panel (2) to panel (1) as shown. Then tighten
panel (3) as shown.
2
1
3
2
3-1a
2
1
3-1b
Tighten bottom panel (4) with screw (C) as shown.
3
1
4
3
4
C
3-2
3-2a
3-1
C
C

STEP 3 - SHELF ASSEMBLY
Page 18 of 32
3-3
Push in panel (6) to the panel (5) as shown in 3-3a.
Push in panel (5 & 6) into bottom of panel (4). Then tighten to bottom panel as shown
3-3b & 3-3c.
3-3a 3-3b 3-3c
5
6
5
6
5
64
45
5
6
4
5
7
4
4
5
7
Tighten panel (7) as shown.
3-4a
3-4

STEP 3 - SHELF ASSEMBLY
Page 19 of 32
3-6
3-5
Push in back panel (10) as shown. Then tighten support panel (9) with screw (C) as shown.
10
9
9
C
7
7
3-5a
11
7
11
C
C
1
3
3
11
C
Attach panel (11) onto unit. Make sure all dowels are inserted and the panel is flush with unit.
Secure with screws (C) as shown.
3-6a
3-6b
7
(x5)
C
(x2)
C
C
C

STEP 3 - SHELF ASSEMBLY
STEP 4 - BED ASSEMBLY
Page 20 of 32
Sticker
Date Code
30
29
31
35
33
34
32
36
37
38
39
43
42
44 x18 45
46
47 x2
48
UP
Tighten panel (8) with screw (C) as shown.
Shelf assembly complete.
3-7
8
6
11
8
C
6
3-7a
4
4
C
C
CC
Sticker Date Code
(Back Side)
(x9)
C