RACKS-N-CABINETS 2393-60DW User manual

SPARTAK ENTERPRISES, INC.
SWIVEL MEDIA TOWER
Model #2393-60DW
LOT #2780
IF PARTS ARE MISSING AND OR DEFECTIVE, IF INSTRUCTIONS ARE NOT CLEAR
OR IF YOU ARE EXPERIENCING PROBLEMS ASSEMBLING OUR PRODUCT.
BEFORE YOU RETURN THE PRODUCT TO THE STORE,
PLEASE CALL US TOLL FREE FOR CUSTOMER SERVICE ASSISTANCE
[phone]
OR SEND US EMAIL AT
[email protected]
PLEASE HAVE ITEM NUMBER READY, AND A REPRESENTATIVE WILL GLADLY ASSIST YOU
SPARTAK ENTERPRISES, INC. 841 E. FRANCIS STR. ONTARIO, CA. 91761 TEL; 951/360-0610 FAX; 951/360-0775
RACKS-N-CABINETS
[email protected]
RACKS-N-CABINETS. 11186 VENTURE DR. MIRA LOMA,CA 91752 TEL: [phone] FAX: [phone]

CCPZXX
CAMLT12
CAMBT16
BM25
SPE610BL
BPXX54
TRNTPL
TRNTSC
DOWW830
CAMLOCK COVER CAP
CAMLOCK
BOLT
BRACKET ANGLE
EURO SCREW
SHELF SUPPORT
SWIVEL PLATE
SWIVEL BOLT
WOOD DOWEL
HARDWARE PART # DESCRIPTION QTY
16
16
16
8
16
180
1
1
4
TOOL REQUIRED
PHILLIPS SCREWDRIVER HAMMER

ABC
D
E
F
NOTE: FIRST MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED ON THIS SHEET. IF YOU ARE MISSING ANY PIECE(S), DO NOT
ASSEMBLE THE UNIT. INSTEAD, CALL OUR CUSTOMER SERVICE NUMBER AT: [phone]. WE WILL BE HAPPY TO ASSIST YOU.
2393A-Top
2393B-Bottom
2393C-Base
PARTS ARE USUALLY MARKED ON THE RAW EDGE
1pc
1pc
1pc
2393D-Divider
2390E-Face Panel
2393F-Adjustable Shelf
4pcs
4pcs
36pcs

1
E
CAMLT12
UNLOCKED
POSITION
SPE610BL
BM25
Use small hole #6
from the left end.
Use small hole #4
from the right end.
Do not tighten screw on the angle bracket all the way in
this step. Leave it a bit loose until you attach part D in
the next step. Then you will tighten the screws.

2
D
E
D
E
Repeat steps 1 and 2 for the remaining three sets of part (D) & (E)
SPE610BL
Press part (D) in the groove of part (E). Make sure part (E) and (D) are
aligned with each other on both ends and RED and BLUE marked
ends are on the same side.
1) loosen the screw on the angle bracket attached to board E,
2) line up angle bracket hole with board D and attach screw
into bracket and hole on board D,
3) tighten screws on boards D and E until both
board are pulled together and fit properly.
If you experience difficulty in lining up boards E and D with the angle
brackets, try the following:

3
B
CAMBT16
A
B
C
TRNTSC
TRNTPL
DOWW830
Top Side
1 2
3

4
Turn camlocks clockwise
using flat (preferred) or
phillips scrudriver until full
stop(slightly over12a turn
to lock the bolt)
12
34
Lock camlocks on panels E as
you install them before you
proceed to next one.
Otherwise panels may fall over
and cause damage. Make sure
you have on top only RED
marked ends of panels D & E

5
A
Turn camlocks
clockwise until
full stop (slightly
over12a turn to
lock the bolt)
BPBL54
CCPZXX
If you'd like to optimize the space for CD or DVD/VHS
only, then use these holes (counting from the top):
CD 1 3 5 6 8 10 11 12 14 -10 spaces DVD/vhs 2 4 6 8 10 12 -7 spaces
or you can use CD or DVD/VHS case as a template to locate the holes. If you skip a hole or
mix CD or DVD/VHS in one section you may end up with unused space at the end
Install top first. Next install one shelf in the middle
(hole#8) on each side to restrict movement of inside
dividers D. Do not tap with hammer onto shelf
supports, instead twist them when inserting in.