Radiall Commercial SMA Series Instruction Manual

TECHNICAL DATA SHEET
1 / 4
SOLDER JACK RECEPTACLE R125.630.170
HERMETIC - WITH CYLINDRICAL CONTACT
Series : SMA
Issue : 0431 B
In the effort to improve our products, we reserve the right to make changes judged to be
necessary.
All dimensions are in mm.
..
pn ao
COMPONENTS
BODY
CENTER CONTACT
OUTER CONTACT
INSULATOR
GASKET
OTHERS PARTS
-
-
MATERIALS
FERRO-NICKEL
DILVER P
-
PTFE
-
-
-
-
PLATINGS ( µm )
GOLD 0.5 OVER NICKEL 2
GOLD 0.5 OVER NICKEL 2
-
-
-
-

TECHNICAL DATA SHEET
2 / 4
SOLDER JACK RECEPTACLE R125.630.170
HERMETIC - WITH CYLINDRICAL CONTACT
Series : SMA
Issue : 0431 B
In the effort to improve our products, we reserve the right to make changes judged to be
necessary.
PACKAGING SPECIFICATION
S
tandard
U
nit
O
ther
1
-
C
ontact us
E
LECTRICAL CHARACTERISTICS
E
NVIRONMENTAL
I
mpedance
5
0Ω
O
perating temperature
-
40/+100
°
C
F
requency
0
-18
G
Hz
H
ermetic seal
1
0-5
A
tm.cm3/s
V
SWR
*
*
+
0
.000
x
F(
G
Hz) Maxi
P
anel leakage
N
A
I
nsertion loss
0
.3*
√
F
(
G
Hz) dB Maxi
R
F leakage - (
N
A
- F(GHz)) dB mini
V
oltage rating
5
00
V
eff Maxi
D
ielectric withstanding voltage
1
000
V
eff mini
I
nsulation resistance
5
000
M
Ω mini
O
THERS CHARACTERISTICS
Assembly instruction
O
thers
:
* See page 3
M
ECHANICAL CHARACTERISTICS
C
enter contact retention
Axial force – Mating end
2
7N mini
Axial force – Opposite end
2
7N mini
Torque
N
AN.cm mini
R
ecommended torque
Mating
N
AN.cm
Panel nut
N
AN.cm
M
ating life
5
00
C
ycles mini
W
eight
1
.200
g

TECHNICAL DATA SHEET
3 / 4
SOLDER JACK RECEPTACLE R125.630.170
HERMETIC - WITH CYLINDRICAL CONTACT
Series : SMA
Issue : 0431 B
In the effort to improve our products, we reserve the right to make changes judged to be
necessary.
RECOMMENDED MOUNTING HOLE DETAIL
PANEL WITH THROUGH HOLE
Frequency range 0 – 18 GHz
VSWR < 1.10 + 0.03 F
PANEL WITH BLIND HOLE
Frequency range 0 – 18 GHz
VSWR < 1.05+0.02F

TECHNICAL DATA SHEET
4 / 4
SOLDER JACK RECEPTACLE R125.630.170
HERMETIC - WITH CYLINDRICAL CONTACT
Series : SMA
Issue : 0431 B
In the effort to improve our products, we reserve the right to make changes judged to be
necessary.
MOUNTING INSTRUCTIONS
1 – Degrease and clean connector and box.
2 –Solder the connector on the panel:
Preheating at about 100°c.
Take care not to exceed 250°c during solder operation .
3 –Solder the pin on the track:
-ceramic substrates: preheating at about 100°c.
-other substrates: no preheating required.
NOTE: Please use a small soldering iron ,or hot air soldering system.
4-Mount the insulator in accordance with the drawing:
used the dielectric insert tool and the dielectric plunger R282.730.043.