Radio Pulse MG2475-RDK User manual

www.radiopulse.co.kr
[MG2475-RDK]
Getting Started
(No. ASW1008)
V0.96

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:2/31
www.radiopulse.co.kr
REVISION HISTORY
Version
Date
Description
VER.0.91
2015.05.12
The Beta version release.
VER.0.92
2015.05.15
Images font modified.
VER.0.93
2015.05.21
Contents link modified.
VER.0.94
2015.05.29
HEX file name modified.
VER.0.95
2015.05.29
RCS image modified.
VER.0.96
2015.06.03
Fix Typo.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:3/31
www.radiopulse.co.kr
CONTENTS
1. INTRODUCTION................................................................................................................................... 4
2. REFERENCE ........................................................................................................................................... 5
[R1] ADT0007-Remote Controller-Simulator User's Guide_V1 0.pdf..........................................................5
[R2] ADT0002-Device Programmer MD User's Guide_En_V2 2.pdf ............................................................5
3. DEFINITIONS ........................................................................................................................................ 6
4. KIT CONTENTS..................................................................................................................................... 7
5. QUICK START GUIDE .......................................................................................................................... 8
5.1. MG2475-DONGLE(TARGET)TO RDB(CONTROLLER) .............................................................................................8
5.1.1. Usage of MG2475-Dongle ..........................................................................................................................8
5.1.2. Usage of RDB ....................................................................................................................................................9
5.2. MG2470-EVB(TARGET)TO RDB(CONTROLLER):OPERATING WITH RC-SIMULATOR.................................. 15
5.2.1. Usage of Remote Controller-Simulator .............................................................................................. 15
5.2.2. Usage of RDB ................................................................................................................................................. 18
5.3. MG2475-DONGLE(TARGET)TO RCU(CONTROLLER) .......................................................................................... 20
5.3.1. Usage of MG2475-Dongle ....................................................................................................................... 20
5.3.2. Usage of RCU ................................................................................................................................................. 21
APPENDIX A. FIRMWARE DOWNLOAD. ............................................................................................... 23
CP210X DRIVER INSTALLATION..................................................................................................................................... 23
CHECK COM PORT............................................................................................................................................................... 25
FIRMWARE DOWNLOAD .................................................................................................................................................. 27
APPENDIX B. OPERATING WITH RDB-RDB ......................................................................................... 28
OPERATION................................................................................................................................................................................. 28
PAIRING (CONTROLLER &TARGET) ........................................................................................................................................ 28
VOICE:CONNECT (ONLY CONTROLLER)................................................................................................................................ 29
VOICE:DISCONNECT (ONLY CONTROLLER).......................................................................................................................... 29
APPENDIX C. USAGE OF MG2470B-RDB KEY SCAN.......................................................................... 30
KEY MAPPING –FUNCTION MODE ......................................................................................................................................... 30

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:4/31
www.radiopulse.co.kr
1. INTRODUCTION
MG2475-RDK (Remote Controller Development Kit) is the development kit based on
MG2475 which is an SOC chip including RF transceiver and 8051 micro controller, by
RadioPulse.
This document explains how to start with MG2475-RDK.
Additionally, this document includes like below;
- How to install CP210X driver
- How to download the firmware using RadioPulse Device Programmer
- How to use Remote Controller Simulator.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:5/31
www.radiopulse.co.kr
2. REFERENCE
[R1] ADT0007-Remote Controller-Simulator User's Guide_V1 0.pdf
[R2] ADT0002-Device Programmer MD User's Guide_En_V2 2.pdf

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:6/31
www.radiopulse.co.kr
3. DEFINITIONS
MG2475: 2.4GHz RF Transceiver Chip in SoC type developed by RadioPulse,
applied to ZigBee, IEEE802.15.4-2003, 2006.
MG2475-Dongle: ‘RF to USB Bridge Controller’ module in USB dongle type which is
connected to Host. It connects RF communication and USB communication.
RDB: Remote controller Development Board.
LM2475-C: Chip antenna type module for MG2470 RDK.
MG2470-EVB(Evaluation Board): a PC interface board of LM2475-EM. This board
makes it possible to download user programs to LM2475-EM or connect LM2475-
EM to host programs in PC system.
LM2475-EM(Evaluation Module): 2.4GHz ZigBee Module embedded with MG2475.
It is applied to ZigBee 200X, IEEE802.15.4.
CP210x Device Driver: Device Driver Program to connect MG2470B-RDB /
MG2470-EVB to PC by USB cable. In installation procedure of Device Programmer
MD, CP210x Device Driver installation is automatically questioned. A user can install
it then.
Target: The receiver which is connected with Remote Controller Simulator.
Controller : Remote Controller
Device Programmer MD: a PC GUI program for firmware downloading provided by
RadioPulse. It is used to update the firmware for LM2475-C and MG2475-Dongle.
MG2470-GS-MPU6150: 6-axis Motion Tracking Module(3-axis gyroscope, 3-axis
accelerometer)
MG2470-TP-TC30Q: Touch pad module embedded with 8bit MCU(TC30Q) including
touch sensor of Coreriver

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:7/31
www.radiopulse.co.kr
4. Kit Contents
Remote Controller Development Board (MG2470B-RDB) with MG2475 Chip
antenna type module(LM2475-C) and Touch pad module (MG2470-TP-TC30Q)
Remote Controller Development Board (MG2470B-RDB) with MG2475 Chip
antenna type module(LM2475-C) and Gyro Sensor module (Mg2470-GS-MPU6150)
MG2470 evaluation Board(MG2470-EVB) with MG2475 evaluation module(LM2475-
EM) and +2dBi Antenna
MG2475-Dongle x 2
MG2475-RCU
MG2475 ZigBee Single Chip x 25
USB ISP Downloader and cable for MG2475-Dongle x 2
USB Cables
(USB 2.0 Cable (A-B) x 1, MINI USB 2.0 Cable (USB 2.0 A/M To Mini USB 5PIN) x2)
Software CD
Note: Provide Gyro hardware, but Gyro software and LIB not included.
Please contact the sales division for information of Gyro software and LIB.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:8/31
www.radiopulse.co.kr
5. Quick start guide
5.1. MG2475-Dongle(Target) to RDB(Controller)
MG2475-Dongle and RDB firmware are already downloaded.
Each firmware file is like below;
- MG2475-Dongle : MG2475_RdkTarget_DONGLE.hex
in [Package CD\0. Getting Started Manual\Firmware\]
- RDB : MG2475_RdkController.hex
in [Package CD\0. Getting Started Manual\Firmware\]
5.1.1. Usage of MG2475-Dongle
Install MG2475-Dongle
Enter the pairing mode
** Pairing mode will remain 30 seconds.
* Status LED
On: Already Paired
Off: Un-pair
Toggle: Pairing mode
* Pairing Button

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:9/31
www.radiopulse.co.kr
5.1.2. Usage of RDB
Install RDB: Modules
Install power in RDB: Battery or USB
Battery power
Check 1.
* Jumper setting
Check 2.
* Power switch
locate to BAT_ON

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:10/31
www.radiopulse.co.kr
USB power
Enter the paring mode
** Pairing mode will remain 30 seconds.
Check 1.
* Jumper setting
Check 2.
* Power switch
locate to USB_ON
Step 3.
* Press button
“1”to request pair.
Step 1.
* Press buttons “*”and “#”
together.(about 3Sec)
Step 2.
* When start the LED toggle,
release the buttons.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:11/31
www.radiopulse.co.kr
Operating: KEY
Open the “Notepad”and Press the buttons.
Operating: MOUSE
Move like the air mouse.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:12/31
www.radiopulse.co.kr
Operating: VOICE
Enter the “Voice”mode.
Use the “Voice”
Step 3.
* Press button “7”
to request voice.
Step 1.
* Press buttons “*”and “#”
together.(about 3Sec)
Step 2.
* When start the LED toggle,
release the buttons.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:13/31
www.radiopulse.co.kr
PC setting.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:14/31
www.radiopulse.co.kr
Exit the “Voice”mode.
Un-pair
Step 3.
* Press button
“8”to exit voice.
Step 1.
* Press buttons “*”and “#”
together.(about 3Sec)
Step 2.
* When start the LED toggle,
release the buttons.
Step 3.
* Press button
“2”to un-pair.
Step 1.
* Press buttons “*”and “#”
together.(about 3Sec)
Step 2.
* When start the LED toggle,
release the buttons.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:15/31
www.radiopulse.co.kr
5.2. MG2470-EVB(Target) to RDB(Controller) : Operating with RC-
Simulator
Each firmware file is like below;
- MG2470-EVB : MG2475_RdkTarget_SIM.hex
in [Package CD\0. Getting Started Manual\Firmware\]
- RDB : MG2475_RdkController.hex
in [Package CD\0. Getting Started Manual\Firmware\]
5.2.1. Usage of Remote Controller-Simulator
- Install RCS Setup Vx.xx.exe file to PC
in [Package CD\3. Development Tool and Drivers\RadioPulse Remote-Controller
Simulator\Remote Controller-Simulator 1.10\](see also [R1])
(A) Connection button.
a) Port : Target’s COM port
b) Rates : 460,800

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:16/31
www.radiopulse.co.kr
(B) Touch Pad pointer position
(C) Pair status indicator.
(D) Handle the received voice data
(E) Mouse position information window.
(F) Pair Request button.
(G) Cold-Reset button.
Install MG2470-EVB+LM2475-EM

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:17/31
www.radiopulse.co.kr
Pairing
Pairing Success
When the pairing is completed, the pair status image of Remote-controller simulator is
changed as below;
* Click “Start Pairing”button

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:18/31
www.radiopulse.co.kr
5.2.2. Usage of RDB
Install RDB: Modules
Install power in RDB: Battery or USB
Battery power
Check 1.
* Insert to J3
Check 1.
* Jumper setting
Check 2.
* Power switch
locate to BAT_ON

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:19/31
www.radiopulse.co.kr
USB power
Enter the paring mode
** Pairing mode will remain 30 seconds.
Check 1.
* Jumper setting
Check 2.
* Power switch
locate to USB_ON
Step 3.
* Press button
“1”to request pair.
Step 1.
* Press buttons “*”and “#”
together.(about 3Sec)
Step 2.
* When start the LED toggle,
release the buttons.

ASW1008 [MG2475-RDK] Getting Started
V0.96 Page:20/31
www.radiopulse.co.kr
5.3. MG2475-Dongle(Target) to RCU(Controller)
MG2475-Dongle and RCU firmware are already downloaded.
Each firmware file is like below;
- MG2475-Dongle : MG2475_RdkTarget_DONGLE.hex
in [Package CD\0. Getting Started Manual\Firmware\]
- RCU : Firmware is not provided.
5.3.1. Usage of MG2475-Dongle
Install MG2475-Dongle
Enter the pairing mode
** Pairing mode will remain 30 seconds.
* Status LED
On: Already Paired
Off: Un-pair
Toggle: Pairing mode
* Pairing Button