Radio Shack Trunk Mount User manual

Cat. No. 12-1976
OWNER’S MANUAL
Please read before using this equipment.
4 ×25 Watt
Trunk Mount Amplifier
4-Channel 100-Watt
12-1976.fm Page 1 Tuesday, July 13, 1999 10:01 AM

2
FEATURES
© 1995 Tandy Corporation.
All Rights Reserved.
Optimus and Radio Shack are registered trademarks used by Tandy Corporation.
Your Optimus 4 ×25 Watt Trunk
Mount Amplifier is designed to pro-
duce a total of 100 watts to give add-
ed punch and power to your vehicle’s
existing stereo system.
The amplifier produces up to 25
watts per channel of clean, powerful
sound at all audio frequencies with
minimum distortion. And, you can
connect line-level as well as speaker
outputs to the amplifier.
Its features include:
14k Gold-Plated Noise-Isolated
Line-Level Input Jacks -let you
connect low-level (pre-amplifier) sig-
nal inputs to match your autosound
system’s output for the best high-fi-
delity performance.
14k Gold-Plated Speaker Termi-
nals -designed for low impedance,
high conductivity, and minimum cor-
rosion to provide the highest signal
transfer and lowest sound distortion.
Input Level Control - letsyou adjust
the level (high or low) of the audio
signals that enter the amplifier.
Automatic Power Switchin
g
-auto-
matically turns on/off the amplifier
when you turn on/off your autosound
system.
Short Circuit Protection -distorts
sound if any output channel shorts to
protect the amplifier from damage.
Power Indicator -lights when power
is on.
Note: If the connectors from your au-
tosound system are not compatible
with the amplifier’s connectors, your
local Radio Shack store sells adapter
harnesses for many vehicles.
12-1976.fm Page 2 Tuesday, July 13, 1999 10:01 AM

3
CONTENTS
Preparation ..................................................................................................... 4
Choosing a Mounting Location .................................................................. 4
Before You Begin the Installation ............................................................... 4
Connecting Ground and Primary/Switched Power .................................... 5
Connecting Your Autosound System ......................................................... 7
Low Level Input Connections .............................................................. 7
High-level Input Connections ............................................................ 10
Connecting the Speakers ........................................................................ 13
Preparing the Speaker Wires ............................................................ 13
Connecting Four Speakers ................................................................ 14
Connecting Two Speakers ................................................................ 15
Testing the Connections .......................................................................... 16
Mounting the Amplifier ............................................................................. 16
Operation ...................................................................................................... 18
Turning On the Amplifier .......................................................................... 18
Setting the Level Control ......................................................................... 18
Maintenance .................................................................................................. 20
Replacing the Fuses ................................................................................ 21
Replacing the Tube-Type Fuse ......................................................... 21
Replacing the Blade-Type Fuse ........................................................ 21
Specifications ............................................................................................... 22
12-1976.fm Page 3 Tuesday, July 13, 1999 10:01 AM

4
PREPARATION
CHOOSING A MOUNTING LOCATION
The ideal location for mounting the amplifier is in your vehicle’s trunk. Wherever
you decide to mount it, choose a mounting location that:
• Does not interfere with the vehicle’s operation
• Lets you drill mounting holes without damaging other vehicle components
• Allows enough space around the cooling fins for proper airflow and cooling
Warnin
g
: The amplifier gets very hot while it is on. Do not touch the amplifier or
place flammable objects near it while it is on.
BEFORE YOU BEGIN THE INSTALLATION
Before you install your amplifier, carefully read all the instructions in this owner’s
manual. You should be able to answer all ofthese questions about your vehicle’s
electrical and sound systems.
• Does my vehicle have a 12-volt negative ground system? (If it does not, you
cannot use this amplifier.)
• Which of the amplifier’s wires is the power wire?
• How do I connect a wire to the fuse box?
• Which amplifier terminals are line-level inputs, which are speaker-level
inputs, and which are speaker outputs?
Important!
• Be aware that installation in your vehicle may require cutting or modifying
your vehicle.
• Do not cut any of the amplifier’s wires. If you cut any wire, you cannot obtain
a refund or exchange on this product. Radio Shack will provide warranty
service if you cut a wire and find the product is defective.
12-1976.fm Page 4 Tuesday, July 13, 1999 10:01 AM

5
Cautions:
• To prevent damage to your amplifier or autosound system, you must first
connect the ground, primary, and switched power wires (as described in
“Connecting Ground and Primary/Switched Power” before you connect the
speakers to the amplifier. Make the connections only in the order shown.
Damage to the amplifier is possible if you connect any wire incorrectly.
• Turn on the power to test the connections before you permanently mount
the amplifier (see “Testing the Power Connections”).
• Be sure your speakers can handle 25 watts per channel if you connect the
autosound system to two pairs of speakers (or 50 watts per channel if you
connect the autosound system to only one pair of speakers). Each speaker
must have an impedance of at least 4 ohms. Your local Radio Shack store
carries a full line of speakers to choose from.
CONNECTING GROUND AND PRIMARY/SWITCHED
POWER
1. To prevent damage to your amplifier or autosound system while making the
connections, disconnect the negative (-) cable from your vehicle’s battery.
12-1976.fm Page 5 Tuesday, July 13, 1999 10:01 AM

6
Note: After you complete the connections and reconnect the battery wire,
you will need to reset all clock/timer/memory devices in your vehicle.
2. Connect the supplied dark blue/white wire’s end to the amplifier’s REM
(remote power) terminal.
3. Securely connect the supplied dark blue/white wire’s male quick disconnect
plug to your autosound system’s switched power lead.
This connection turns your amplifier on or off when you turn your autosound
system on or off.
Note: If your autosound system does not have a remote power output lead,
connect this wire to a point in your vehicle’s ignition switch that provides 12-
volt battery power when the ignition is set to ON or ACC. This connection
turns on the amplifier when you turn your ignition switch to on (or to ACC)
and turns off the amplifier when you turn off the ignition.
4. Connect the black wire’s spade connector to the amplifier’s GND terminal.
5. Securely connect the black wire’s eyelet-terminal to a nearby metal ground,
such as a bolt attached to a part of the vehicle’s chassis.
Note: Be sure the bolt is not insulated from the chassis by a plastic part or
other insulating material.
6. Connect the red wire’s spade connector to the amplifier’s +12V terminal.
7. Remove the nut from the battery’s positive (+) terminal bolt, then place the
red wire’s 10A fused eyelet terminal over the end of the bolt.
Caution: Due to the amplifier’s high current requirement, you MUST con-
nect the red wire’s fused end directly to the vehicle’s positive (+) battery
cable terminal or damage to your vehicle’s wiring could result.
Note: Do not reconnect your vehicle battery’s negative (-) cable yet.
12-1976.fm Page 6 Tuesday, July 13, 1999 10:01 AM

7
CONNECTING YOUR AUTOSOUND SYSTEM
Low Level Input Connections
You can connect your autosound system’s low-level phono output jacks to the
amplifier’s LOW INPUT phono jacks.
Note: For a cleaner, less noisy signal transfer between your autosound system
and the amplifier, the amplifier’s LOW INPUT phono jacks are gold-plated.
For the best results, use shielded audio cables, such as Cat. No. 42-2368 (not
supplied). If your autosound system has only two phono outputs, you will also
need two shielded Y-adapter cables, such as Cat. No. 42-2435 (not supplied).
1. Temporarily place the amplifier as close as possible to the selected mount-
ing location.
2.
If your autosound system has four phono outputs and you are using four
speakers
, connect the autosound system to the amplifier using audio cables
as follows: front-left to FRONT L, front-right to FRONT R, rear-left to REAR L,
and rear-right to REAR R:
12-1976.fm Page 7 Tuesday, July 13, 1999 10:01 AM

8
If your autosound system has four phono outputs but you are using only two
speakers (front or rear)
, connect only the corresponding autosound sys-
tem’s output jacks to the amplifier using audio cables as follows:
• front-left to FRONT L and front-right to FRONT R, or
• rear-left to REAR L and rear-right to REAR R
12-1976.fm Page 8 Tuesday, July 13, 1999 10:01 AM

9
If your autosound system has only two phono output jacks (left and right)
and you are using four speakers,
first connect the single phono plug end of
a Y-adapter shielded audio cable to each autosound system output jack.
Then:
• Connect the other two ends of the left Y-adapter to the amplifier’s corre-
sponding FRONT L and REAR L phono jacks
• Connect the other two ends of the right Y-adapter to the amplifier’s corre-
sponding FRONT R and REAR R phono jacks
12-1976.fm Page 9 Tuesday, July 13, 1999 10:01 AM

10
If your autosound system has only two phono output jacks (left and right)
and you are using only two speakers,
simply connect them to the amplifier’s
corresponding FRONT L and FRONT R, or REAR L and REAR R phono jacks.
High-Level Input Connections
Ifyour stereo system has onlyspeaker outputs, you can connectthem to the am-
plifier’s rear HIGH INPUT and front HIGH INPUT sockets using the floating ground
connection or the common ground connection method.
12-1976.fm Page 10 Tuesday, July 13, 1999 10:01 AM

11
If your autosound system has four speaker outputs and you are going to use four
speakers:
Floating
Ground
Connection
Common
Ground
Connection
12-1976.fm Page 11 Tuesday, July 13, 1999 10:01 AM

12
If your autosound system has only two speaker outputs and you are going to use
four speakers:
Floating
Ground
Connection
Common
Ground
Connection
12-1976.fm Page 12 Tuesday, July 13, 1999 10:01 AM

13
CONNECTING THE SPEAKERS
With the speakers placed in their approximate locations, run one speaker wire
from each speaker to the amplifier. We recommend you use 16- or 18-gauge
marked or color-coded wires to help you correctly connect the speakers to your
amplifier. For the maximum bass response and the best overall performance,
keep your speakers properly phased (connect + to + and -to -).
Caution: Do not connect the speakers’ negative (-) terminal wires to chassis
ground.
Note: Speaker wires have two conductors. Color-coded wires have a stripe run-
ning down one of the conductors or different colored insulation for each conduc-
tor. Your local Radio Shack store has a wide selection of speaker wire to choose
from.
Preparing the Speaker Wires
1. Separate each speaker wire’s two conductors at both ends for a length of
about 4 inches.
2. Strip the insulation from the ends of each conductor to expose 1/4inch of
wire.
Note: Be sure to twist the ends to secure loose strands.
12-1976.fm Page 13 Tuesday, July 13, 1999 10:01 AM

14
Connecting Four Speakers
1. Connect one end of a speaker wire’s marked conductor to the amplifier’s
FL+(front-left positive) terminal.
2. Connect one end of the speaker wire’s unmarked conductor to the ampli-
fier’s FL-(front-left negative) terminal.
3. Repeat Steps 1 and 2 to connect a speaker wire to the amplifier’s FR (front-
right) terminals.
4. Repeat Steps 1 -3 to connect speaker wires to the amplifier’s RL (rear-left)
and RR (rear-right) terminals.
5. Connect the other ends of the four speaker wires so FL connects to the
front-left speaker, FR to the front-right speaker, RL to the rear-left speaker,
and RR to the rear-right speaker.
12-1976.fm Page 14 Tuesday, July 13, 1999 10:01 AM

15
Connecting Two Speakers
If you are connecting only two speakers, you can connect them to the amplifier’s
front (FL and FR) or rear (RL and RR) speaker terminals.
1. Connect one end of a speaker wire’s marked conductor to the amplifier’s
FL+(front-left positive) or RL +(rear-left positive) terminal.
2. Connect the end of the speaker wire’s unmarked conductor to the ampli-
fier’s FL−(front-left negative) or RL −(rear-left negative) terminal.
3. Repeat Steps 1 and 2 to connect a speaker wire to the amplifier’s FR+and
FR−(front-right) or RR +or RR −(rear-right) terminals.
4. Connect the other ends of the speaker wires so FL connects to the front-left
speaker and FR to the front-right speaker, or RL connects to the rear-left
speaker and RR connects to the rear-right speaker.
12-1976.fm Page 15 Tuesday, July 13, 1999 10:01 AM

16
TESTING THE CONNECTIONS
Before you permanently mount the amplifier, temporarily reconnect your vehicle
battery’s negative (-) cable, turn your vehicle’s ignition to ON or ACC, then test
the connections.
The amplifier is properly connected to the autosound system and speakers if you
can verify that the amplifier and the autosound system turn on properly and the
speakers’ sound is clear and unmuffled.
If you cannot quickly verify that all components operate properly,
immediately
turn off your vehicle’s ignition
. Then disconnect your vehicle battery’s nega-
tive (-) cable and recheck your connections.
If you verify that all components operate properly, mark the connections to insure
easy identification of each wire, then follow the instructions under “Mounting the
Amplifier.”
MOUNTING THE AMPLIFIER
Before you begin mounting the amplifier, make sure you have the following sup-
plied hardware necessary for mounting.
• 4 sheet-metal screws
• 4 spring washers
• 4 flat washers
Then confirm that the amplifier fits your vehicle’s mounting area.
Caution: Be careful to not drill into anything behind the mounting surface
1. Temporarily disconnect your vehicle battery’s negative (-) cable again.
2. To make mounting more convenient, temporarily disconnect the amplifier’s
wiring (ground, primary power, remote power, your autosound system’s
input, and speakers).
12-1976.fm Page 16 Tuesday, July 13, 1999 10:01 AM

17
3. Using the mounting holes on the amplifier as a guide, mark the locations for
the mounting holes.
4. Drill 9/64-inch holes in the marked locations, being careful not to damage
anything behind the mounting surface.
5. Attach the amplifier to the mounting surface using the supplied sheet-metal
screws and washers.
6. Reconnect the wiring.
7. Reconnect your vehicle battery’s negative (-) cable.
12-1976.fm Page 17 Tuesday, July 13, 1999 10:01 AM

18
OPERATION
TURNING ON THE AMPLIFIER
The amplifier automatically turns on whenever you turn on your autosound sys-
tem. POWER lights when the amplifier is operating.
SETTING THE LEVEL CONTROL
For the best performance, you can adjust the level of the audio signals that enter
the amplifier by following these steps.
Cautions:
• The sound distorts if any output channel shorts. Turn off the amplifier and
try to locate the short.
• To prevent draining the vehicle’s battery, do not play the amplifier for too
long using the ignition switch’s ACC position after turning off the vehicle’s
ignition.
1. Using a flat blade screwdriver, turn both LEVEL MIN/MAX controls fully coun-
terclockwise to MIN.
Note: The right level control is for the front speakers; the left level control is
for the rear speakers.
12-1976.fm Page 18 Tuesday, July 13, 1999 10:01 AM

19
2. Temporarily turn up the autosound system’s volume control to about one-
third of its full range.
Caution: Never turn the level controls up any farther than you need to get
clear sound at two thirds volume maximum.
3. Turn either the left or right LEVEL control clockwise until you can hear the
sound at a comfortable level.
4. Turn up the volume on your autosound system until the sound begins to dis-
tort. Then immediately turn down the volume to the point just below where
distortion began.
5. Adjust the level controls until the volume is at the maximum level you want
the autosound system to produce.
6. Adjust the autosound system’s volume control to a comfortable listening
level.
12-1976.fm Page 19 Tuesday, July 13, 1999 10:01 AM

20
MAINTENANCE
CLEANER
Keep the amplifier dry. If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode electronic circuits.
Use and store the amplifier only in normal temperature envi-
ronments. Temperature extremes can shorten the life of elec-
tronic devices and distort or melt plastic parts.
Handle the amplifier gently and carefully. Dropping it can
damage circuit boards and cases and cause the amplifier to
work improperly.
Keep the amplifier away from dust and dirt, which can cause
premature wear of parts.
Wipe the amplifier with a damp cloth occasionally to keep it
looking new. Do not use harsh chemicals, cleaning solvents,
or strong detergents to clean the amplifier.
Your Optimus 4 ×25 Watt Trunk Mount Amplifier is an example of superior
design and craftsmanship. The following suggestions will help you care for
your amplifier so you can enjoy it for years.
Modifying or tampering with the amplifier’s internal components can cause a
malfunction and invalidate your amplifier’s warranty. If your amplifier is not per-
forming as it should, take it to your local Radio Shack store for assistance.
12-1976.fm Page 20 Tuesday, July 13, 1999 10:01 AM