Radiodetection RD8000 User manual

RD8000™
Universal precision electromagnetic
and RF marker locator
User Guide
Kurzbedienungsanleitung
90/UG096INT/02

ENGLISH 4
DEUTSCH 32

ENGLISH
4 5
Preface
About this guide
CAUTION: This guide provides basic operating instructions for the RD8000
locator and transmitter. It also contains important safety information and
guidelines and as such should be read in its entirety before attempting to
operate the RD8000 Locator and transmitter.
This guide is intended as a quick reference guide only. For detailed instructions,
including the use of accessories, help with eCert™, CALSafe™*, SurveyCERT™and
automatic logging* please refer to the RD8000 locator operation, SurveyCERT and
RD Manager™manuals, which are available for download from www.radiodetection.com.
The online User Manual library also contains links to the SurveyCERT and
RD Manager manuals.
*Logging and GPS models only.
WARNING! Direct connection to live conductors is POTENTIALLY LETHAL.
Direct connections to live conductors should be attempted by fully qualified
personnel only using the relevant products that allow connections to energized
lines.
WARNING! The transmitter is capable of outputting potentially lethal
voltages. Take care when applying signals to any pipe or cable and be sure to
notify other technicians who may be working on the line.
WARNING! Reduce audio level before using headphones to avoid damaging
your hearing.
WARNING! This equipment is NOT approved for use in areas where
hazardous gases may be present.
WARNING! When using the transmitter, switch off the unit and disconnect
cables before removing the battery pack.
WARNING! The RD8000 locator will detect most buried conductors but
there are some objects that do not radiate any detectable signal. The RD8000,
or any other electromagnetic locator, cannot detect these objects so proceed
with caution. There are also some live cables which the RD8000 will not be able
to detect in Power mode. The RD8000 does not indicate whether a signal is
from a single cable or from several in close proximity.
WARNING! Batteries can get hot after prolonged use at full output power.
Take care while replacing or handling batteries.
Extended Warranty
Thank you for purchasing the RD8000 locator and transmitter.
RD8000 locators and transmitters are covered by a 1 year warranty as standard.
Customers can extend this warranty to a total of 3 years by registering the
products within 3 months of purchase.
Registration is carried out using the RD Manager PC software which can be
downloaded from the Radiodetection website. Visit www.radiodetection.com/
RDManager.
From time to time Radiodetection may release new software to improve the
performance or add new functionalities to these products. By registering, users
will benefit from subscribing to email alerts advising about any new software and
special offers related to its product range.
Users will be able to opt out at any moment from receiving software or technical
notifications as well as from receiving marketing material.
eCert
The RD8000 locator is safety equipment which should be regularly checked to
ensure its correct operation.
eCert provides a thorough test of the RD8000’s locating circuitry and marker
transceiver, and supplies a Radiodetection Calibration Certificate when a positive
test result is obtained.
To run eCert, the locator should be connected to an internet-enabled PC
on which the RD Manager software is installed. Additional purchase may be
required.
Refer to the RD Manager operation manual for further details.

ENGLISH
6 7
RD8000 locator
1
2
5
6
7
9
3
4
8
16 17 181822
10
11
12 13 14
1512
32
35
36
37
38
34
19
20
21
23
24
25 26 27 29 3033 3128
12 or more satellites in view
9-11 satellites in view
6-8 satellites in view
3-5 satellites in view
GPS satellite lock acquired
GPS active, seeking satellite lock
Locator features
1. Keypad
2. LCD with auto backlight
3. Speaker
4. Battery compartment
5. Battery charger connector
6. Accessory connector
7. Headphone connector
8. Bluetooth module antenna
9. Marker loop antenna
Locator keypad
10. Power key : Switches the unit on
and off. Opens the locator menu.
11. Frequency key : Selects frequency.
Closes submenu.
12. Up and down arrows : Adjusts
the signal gain. Scrolls through the
menu options.
13. Antenna key : With antenna folded
up, toggles peak, combined peak/
null, null, single antenna and guidance
modes. With antenna folded down,
toggles marker and combined (marker/
line) modes. Opens a submenu.
14. Graph key : Saves SurveyCERT
measurements.
15. Transmitter key : Sends iLOC™
commands on iLOC enabled locators
to iLOC enabled transmitters.
Locator screen icons
16. Indicates the signal strength and peak
marker.
17. Signal strength: Numerical indication
of signal strength.
18. Peak / Proportional arrows: Indicates
the location of the line relative to the
locator.
19. Battery icon: Indicates the battery level.
20. Sensitivity and Log number: Displays
the log number momentarily after a
survey log is saved to memory.
21. Volume icon: Displays the volume level.
22. Current Direction arrows.
23. Radio Mode: Indicates when Radio
Mode is active.
24. Power Mode: Indicates when Power
Mode is active.
25. Accessory or Measurement indicators:
Indicate when an accessory is connected
or if measurements are active.
26. CD Mode icon: Indicates when Current
Direction Mode is active.
27. A-Frame icon: Indicates when the
A-Frame is connected.
28. Operating mode indicator.
29. Bluetooth icon: Indicates status of
Bluetooth connection. Flashing icon
means pairing is in progress. Solid icon
indicates an established connection is
active.
30. Antenna mode icon: Indicates antenna
selection: Peak, Null, Single and
combined Peak/Null.
31. Sonde icon: Indicates that the signal
source is from a sonde.
32. Line icon: Indicates that the signal
source is from a line.
33. Compass/ Marker mode indicator: Shows
the direction of the located cable relative
to the locator. Also used as a graphical
indication for Marker mode active.
34. Tx status: Displays transmitter
connection status.
35. Tx standby: Indicates that the
transmitter is in Standby Mode.
36. Current /depth indicator.
37. GPS Status icon: One bar indicates
that GPS is active. 3 bars indicates
that the GPS has locked to the GPS
satellite system – GPS models only.
38. GPS Signal quality icon: Indicates
the quality of the signal being received
– GPS models only.

ENGLISH
8 9
Tx-1, Tx-5 and Tx-10 transmitters
1
3
2
10
11
12 13 14
15
16
17
18
19
20
21
22
5
4
6
7
8
9
Transmitter features
1. Keypad.
2. LCD.
3. Removable accessory tray.
4. D-cell battery tray.
5. Rechargeable battery pack
(Optional).
Transmitter keypad
6. Power key : Switches the unit on
and off. Opens the transmitter menu.
7. Frequency key : Selects frequency.
Menu navigation key.
8. Up and down arrows : Adjusts
the output signal. Scrolls through the
menu options.
9. Measure key : Opens a sub menu.
Used to take voltage and impedance
measurements.
Transmitter screen icons
10. Battery icon: Indicates the battery level.
11. Alphanumeric description of selected
operation mode.
12. Standby icon: Appears when the
transmitter is in Standby Mode.
13. Output level: Displays transmitter
output power.
14. Clamp icon: Indicates when a clamp or
other plug is connected.
15. DC icon: Appears when the transmitter
is powered from a DC source.
16. Induction indicator: Appears when the
transmitter is in Induction Mode.
17. A-Frame (Tx-5 and Tx-10 only):
Indicates when the transmitter is in
Fault-Find Mode.
18. CD Mode indicator (Tx-10 only):
Indicates that the transmitter is in
Current Direction Mode.
19. Voltage warning indicator: Indicates
that the transmitter is outputting
potentially hazardous voltage levels.
20. Volume icon: Displays the
volume level.
21. Pairing icon (Tx-5B and Tx-10B only):
Appears when the transmitter and
locator are connected via iLOC.
22. Bluetooth icon (Tx-5B and Tx-10B
only). Indicates status of Bluetooth
connection Flashing icon means pairing
is in progress.

ENGLISH
10 11
Before you begin
IMPORTANT! This guide is intended to be a quick reference guide. We recommend
you read the operation manual before you attempt to operate the RD8000 locator!
First use
For safety reasons RD8000 locators are shipped with the Li-Ion battery packs
disconnected and transmitters with no D cells in the battery tray.
To connect the Li-Ion battery pack open the RD8000 battery compartment and plug the
battery lead into the battery connector.
To fit the D cell batteries in the transmitter, unlatch the accessory tray. The battery
compartment is located underneath the transmitter body. Use the turnkey to unlatch
the battery compartment. Insert eight D-Cell Alkaline or NiMH batteries.
System setup
It is important that you set up the system according to your personal preferences and
operating requirements before you conduct your first survey. You can set the system up
using the RD8000 menu as described below.
NOTE: These procedures refer to both the transmitter and locator unless stated
otherwise.
Before changing settings, switch the locator or transmitter on by pressing the key.
NOTE: Once the system is switched on, pressing the key momentarily will
activate the locator or transmitter menu.
Using the menus
The RD8000 locator and transmitter menus allow you to select or change system options.
Once entered, the menu is navigated using the arrow keys. Navigation is consistent on both
the transmitter and the locator. When in the menu, most on-screen icons will temporarily
disappear and the menu options will appear in the bottom left-hand corner of the display.
Note that when browsing the locator menu, the and keys act as left and right arrows.
When browsing the transmitter menu the and keys act as left and right arrows. The
right arrow enters a submenu and the left arrow returns to the previous menu.
NOTE: When you select an option and press the key, the option will be enabled
automatically.
Locator menu options
• VOL: Adjust the speaker volume from 0 (mute) to 3 (loudest).
• LOG or DATA: Delete, send or review saved SurveyCERT measurements and enable
or disable the communication channel.
• BT: Enable, disable, reset or pair Bluetooth connections. Also defines the protocol
used when connecting to a PC or PDA.
• GPS: Select an external GPS module or enable or disable the internal GPS module
(GPS models only).
• CDR: CD Reset. Only available when in CD mode.
• UNITS: Select metric or imperial units.
• CAL: Displays the date of original factory calibration and the most recent service
calibration or eCert calibration validation.
• MARKR: Enable or disable individual utility markers.
• LANG: Select menus language.
• POWER: Select power frequency: 50 or 60Hz.
• ANT: Enable or disable any antenna mode with the exception of Peak.
• FREQ: Enable or disable individual frequencies.
• ALERT: Enable or disable StrikeAlert™.
• BATT: Set battery type: ALK, NiMH or Li-ION.
• COMP: Enable or disable display of the Compass feature.
To navigate the locator menu:
1. Press the key to enter the menu.
2. Use the or keys to scroll through the menu options.
3. Press the key to enter the option’s submenu.
4. Use the or keys to scroll through the submenu options.
5. Press the key to confirm a selection and return to the previous menu.
6. Press the key to return to the main operation screen.
Transmitter menu options
• VOL: Adjust the speaker volume from 0 (mute) to 3 (loudest).
• FREQ: Enable or disable individual frequencies.
• BOOST: Boost transmitter output for a specified period of time (in minutes).
• LANG: Select menus language.
• OPT F: Enable or disable SideStepauto™(Bluetooth models only).
• BATT: Set battery type: ALK, NiMH or Li-ION – Also select Eco mode for alkaline
batteries only.
• MAX P: Allow the transmitter to output its maximum wattage.
• MODEL: Specify the model of your locator.
• MAX V: Set the output voltage.
• BT: Enable, disable or pair Bluetooth connections (Bluetooth models only).

ENGLISH
12 13
To navigate the transmitter menu:
1. Press the key to enter the menu.
2. Use the or keys to scroll through the menu options.
3. Press the key to enter the option’s submenu.
4. Use the or keys to scroll through the submenu options.
5. Press the key to return to the previous level or exit the menu.
6. Press the key to return to the main operation screen.
Examples of using the menu, selecting options
and making changes:
Language
To select your preferred menu language:
1. Press the key to enter the menu.
2. Scroll to the LANG menu using the or keys.
3. Press the key (on the locator) or the key (on the transmitter) to enter the LANG menu.
4. Scroll up or down to select your preferred language.
5. Press the key to accept your selection and return to the main menu.
6. Press the key to return to the main operation screen.
Power / mains frequency (locator only)
To select the correct frequency (50 or 60Hz) for your country or region’s power supply:
1. Press the key to enter the menu.
2. Scroll to the POWER menu using the or keys.
3. Press the key to enter the POWER menu.
4. Scroll up or down to select the correct frequency.
5. Press the key to accept your selection and return to the main menu.
6. Press the key to return to the main operation screen.
Units (locator only)
The RD8000 locator allows you to work in Metric or Imperial (US customary) units.
To select your preferred units of measurements:
1. Press the key to enter the menu.
2. Scroll to the UNIT option using the or keys.
3. Press the key to enter the UNIT submenu.
4. Scroll up or down to select Metric or Imperial units.
5. Press the key to accept your selection and return to the main menu.
6. Press the key to return to the main operation screen.
Batteries
The locator and transmitter are battery powered.
The RD8000 locators are provided with a rechargeable Lithium-ion (Li-Ion) battery
pack as standard. The RD8000 locators can also be powered using good quality D-cell
alkaline or NiMH batteries.
Transmitters can be powered by D-cell alkaline batteries (as standard), D-cell NiMH
batteries, or by an optional accessory Li-Ion battery pack. Alternatively, you can power
the transmitter from a mains or vehicle power source using a Radiodetection supplied
optional accessory adapter.
If using D-Cells it is important to set the system to match the currently installed battery
type to ensure optimal performance and correct battery level indication.
To set your battery type:
1. Press the key to enter the menu.
2. Scroll to the BATT menu using the or arrows.
3. Press the key (on the locator) or the key (on the transmitter) to enter the
BATT menu.
4. Scroll up or down to select the correct battery type.
5. Press the key to accept your selection and return to the main menu.
6. Press the key to return to the main operation screen.
When using alkaline batteries Eco mode can be selected to maximize their usage. When
Eco mode is selected the transmitter automatically reduces its max power output when
the batteries cannot longer supply enough energy.
Shutting down
To switch the locator or the transmitter off, press and hold the key until the screen
goes blank.
Locating pipes and cables
Passive Frequencies
Passive frequency detection takes advantage of signals that are already present on buried
metallic conductors. The RD8000 supports four types of passive frequencies: power,
radio, CPS* and Cable TV (CATV)* signals. You can detect these frequencies without the
aid of the transmitter.
*Model specific.

ENGLISH
14 15
Active Frequencies
Active frequencies are applied direct to the pipe or cable using the transmitter. The
transmitter can apply a signal using three different methods:
Direct connection
In direct connection, you connect the transmitter directly to the pipe or cable you wish to
survey. The transmitter will then apply a discrete signal to the line, which you can trace
using the locator. This method provides the best signal on an individual line and enables
the use of lower frequencies, which can be traced for longer distances.
Connecting the transmitter to a pipe or line requires the use of a direct connection lead
and a ground stake to complete the circuit.
WARNING! Direct connection to live conductors is POTENTIALLY LETHAL. Direct
connections to live conductors should be attempted by fully qualified personnel only
using the relevant products that allow connections to energized lines.
Induction
The transmitter is placed on the ground over or near the survey area. You select the
appropriate frequency. The transmitter will then induce the signal indiscriminately to
any nearby metallic conductor. In induction mode, using higher frequencies is generally
recommended as they are induced more easily onto nearby conductors.
Clamp
The optional signal clamp can be used to apply the transmitter signal to an insulated live
wire or pipe up to 8.5"/215mm in diameter.
WARNING! Do not clamp around uninsulated live conductors.
WARNING! Before applying or removing the clamp around a power cable ensure
that the clamp is connected to the transmitter at all times.
Refer to the Signal Clamps paragraph in the Using Accessories section.
Locating RF Markers
The RD8000 locator enables users to locate most common RF utility markers. These are
also referred to as Electronic Marker System (EMS) and Omni markers.
To enable marker locate mode lower the marker loop antenna. To disable the marker
locate mode fold the loop antenna up.
Marker types
The RD8000 can detect 9 different RF Markers, as shown in the table below.
UTILITY COLOR DISPLAY FREQUENCY
ABBREVIATION
French Power Natural PFR 40.0kHz
General / Non-drinkable water Purple PUR 66.35kHz
Cable TV Black/Orange CTV 77.0kHz
Gas Yellow GAS 83.0kHz
Telephone/Telecoms Orange TEL 101.4kHz
Sanitary Green SAN 121.6kHz
German Power Blue/Red PDE 134.0kHz
Water Blue H20 145.7kHz
Electrical Power* Red PWR 169.8kHz
*Use of the red Electrical Power (PWR) marker locate mode is subject to radio licensing restrictions
for Short Range Devices in the EU and possibly other countries. It is the responsibility of the user
to ensure that the red Power (PWR) marker locate mode is only enabled in countries where radio
licensing restrictions do not apply at the operating frequency of 169kHz.
If required and permitted use RD Manager to enable this frequency.
Using accessories
The locator and transmitter are compatible with a wide range of accessories. For detailed
information on using any of the accessories below please refer to the RD8000 locator
operation manual.
Signal clamps
When it is not possible to connect directly onto a pipe or cable, or induction mode is
unsuitable, a transmitter signal clamp may be used. The clamp is plugged into the output
of the transmitter and provides a means of applying a locate signal to an insulated live
wire. This is particularly useful with live insulated cables as it removes the need to disable
the power and break the line.
WARNING! Do not clamp around uninsulated live conductors.
WARNING! Before applying or removing the clamp around a power cable ensure
that the clamp is connected to the transmitter at all times.
To locate or identify individual lines a locator signal clamp can be connected to the
accessory socket of the locator and can be clamped around individual pipes or cables.

ENGLISH
16 17
Stethoscopes
At times, it may not be possible to use a clamp around a cable because of congestion
or inaccessibility. A stethoscope antenna should be used in place of a clamp to identify
cables.
Radiodetection supplies a range of stethoscopes to suit most applications.
To use a stethoscope, connect it to the locator’s accessory socket. The locator will
automatically detect the device and filter out location modes that are irrelevant.
Sondes and FlexiTrace
Sondes are battery powered transmitters that are useful for tracing non-metallic pipes.
The RD8000 can detect a range of sonde frequencies, including those transmitted by
Flexisondes, GatorCam™4 or flexiprobe™pushrod systems and P350 flexitrax™crawlers.
For a detailed guide on locating sondes, please refer to the operation manual.
A FlexiTrace is a traceable fiberglass rod incorporating wire conductors with a sonde
at the end. It is connected to the output of the transmitter and is typically used in small
diameter, non-metallic pipes. The user has the option of locating the entire length of the
cable or choosing to locate only the tip of the cable.
The FlexiTrace has a maximum power rating of 1W. When using the FlexiTrace with a
Radiodetection Tx-5(B) or Tx-10(B) transmitter the output limit must be set to 1W in the
MAX P menu and the output voltage limit set to LOW in the MAX V menu.
No settings are required for the Tx-1 transmitter.
WARNING: Failure to follow the Tx-5(B) or Tx-10(B) instructions above may
result in the tip of the FlexiTrace becoming too hot to touch, resulting in risk of
personal injury and damage to the equipment.
Fault-finding with an A-Frame
The RD8000 PDLM and PTLM models have the ability to detect cable sheath faults
accurately using an A-Frame accessory. The Tx-5(B) and Tx-10(B) provide a fault finding
signal that can be detected by the A-Frame as a result of the signal bleeding to ground
through damaged cable sheaths.
For a detailed guide to fault-finding, please refer to the operation manual.
Plug /Live cable connector
The plug connector is connected to the output of the transmitter and is used to put a signal
onto a line and trace it from a domestic mains plug to the service cable in the street.
The live cable connector can be used to apply a signal to a live cable. Only suitably
qualified personnel should use this equipment.
Current Direction (CD)
The Tx-10(B) transmitter is used to apply a unique CD signal onto a pipe or cable. This
signal can be used to identify an individual pipe or cable amongst a number of parallel
utilities. A CD signal clamp can be used to apply the unique signal to the pipe or cable and
a CD locator clamp or CD stethoscope can be used to identify individual pipes or cables.
Submersible Double Depth Antenna
This antenna is connected to the locator and used to locate pipes and cables underwater
at depths down to 100 metres.
WARNING: use of the submersible antenna should be by fully licensed and
experienced personnel only, and only after fully reading the operation manual!
Transmitter Rechargeable battery packs
Rechargeable battery packs for the transmitter are available and are supplied with suitable
chargers. The rechargeable battery packs provide superior performance over traditional
alkaline batteries.
Bluetooth wireless connections
RD8000 locators feature a Bluetooth wireless module, as standard, providing the ability
to connect to compatible devices such as transmitters (Tx-5B or Tx-10B only), PCs,
laptops or handheld devices running a compatible application.
NOTE: The RD8000 locator wireless features may be subject to national and or
local regulations. Please consult your local authorities for more information.
WARNING! Do not attempt any wireless connection in areas where such
technology is considered hazardous. This may include: petrochemical facilities,
medical facilities or around navigation equipment.
Switching Bluetooth on
By default RD8000 locators and Bluetooth enabled transmitters are shipped with the
Bluetooth wireless connection module disabled.
1. Press the key to enter the menu.
2. Scroll to the BT menu using the or keys.
3. Press the key (locator) or the key (transmitter) to enter the BT menu.
4. Scroll up or down to the ON option.
5. Press the key to switch Bluetooth ON and return to the previous menu.
Switching Bluetooth off
You can switch Bluetooth off to prolong battery life or comply with regulations in areas
where wireless communications are considered hazardous.
1. Press the key to enter the menu.
2. Scroll to the BT menu using the or keys.

ENGLISH
18 19
3. Press the key (locator) or the key (transmitter) to enter the BT menu.
4. Scroll up or down to the OFF option.
5. Press the key to switch Bluetooth off and return to the previous menu.
Pairing to a transmitter
To pair to a transmitter you require a Bluetooth enabled model such as the Tx-5B or Tx-10B.
Before you begin, you may choose to switch off all nearby Bluetooth equipment as they
may interfere with the locator and transmitter’s pairing process.
On the locator:
1. Press the key to enter the menu.
2. Scroll to the BT menu using the or keys.
3. Press the key to enter the BT menu.
4. Scroll to the PAIR menu and press the key to enter it.
5. Scroll to the BT-TX option.
NOTE: You must complete the pairing process within 90 seconds to prevent the
locator’s Bluetooth connection from timing out.
On the transmitter:
6. Press the key to enter the menu.
7. Scroll to the BT menu using the or keys.
8. Press the key to enter the BT menu.
9. Scroll to the PAIR option.
Starting the pairing process:
10. Press the key on the transmitter followed by the key on the locator. You must
press these keys within a 30 second window otherwise the connection may time out.
11. The transmitter and the locator will now attempt to pair.
When pairing is in progress, the transmitter and locator will display a flashing Bluetooth
icon. Pairing can take up to a minute. If the pairing process is successful, the transmitter
will display the icon and the locator will display a persistent Bluetooth icon for the
duration of the connection.
If pairing fails, ensure that any nearby Bluetooth devices are switched off or invisible then
repeat the process.
Once the locator and transmitter have successfully paired you can use iLOC to change
the transmitter’s output frequency and power levels remotely from the locator.
Pairing to a PDA or PC
Connection requirements:
• Any RD8000 locator.
• A compatible Bluetooth enabled PDA or Bluetooth enabled PC or Laptop.
NOTE: The procedure below describes the pairing process between a RD8000
locator and a PDA. Pairing to a PC follows the same steps for the RD8000 locator
and similar steps for your PC or laptop. Consult your PC or laptop Bluetooth pairing
instructions to pair with the RD8000 locator.
Pair the RD8000 locator to your PDA using your PDA’s Bluetooth software.
NOTE: The procedure for pairing your PDA may differ depending on the PDA make
and model. The following procedure should apply to most PDAs.
On the locator:
1. Press the key to enter the menu.
2. Scroll to the BT menu using the or keys.
3. Press the key to enter the BT menu.
4. Scroll up or down to the PAIR menu.
5. Press the key to enter the PAIR menu.
6. Scroll up or down to the BT-PC option.
7. Press the key and the locator will attempt to pair with your PDA.
On your PDA:
8. From the PDA’s Start menu, select Settings then select the Connections Tab
followed by the Bluetooth icon.
9. Ensure the Bluetooth radio is switched on and make the PDA visible to other devices.
10. Select the Devices tab and scan for new partnerships.
11. Create a partnership with the RD8M_xxx device.
12. If asked for a passkey, enter 1234.
13. Select the COM Ports tab and make a New Outgoing Port with the RD8000 locator.
Note the port number of the selected COM port.
Troubleshooting
Successful wireless communication depends on a number of factors including:
battery life, electromagnetic interference, device memory and physical obstructions.
Ensure that the RD8000 transmitter, locator and any other wireless device is sufficiently
charged for wireless communication. Note that many PDAs will suspend wireless
connections when their battery capacity drops below a threshold percentage. Consult
your device’s documentation for more information.

ENGLISH
20 21
Excessive electromagnetic interference can effectively limit the range of wireless
communication and / or corrupt data.
Your PDA device may have insufficient memory to maintain a wireless link, particularly if
the connection is sustained over an hour or longer. Make sure you quit applications on
your PDA using the method described in your device’s documentation.
Although iLOC can successfully function at distances up to 300m (1000ft) in direct line
of sight, your PDA (or notebook) and the RD8000 must be within 10m (30ft) to maintain
a wireless connection.
Resetting connections
If you experience problems with the RD8000 wireless Bluetooth technology features,
Radiodetection recommends resetting the connection and then pairing your device again:
1. Press the key to enter the menu.
2. Scroll to the BT menu using the or keys.
3. Press the key to enter the BT menu.
4. Scroll up or down to the RESET menu.
5. Press the key and the locator will purge all current connections.
6. Re-pair your devices.
Bluetooth error codes
If an error occurs when attempting to perform any Bluetooth command using the locator
to the transmitter or the locator to a PC or PDA, the LCD will display a code to help you
resolve the problem on the locator.
The codes are as follows:
BT CODE DESCRIPTION
BT001 Bluetooth not configured for this unit
BT002 Internal Bluetooth error
BT003 Locator not paired with transmitter
BT004 Locator not paired with PC/PDA
BT005 Paired but connection attempt failed. Power cycling may be required
BT006 Corrupt response received from transmitter
BT007 Indeterminate response received from transmitter
BT008 No response received from transmitter
TX?? Transmitter unable to change to the requested frequency
iLOC
iLOC is a standard feature of all RD8000 locator models. iLOC lets you control the
transmitter remotely using your RD8000 locator. With iLOC you can adjust the output
frequency, power settings and use SideStep. iLOC commands are sent over a Bluetooth
module that can operate at distances of up to 300m/1000ft in direct line of sight.
To use iLOC, the transmitter and locator must be paired.
NOTE: Operating in built up areas and in areas with high electromagnetic
interference may reduce iLOC’s performance.
Using iLOC
The locator and transmitter need to be switched ON and paired to use iLOC.
For optimum performance:
• Face the back end of the transmitter towards the locator as this is where the
Bluetooth module is fitted
• If possible, raise the transmitter off the ground by 30-60cm (1-2ft)
• Try to avoid obstructions in line of sight
NOTE: If any iLOC commands fail, move closer to the transmitter and repeat
the process.
Changing frequencies
Once the transmitter and the locator are paired, you can change the transmitter’s output
frequency remotely using the locator:
1. On the locator, select the frequency you want by pressing the key until the
frequency is displayed on screen.
2. iLOC commands are sent using the key, press it to send the new frequency to the
transmitter.
3. The locator’s LCD will display SEND momentarily and then OK if the transfer is
successful.
4. If the transfer is unsuccessful, the LCD will display an error code.
If the process fails, you may be out of range or there may be an error in the connection.
Move closer to the transmitter and retry the procedure. If the connection continues to fail,
return to the transmitter and reset the connection.
Adjusting power
iLOC lets you adjust the transmitter’s power output remotely; you can also put the
transmitter into standby mode and then wake it remotely.

ENGLISH
22 23
1. Transmitter power options are located in the TXOUT menu on the locator.
Press and hold the key to display the TXOUT menu.
2. Press the key to enter the TXOUT menu.
3. Scroll up or down through the power output options; these are:
• STDBY: Transmitter standby mode, the connection is still active but the output
is disabled.
• LOW: Low power output.
• MED: Medium power output.
• HIGH: High power output.
• BOOST: Temporarily boosts transmitter power output to its maximum level.
4. Once you have selected the mode you want, press the key to confirm.
5. Press and hold the key to select the new setting and exit the menu.
6. Press the key once to send the settings to the transmitter.
NOTE: When changing the transmitter frequency using iLOC, the chosen transmitter
power setting will be retained.
Sleep/wake the transmitter
To help you prolong battery life you can put the transmitter in standby mode (sleep), and
reactivate it again, using the locator.
To put the transmitter into standby mode, set the TXOUT menu on the locator to STDBY
using the “Changing transmitter power output” procedure described above.
This will disable the transmitter output.
To re-activate the transmitter output, select any power mode from LOW to BOOST using
the same procedure.
If the process fails, you may be out of range or there may be an error in the connection.
Move closer to the transmitter and retry the procedure. If the connection continues to fail,
return to the transmitter and reset the connection.
SideStep
SideStep allows you to change the output frequency on the transmitter. SideStep
changes the selected frequency by several Hertz and automatically sets the locator’s
locate frequency to match the transmitter’s output frequency.
1. On the locator, select the frequency you want by pressing the key until the
frequency is displayed on screen.
2. To step the frequency, press and hold the key until STEP appears on the LCD.
3. Press the key to send the SideStep command to the transmitter.
4. If the command is sent successfully, an asterisk (*) will appear on the locator next to
the frequency and STEP will appear on the transmitter below the frequency.
5. Repeat this process to disable SideStep.
Survey Measurements
RD8000 locator models are capable of recording up to 1000 survey measurements to
internal memory.
If the locator is a GPS model or if paired to Pocket PC (or PDA) with GPS, running a
compatible application such as SurveyCERT the locator will append positional information
alongside time and date to the data, providing spatial context.
NOTE: The internal GPS module needs to be switched on and connected to the
GPS satellite system.
Saving measurements
To save survey measurements, press the key.
To achieve accurate results the locator must be kept as still as possible during the saving
process.
The locator will always save measurements to internal memory. If Bluetooth is switched
on, paired to a device and BT-PC is enabled, , the locator will also attempt to send
the saved measurement to a paired PDA running SurveyCERT or to a PC running a
compatible application.
If your PC or PDA is out of reach, or if its Bluetooth features are disabled, the locator will
display an error code. To avoid these errors disable the Bluetooth survey measurements
transmission or ensure that your PC or PDA is within range and correctly paired.
NOTE: A flashing depth and/or current reading display means that the
measurement is poor and should be taken again. Poor readings may be caused by
nearby conductors or sources of electromagnetic interference.
Erasing measurements
The RD8000 locator allows you to delete all measurements. Erasing the log will wipe the
RD8000 memory and is usually recommended when you begin a new survey.
WARNING! Erasing measurements cannot be undone! Proceed with caution!
1. Press the key to enter to menu.
2. Press the or keys to select LOG menu.
3. Press the key to enter the LOG menu.
4. Scroll up or down to select the DEL option.
5. Press the key to make the selection and return to the main menu.
SurveyCERT
Stored data can be transferred wirelessly to a compatible PDA running Radiodetection’s
SurveyCERT app or a PDA or PC compatible application.

ENGLISH
24 25
The SurveyCERT PDA app can read and chart logged survey data for real-time or post
survey analysis. It can also export KML files for interface with GIS/mapping systems.
NOTE: SurveyCERT is only compatible with Bluetooth enabled PDAs running
Windows Mobile 6.5 as operating system.
Stored data can also be transferred using the USB connection to RD Manager to be
analyzed by the software’s built-in SurveyCERT capabilities. Refer to the RD Manager
operation manual for more info on how to retrieve store survey data.
RD Manager’s SurveyCERT functionality can be used for post survey analysis, interface to
Google Maps®and easy export to GIS/mapping systems.
NOTE: RD Manager is only compatible with PC running Microsoft Windows XP or higher.
To send stored data to your paired PDA:
1. Ensure your paired PDA is switched on and running the SurveyCERT app.
2. Press the key to enter the menu.
3. Scroll to the LOG menu using the or keys.
4. Press the key to enter the LOG menu.
5. Scroll up or down to the SEND option.
6. Press the key and the locator will attempt to send your stored survey data to your PDA.
To obtain SurveyCERT for PDA:
SurveyCERT for PDAs and its operation manual are available as a free download from the
Radiodetection website:
1. Visit www.radiodetection.com.
2. Using the menu bar, go to Support -> SurveyCERT.
3. Click on the RD8000 SurveyCERT link to get to the SurveyCERT download page
and follow the instructions.
To obtain RD Manager:
1. Go to www.radiodetection.com/RDManager.
2. Follow the instructions.
CALSafe
CALSafe enabled RD8000 locator models (logging and GPS only) are equipped with
a system which does not permit them to function once they are beyond the expected
service/calibration date.
When the unit is within 30 days of the service due date the unit will display at startup the
number of days left. The locator will stop functioning on the service due date.
You can edit the CALSafe service due date or disable this function using the RD Manager
PC software. Refer to its operation manual for further information.
Automatic Logging
RD8000 logging and GPS locator models offer a powerful data logging system which
records all the instrument’s critical parameters (including GPS position, if available) and
warnings in its internal memory at the rate of 1/sec.
The automatic logging system is always active and cannot be disabled. Its memory is
capable of storing at least 1 year’s worth of normal usage data – based on 4 hours
operation per day, 5 days per week, 20 days per month.
Logs can be retrieved using the RD Manager PC application for usage analysis and
survey validation. Refer to its operation manual for further information.
GPS
The RD8000 locator can be paired to an external GPS module or use its internal GPS
module (GPS models only) to be able to detect and store its latitude, longitude and
accurate UTC time alongside its location data using SurveyCERT or the automatic
logging system (GPS and logging models only).
The presence of GPS data allows for the data to be mapped easily and to export and
save the information directly into GIS systems.
GPS menu
To enter the GPS menu:
1. Press the key to enter the menu.
2. Scroll to the GPS menu using the or keys.
3. Press the key to enter the GPS menu.
There are 5 options:
• RESET: Select YES to reset the internal GPS (GPS models only).
• INT: Select this to use the internal GPS if present.
• EXT: Select this to use the GPS from a compatible paired device.
• OFF: Select this to switch off the internal GPS module and save battery.
• SBAS: Set SBAS (Satellite-based augmentation systems) mode to improve
GPS accuracy (North America only). When ON the GPS system will take
longer to lock.
4. Press the key to accept your changes and exit the GPS menu.
5. Press the key to exit the menu.
Important notices
When reporting any problems to your Radiodetection Dealer or Supplier it is important to
quote the unit serial number and the purchase date.

ENGLISH
26 27
This instrument, or family of instruments, will not be permanently damaged by reasonable
electrostatic discharge and has been tested in accordance with IEC 801-2. However,
in extreme cases temporary malfunction may occur. If this happens, switch off, wait and
switch on again. If the instrument still malfunctions, disconnect the batteries for five
seconds and then reinstall and switch the unit on.
Compliance
EU Compliance
This equipment complies with the following EU Directives:
• R&TTE Directive: 1999/5/EC
• Low Voltage Directive: 2006/95/EC
• EMC Directive: 2004/108/EC
FCC Compliance Statement
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
• The equipment may not cause harmful interference.
• The equipment must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause
harmful interference with radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case you will be
required to correct the interference at your own expense.
Modifications:
Any modifications made to this equipment not approved by Radiodetection may void the
authority granted to the user by the FCC to operate this equipment.
Industry Canada Compliance Statements
ICES-003 Class A Notice:
This Class A digital apparatus complies with Canadian ICES-003.
Avis NMB-003, Classe A: Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
Training
Radiodetection provides training services for most Radiodetection products. Our qualified
instructors will train equipment operators or other personnel at your preferred location or
at Radiodetection headquarters. For more information go to www.radiodetection.com or
contact your local Radiodetection representative.
Care and maintenance
The RD8000 locator and transmitter are robust, durable and weatherproof. However you
can extend your equipment’s life by following these care and maintenance guidelines.
General
Store the equipment in a clean and dry environment.
Ensure all terminals and connection sockets are clean, free of debris and corrosion and
are undamaged.
Do not use this equipment when damaged or faulty.
Batteries and power supply
Use good quality Alkaline or NiMH batteries only.
When using an AC adapter, use only Radiodetection approved adapters.
Only use Radiodetection approved Li-Ion battery packs.
Batteries should be disposed of in accordance with your company’s work practice, and/
or any relevant laws or guidelines in your country.
Cleaning
WARNING! Do not attempt to clean this equipment when it is powered or
connected to any power source, including batteries, adapters and live cables.
Ensure the equipment is clean and dry whenever possible.
Clean this equipment with soft, moistened cloth.
If using this equipment in foul water systems or other areas where biological hazards may
be present, use an appropriate disinfectant.
Do not use abrasive materials or chemicals as they may damage the casing, including the
reflective labels.
Do not use high pressure hoses.
Disassembly
Do not attempt to disassemble this equipment under any circumstances. The locator and
transmitter contain no user serviceable parts.
Disassembly may damage the equipment and or reduce its performance and may void the
manufacturer’s warranty.

ENGLISH
28 29
Service and maintenance
The locator and transmitter are designed so that they do not require regular calibration.
However, as with all safety equipment, it is recommended that they are serviced at least
once a year either at Radiodetection or an approved repair center.
Regularly check your equipment using eCert; this automatic validation test ensures the
equipment is valid according to its original factory calibration.
NOTE: Service by non-approved service centers or operators may void the
manufacturer’s warranty.
Radiodetection products, including this guide, are under continuous development and are
subject to change without notice. Go to www.radiodetection.com or contact your local
Radiodetection representative for the latest information regarding the RD8000 locator or
any Radiodetection product.
RD Manager
The RD Manager is the RD8000 locator system PC companion and it allows you to
manage and customize your locator. It also allows software upgrades to both the locator
and transmitter.
You can use RD Manager to register your products to obtain 2 years extended warranty,
setup your locator by performing a number of maintenance tasks such adjusting date
and time, activating and de-activating active frequencies or RF markers, or by setting-up
functions like CALSafe or StrikeAlert.
RD Manager is also used to retrieve and analyze surveys data and internal logged data
(logging and GPS models only).
RD Manager is compatible with PCs running Microsoft Windows XP, Vista, Windows 7
and Windows 8.
For more information about RD Manager refer to its operation manual.
To obtain RD Manager:
1. Go to www.radiodetection.com/RDManager.
2. Follow the instructions.
Software Upgrades
From time to time, Radiodetection may release software upgrades to enhance features
and improve performance of the RD8000 locator or transmitter.
Software upgrades are free of charge.
You can check if your products are up-to-date or upgrade them by using the RD Manager
software upgrade screen. Refer to its operation manual for further information.
E-mail alerts and notification of new software releases are sent to all registered users.
NOTE: To upgrade your products software you need to have created an
account using RD Manager and you need a live internet connection. An optional
Radiodetection power supply may be required to update your transmitter software.
eCert
The RD8000 locator is safety equipment which should be regularly checked to ensure its
correct operation.
eCert provides a thorough test of the RD8000’s locating circuitry and marker transceiver,
and supplies a Radiodetection Calibration Certificate when a positive test result is
obtained.
To run eCert, the locator should be connected to an internet-enabled PC on which the
RD Manager software is installed. Additional purchase may be required.
Refer to the RD Manager operation manual for further details.
NOTE: eCert can only be used with the locator.
Warranty and extended warranty
RD8000 locators and transmitters are covered by a 1 year warranty as standard.
Customers can extend the warranty period to a total of 3 years by registering their
products (locators and transmitters) within 3 months of purchase.
Registration is carried out using the RD Manager PC software.
From time to time Radiodetection may release new software to improve the performance or
add new functionality to its products. By registering, users will benefit from subscribing to
email alerts advising about any new software and special offers related to its product range.
Users will be able to opt out at any moment from receiving software and technical
notifications or just from receiving marketing material.
Registering using email
You can also register your product(s) by sending an email to [email protected].
You will need to provide the following compulsory details:
1. Date of Purchase.
2. Serial Number of each of your qualifying products (RD8000 locators and
transmitters).
3. Your email address.
4. Your Company Name.
5. Contact Name.
6. Address.
7. Telephone Number.

ENGLISH
30 31
8. Country of residence.
9. Indicate that you do not wish to receive e-mail alerts advising about any new software
release (OPT OUT) – by default you will receive email notifications.
10. Indicate that you do not wish to receive e-mail or other marketing material with new
product information or special offers and promotions related to its product range
(OPT OUT) – by default you will receive marketing material.
Standard Warranty Terms
Subject to the conditions set out herein, Radiodetection Limited expressly and exclusively
provides the following warranty to original end user buyers of Radiodetection products.
Radiodetection hereby warrants that its products shall be free from defects in material
and workmanship for one year starting from point of sale to end customer. Extensions of
this warranty period are available where the same terms and conditions apply.
Statement of warranty conditions
The sole and exclusive warranty for any Radiodetection product found to be defective
is repair or replacement of the defective product at Radiodetection’s sole discretion.
Repaired parts or replacement products will be provided by Radiodetection on an
exchange basis and will be either new or refurbished to be functionally equivalent to new.
In the event this exclusive remedy is deemed to have failed of its essential purpose,
Radiodetection’s liability shall not exceed the purchase price of the Radiodetection
product. In no event will Radiodetection be liable for any direct, indirect, special,
incidental, consequential or punitive damages (including lost profit) whether based on
warranty, contract, tort or any other legal theory.
Warranty services will be provided only with the original invoice or sales receipt
(indicating the date of purchase, model name and dealer’s name) within the warranty
period. This warranty covers only the hardware components of the Radiodetection
product. Data storage media or accessories must be removed prior to submission of the
product for warranty service.
Radiodetection will not be responsible for loss or erasure of data storage media
or accessories. Radiodetection is not responsible for transportation costs and
risks associated with transportation of the product. The existence of a defect shall
be determined by Radiodetection in accordance with procedures established by
Radiodetection.
This warranty is in lieu of any other warranty, express or implied, including any implied
warranty of merchantability or fitness for a particular purpose.
©2017 Radiodetection Ltd. All rights reserved. Radiodetection is a subsidiary of SPX Corporation. RD8000, SurveyCERT, eCert,
StrikeAlert, SideStep, CALSafe, iLOC, flexiprobe, GatorCam, flexitrax and Radiodetection are either trademarks of Radiodetection in the
United States and/or other countries. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks
by Radiodetection is under license. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries. Due to a policy of continued development, we reserve the right to
alter or amend any published specification without notice. This document may not be copied, reproduced,
transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection Ltd.
This warranty does not cover:
a. periodic maintenance and repair or parts replacement due to wear and tear
b. consumables (components that are expected to require periodic replacement during
the lifetime of a product such as non-rechargeable batteries, bulbs, etc.)
c. damage or defects caused by use, operation or treatment of the product inconsistent
with its intended use
d. damage or changes to the product as a result of:
i. misuse, including: - treatment resulting in physical, cosmetic or surface damage or
changes to the product or damage to liquid crystal displays
ii. failure to install or use the product for its normal purpose or in accordance with
Radiodetection’s instructions on installation or use
iii. failure to maintain the product in accordance with Radiodetection’s instructions
on proper maintenance
iv. installation or use of the product in a manner inconsistent with the technical or
safety laws or standards in the country where it is installed or used
v. virus infections or use of the product with software not provided with the product
or incorrectly installed software
vi. the condition of or defects in systems with which the product is used or
incorporated except other ‘Radiodetection products’ designed to be used with
the product
vii. use of the product with accessories, peripheral equipment and other products of
a type, condition and standard other than prescribed by Radiodetection
viii. repair or attempted repair by persons who are not Radiodetection warranted and
certified repair houses
ix. adjustments or adaptations without Radiodetection’s prior written consent,
including:
i. upgrading the product beyond specifications or features described in the
instruction manual, or
ii. modifications to the product to conform it to national or local technical or
safety standards in countries other than those for which the product was
specifically designed and manufactured
x. neglect e.g. opening of cases where there are no user replaceable parts
xi. accidents, fire, liquids, chemicals, other substances, flooding, vibrations, excessive
heat, improper ventilation, power surges, excess or incorrect supply or input
voltage, radiation, electrostatic discharges including lighting, other external forces
and impacts.

DEUTSCH
32 33
Einleitung
Über diese Anleitung
Vorsicht: In diesem Leitfaden werden die wesentlichen Bedienungsabläufe
für den Empfänger RD8000 mit Sender beschrieben. Er enthält außerdem
wichtige Sicherheitsinformationen und -richtlinien. Deshalb muss er komplett
durchgelesen werden, bevor der Empfänger RD8000 mit Sender verwendet wird.
Dieser Leitfaden ist nur als Kurzübersicht zum Mitführen gedacht. Für detailliertere
Informationen, einschließlich für den Einsatz von Zubehör, Hilfe bei eCert™, CALSafe™*,
SurveyCERT™und automatischer Protokollierung*; nutzen Sie bitte die RD8000
Bedienungsanleitung, SurveyCERT und RD-Manager™Beschreibungen, welche als
Download unter www.radiodetection.com zur Verfügung steht.
Die Online-Bibliothek enthält auch Links zu SurveyCERT und RD-Manager
Beschreibungen.
*Nur für Protokollierung und GPS-Modelle.
WARNUNG! Ein direkter Anschluss an stromführende Leitungen ist
LEBENSGEFÄHRLICH. Direkte Anschlüsse dürfen nur durch Fachpersonal
hergestellt werden.
WARNUNG! Der Sender kann lebensgefährliche Spannungen freigeben.
Seien Sie vorsichtig beim Anlegen von Signalen. Bitte informieren Sie alle
Techniker, die diese Linie nutzen.
WARNUNG! Reduzieren Sie die Lautstärke bevor Sie den Kopfhörer nutzen,
um Ihre Ohren zu schützen.
WARNUNG! Das System ist NICHT für Einsätze in explosionsgefährdeten
Bereichen zugelassen.
WARNUNG! Bei Verwendung des Senders das Gerät ausschalten und die
Kabel abziehen, bevor der Akkupack entfernt wird.
WARNUNG! Das RD8000 erkennt praktisch alle unterirdisch verlegten Leiter.
Es gibt jedoch Objekte, die kein erkennbares Signal senden. Das RD8000 oder
andere elektromagnetische Ortungsgeräte können diese Objekte nicht erkennen.
Gehen Sie daher mit Vorsicht vor. Es gibt auch stromführende Kabel, die das
RD8000 im Strombetrieb nicht erkennen kann. Das RD8000 zeigt nicht an, ob ein
Signal von einem Einzelkabel oder von mehreren Kabeln in unmittelbarer Nähe
kommt.
WARNUNG! Die Batterien können bei voller Nutzung heiß werden. Seien Sie
vorsichtig beim Ersetzen oder Handhabung der Batterien.
Erweiterte Garantie
Vielen Dank für den Kauf des Empfängers RD8000 mit Sender.
Die Garantiezeit für den Empfänger RD8000 mit Sender beträgt 1 Jahr.
Kunden können ihr Produkt (Empfänger und Sender) durch Registrierung die
Garantiezeit auf 3 Jahre verlängern.
Die Registrierung kann mit der RD Manager Software durchgeführt werden,
die Sie auf der Radiodetection Website downloaden können. Besuchen Sie
www.radiodetection.com/RDManager.
Von Zeit zu Zeit werden neue Softwareupdates zur Verbesserung der
Funktionalität von Radiodetection zur Verfügung gestellt. Nach erfolgter
Registrierung erhalten alle Anwender per E-Mail eine Mitteilung über spezielle
Angebote zur Produktgruppe.
Anwender sind somit in der Lage, jederzeit aktuelle Informationen über technische
Neuerungen zu erhalten.
eCert
Der RD8000 Empfänger ist eine Sicherheitsausrüstung, die regelmäßig überprüft
werden sollten, um die korrekte Funktion gewährleisten zu können.
eCert bietet eine gründliche Prüfung des RD8000, die die Ortungs-Schaltkreise
und Marker-Transceiver überprüft und bei positivem Testergebnis ein
Radiodetection Kalibrierungszertifikat ausstellt.
Damit eCert einwandfrei genutzt werden kann, sollte die RD-Manager-Software
auf einem internetfähigen PC installiert sein. Ggfs. ist ein separater Kauf
notwendig.
Nähere Details zum RD-Manager finden Sie in der detaillierten Bedienungsanleitung.

DEUTSCH
34 35
Empfänger RD8000
1
2
5
6
7
9
3
4
8
16 17 181822
10
11
12 13 14
1512
32
35
36
37
38
34
19
20
21
23
24
25 26 27 29 3033 3128
12 oder mehr Satelliten im Blick
9-11 Satelliten im Blick
6-8 Satelliten im Blick
3-5 Satelliten im Blick
GPS Satellitenanschluss erworben
GPS aktiv - sucht Satelittenanschluss
Empfänger Funktionen
1. Tastenfeld
2. LCD-Anzeige
3. Lautsprecher
4. Batteriefach
5. Batterieladeanschluss
6. Zubehöranschluss
7. Kopfhöreranschluss
8. Bluetooth-Modul-Antenne
9. Marker-Rahmenantenne
Tastatur Empfänger
10. Ein-/Ausschalttaste : Schaltet
die Einheit ein oder aus. Öffnet das
Empfänger-Menü.
11. Frequenz-Taste : Auswahl der
Frequenz. Schließen des Untermenüs.
12. Auf-/Ab-Pfeiltasten : Einstellen
der Signalstärke. Scrollen durch die
Menüoptionen.
13. Antennentaste : Auswahl Maximum-,
Minimum- oder Einzelantenne bzw. der
kombinierte Max/Min-Ortungsbetrieb.
Öffnen eines Untermenüs. Drücken und
Halten der Taste wählt die automatische
Anzeige der Tiefe oder des Stromes im
Display.
14. Grafik-Taste : Speichert die Messungen
durch SurveyCERT.
15. Sender-Taste : Sendet den iLOC™
Befehl, um die iLOC-Funktion zwischen
Sender und Empfänger zu aktivieren.
Bildschirmsymbole des
Empfängers
16. Anzeige der Signalstärke und der
Spitzenmarke
17. Signalstärke: Numerische Anzeige der
Signalstärke
18. Links-/Rechts-Proportional-Pfeile:
Anzeige der georteten Leitung mit
Entfernungsrelation zum Ortungsgerät
19. Batterieanzeige: Anzeige des
Akkuladestands
20. Empfindlichkeit und Aufzeichnungsnummer:
Kurze Anzeige der Signalverstärkung/-
empfindlichkeit oder der
Aufzeichnungsnummer nach Speicherung
einer Ortungsaufzeichnung
21. Lautstärkeanzeige: Anzeige der Lautstärke.
22. Stromrichtungspfeile: Für die Funktionen
CD und Fehlersuche
23. Radio-Modus: Anzeige bei aktivem Radio-
Modus
24. Strom-Modus: Anzeige bei aktivem Strom-
Modus.
25. Zubehör-Anzeige: Gibt an, wenn Zubehör
angeschlossen ist oder Messungen aktiv
sind.
26. CD-Betriebsanzeige: Erscheint, wenn der
CD-Betrieb gewählt wurde.
27. Anzeige der Rahmenantenne: Erscheint bei
angeschlossener Rahmenantenne.
28. Anzeige der Betriebsart / Menüanzeige
29. Bluetooth®-Anzeige: Versuchte
Verbindungsaufnahme wird durch Blinken
des Symbols angezeigt. Ein nicht blinkendes
Symbol zeigt eine aktive Verbindung an.
30. Antennen-Betriebsanzeige: Zeigt die Wahl
der Antenne an: Maximum-, Minimum- oder
Einzelantenne bzw. kombinierter Max/Min-
Ortungsmodus.
31. Sonden-Symbol: Zeigt an, dass
Sondenortung gewählt wurde.
32. Leitungsortungssymbol: Zeigt an, dass
Leitungsortung gewählt wurde.
33. Kompass/Marker: Zeigt die Richtung
des georteten Kabels in Relation zum
Ortungsgerät an. Wird auch als graphische
Indikation für aktiven Marker verwendet.
34. Sender-Status: Zeigt den
Verbindungsstatus zum Sender an (bei
iLOC-fähigen Modellen).
35. Sender-Standby: Zeigt an, dass sich der
Sender im Bereitschaftsbetrieb befindet
(bei iLOC-fähigen Modellen).
36. Strom-/Tiefen–Anzeige.
37. GPS-Statussymbol: Ein Balken zeigt an,
dass GPS aktiv ist. 3 Balken gibt an, dass
GPS gesperrt ist. Nur bei GPS-Modellen.
GPS-Signalqualität Symbol: Zeigt die
Qualität des empfangenen Signals – nur bei
GPS-Modelle.

DEUTSCH
36 37
Sender Tx-1, Tx-5 und Tx-10
1
3
2
10
11
12 13 14
15
16
17
18
19
20
21
22
5
4
6
7
8
9
Sender-Merkmale
1. Tastenfeld
2. LCD-Anzeige
3. Abnehmbare Zubehörbox
4. D-Zellen-Batterienfach
5. Akku-Pack (optional)
Sender-Tastenfeld
6. Ein-/Ausschalt-Taste : Ein-/
Ausschalten des Senders (lang
drücken) oder Zugang zum Sender-
Menü (kurz drücken). Öffnen des
Sender-Menüs.
7. Frequenz-Taste : Auswahl der
Frequenz Menü-Navigationstaste.
8. Auf-/Ab-Pfeiltasten : Einstellen
des Ausgangssignals / Scrollen durch
die Menüoptionen.
9. Mess-Taste : Öffnet ein Untermenü
und mißt die Spannung.
Bildschirmsymbole des
Senders
10. Batterieanzeige: Anzeige des
Akkuladestands
11. Alphanumerische Anzeige der
gewählten Einstellung
12. Bereitschaftssymbol: Erscheint,
wenn der Sender in den
Bereitschaftsbetrieb versetzt wurde.
13. Ausgangsleistung: Zeigt die
Ausgangsleistung des Senders an.
14. Zangensymbol: Erscheint, wenn
eine Zange oder ein anderer
Steckverbinder angeschlossen wird.
15. DC-Symbol: Erscheint, wenn der
Sender an eine Gleichstromversorgung
angeschlossen ist.
16. Induktionsanzeige: Erscheint, wenn der
Sender im Induktionsbetrieb arbeitet.
17. A-Rahmen (nur Tx-5 und Tx-10):
Erscheint, wenn der Sender im
Fehlersuchebetrieb ist.
18. CD-Betriebsanzeige (nur Tx-10):
Zeigt an, dass der Sender in den
Signalstromrichtungsbetrieb geschaltet
ist.
19. Spannungsanzeige: Zeigt an, dass
am Ausgang des Senders Spannung
anliegt.
20. Lautstärkeanzeige: Anzeige der
Lautstärke
21. Verbindungsanzeige (nur Tx-5B und
Tx-10B) Erscheint, wenn der Sender
und das Ortungsgerät über iLOC
verbunden sind.
22. Bluetooth-Anzeige (nur Tx-5B
und Tx-10B). Zeigt Bluetooth-
Verbindungsstatus an. Wenn das
Symbol blinkt, ist die Verbindung noch
im Aufbau.

DEUTSCH
38 39
Erste Schritte
WICHTIG! Dieser Leitfaden soll eine kurze Einführung sein. Wir empfehlen Ihnen,
die Bedienungsanleitung zu lesen, bevor Sie den RD8000-Empfänger benutzen!
Bei der ersten Verwendung
Aus Sicherheitsgründen werden RD8000 Empfänger getrennt von den Li-Ion-Akkus und
der Sender ohne D-Zellen im Batteriefach ausgeliefert.
Um die Li-Ion Batterien einzulegen, öffnen Sie das RD8000 Batteriefach und schließen
Sie das Batteriekabel an den Batterieanschluss an.
Damit die D-Zellen Batterien in den Sender passen, entriegeln Sie die Zubehörablage. Das
Batteriefach befindet sich unter dem Senderkörper. Verwenden Sie den Drehverschluss um
das Batteriefach zu entriegeln. Legen Sie acht D-Cell Alkaline-oder NiMH-Akkus ein.
Systemeinrichtung
Es ist wichtig, dass Sie das System nach Ihren persönlichen Vorlieben und
Betriebsanforderungen einstellen, bevor Sie Ihre erste Ortung durchführen. Sie können das
System einrichten über das Menü Marker RD8000-Empfänger wie unten beschrieben.
Hinweis: Dieses Verfahren bezieht sich sowohl auf den Sender und den Empfänger
sofern nicht anders angegeben.
Bevor Sie Einstellungen veränderen, schalten Sie den Empfänger oder den Sender an mit
der Ein-/Ausschalttaste .
HINWEIS: Wenn das System einmal eingeschaltet ist, drücken Sie die Ein-/
Ausschalttaste augenblicklich wird das Empfänger- oder Sender-Menü aktiviert.
Verwenden des Menüs
Über die Menüs des Empfängers RD8000 können Sie Systemoptionen wählen oder
ändern. In den Menüs verwenden Sie die Pfeiltasten zur Navigation. Die Navigation verläuft
bei Sender und Empfänger nach dem gleichen Schema. Beim Aufrufen des Menüs werden
die meisten Bildschirmsymbole vorübergehend ausgeblendet und die Menüoptionen
werden links unten auf dem LCD-Bildschirm angezeigt. Beachten Sie, dass die Tasten
und beim Durchsuchen als linke und rechte Pfeiltasten dienen. Beim Empfänger sind
die linken und rechten Pfeiltasten nur aktiv, wenn Sie sich im Menü befinden. Mit der
rechten Pfeiltaste öffnen Sie ein Untermenü und mit der linken Pfeiltaste übernehmen Sie
die Auswahl und kehren in das vorhergehende Menü zurück.
HINWEIS: Wenn Sie eine Option wählen und die linke Pfeiltaste drücken, wird die
Option automatisch aktiviert.
Menüoptionen am Empfänger
• VOL: Einstellen der Lautstärke von 0 (stumm) bis 3 (sehr laut).
• LOG oder DATA: Löschen, Senden oder Aufrufen von gespeicherten SurveyCERT.
• BT: Einschalten, Ausschalten, Zurücksetzen oder Verbinden über Bluetooth.
• GPS: Wählen Sie ein externes GPS-Modul oder aktivieren oder deaktivieren Sie das
interne GPS-Modul(nur bei GPS-Modelle).
• CDR: CD-Reset. Nur verfügbar, wenn im CD-Modus.
• UNITS: Auswahl der Maßeinheit (metrisch oder imperial).
• CAL: Anzeige des Datums der ursprünglichen Werkskalibrierung und der aktuellsten
eCAL.
• MARKR: Aktivieren oder deaktivieren Sie einzelne Marker.
• LANG: Auswahl der gewünschten Sprache (DEU für Deutsch).
• POWER: Auswahl der örtlichen Stromfrequenz: 50 oder 60 Hz.
• ANT: Ein-/Ausschalten des Antennenbetriebs, mit Ausnahme der Spitzensignalortung.
• FREQ: Aktivieren bzw. Deaktivieren von individuellen Frequenzen.
• ALERT: Ein- bzw. Ausschalten von StrikeAlert™.
• BATT: Auswahl des Batterietyps: NiMH, ALK oder Li-ION.
• COMP: Einschalten oder Abschalten der Anzeige der Kompass-Funktion.
Navigieren im Empfängermenü:
1. Drücken Sie kurz die Taste , um das Menü zu öffnen.
2. Drücken Sie die oder -Tasten, um durch die Menüoptionen zu blättern.
3. Drücken Sie die Taste , um das gewünschte Untermenü zu öffnen.
4. Verwenden Sie die oder -Tasten, um durch die Untermenüoptionen zu blättern.
5. Mithilfe der Taste wird Ihre Auswahl bestätigt und Sie kehren zur vorherigen
Menüebene zurück.
6. Drücken Sie die Taste , um zum Hauptarbeitsbildschirm zurückzukehren.
Menüoptionen am Sender
• VOL: Einstellen der Lautstärke von 0 (stumm) bis 3 (sehr laut).
• FREQ: Aktivieren und Deaktivieren von individuellen Frequenzen.
• BOOST: Anheben der Ausgangsleistung für einen bestimmten Zeitraum (einstellbar
in Minuten).
• LANG: Auswahl der Sender-Systemsprache.
• OPT F: Ein-/Ausschalten der SideStepAuto™-Funktion.
• BATT: Auswahl des Batterietyps: NiMH, ALK oder Li-ION.
• MAX P: Auswahl der Ausgangsleistung.
• MODELL: Spezifiziert das Modell Ihres RD8000 Ortungsgeräts.
• MAX V: Auswahl der Ausgangsspannung.
• BT: Aktivieren, Deaktivieren oder Herstellen der Bluetooth-Verbindungen (nur bei BT-
Versionen verfügbar).