RadiSys PM6264S ONT User manual

Quick
Installation Guide
PM6264S ONT
Document Revision 0.1 (draft)

© Copyright 2023. Radisys Corporation, All Rights Reserved. 3
Radisys 6264S ONT Quick Installation Guide
2
Interfaces Specication
4 10/100/1000 Base-T ports (RJ45)
Wi-Fi 4x4/4x4 Wi-Fi 6 (internal antennas)
VoIP 2 FXS ports (RJ11)
USB USB 3.0 Type A
Power Adaptor Input 110-240VAC, 50/60Hz
Power Adaptor Output +12VDC nominal, 2A
Operating Temperature 5 to 40°C (41 to 104°F)
Operating Humidity 5 to 85% (non-condensing)
Dimensions 226 x 191 x 46 mm (W x D x H)
2.3 Interfaces
Item Description
1 LEDs Status LEDs
2 POWER Power port for external Power Adaptor
1 Introduction
The Radisys PM6264S XGS-PON Home Gateway Unit (HGU) is an advanced
Wi-Fi6 dual-band XGS-PON ONT complying with the ITU-T G.9807.1
standard via SFP+ pluggable interface. The gateway is best suited for FTTH
residential and small ofce use that requires optimal wireless coverage.
2.1 Contents
- PM6264S ONT
- Quick Installation Guide
- Power Adaptor
2.2 ProductSpecications
Interfaces Specication
WAN Uplink PON port (SC/APC)
Ethernet 1 100/1000/10G Base-T port (RJ45)
4.16mm
2mm
2mm
2mm
2mm
2mm
2mm
2mm
2mm
2mm
2mm
2mm
2mm
1

© Copyright 2023. Radisys Corporation, All Rights Reserved. 5
Radisys 6264S ONT Quick Installation Guide
4
Label Color Status Denition
INTERNET RED ON Loss of Signal (LOS) alarm
White ON Internet service available, IP address
Slow blink
(1000ms on,
666ms off)
Reset to factory defaults, not cong-
ured for service
Wi-Fi White ON 2.4GHz/5GHz Wi-Fi radio is enabled
with security
Slow blink
(1000ms on,
666ms off)
WPS push-button activated
Slow blink
(1000ms on,
666ms off)
Reset to factory defaults, not cong-
ured for service
OFF 2.4GHz/5GHz Wi-Fi radio is disabled,
WPS is not active
PHONE White ON Telephone port registered for service
Fast Blink
(1000ms off,
280ms on,
280ms off,
280ms on)
Telephone line is off hook
Slow blink
(1000ms on,
666ms off)
Reset to factory defaults, not cong-
ured for service
OFF Telephone port is disabled or un-reg-
istered
Item Description
3 ON/OFF Button Turn power ON or OFF
4 RESET Reboot ONT (quick push)
Reset to factory (press and hold for 10 seconds)
5 WPS Press to initiate WPS connection
6 Wi-Fi Press to initiate the WPS connection
6 USB USB port for ancillary equipment
7 10GE 10GE Ethernet ports for PC or LAN (RJ45)
8 GE 1-4 1GE Ethernet ports for PC or LAN (RJ45)
9 TEL 1 Phone port for telephony (RJ11)
2.4 LED Status Indicators
Label Color Status Denition
POWER White ON Normal operation
Slow blink
(1000ms on,
666ms off)
Reset to factory defaults, not cong-
ured for service
Slow blink
(1000ms on,
666ms off)
Initializing, start of boot process

© Copyright 2023. Radisys Corporation, All Rights Reserved. 7
Radisys 6264S ONT Quick Installation Guide
6
Label Color Status Denition
WPS Green Slow Blink (1/s) WPS push-button activated
OFF WPS is not active
PHONE Green ON Telephone port registered for service
Slow Blink (1/s) Telephone line is off hook
OFF Telephone port is disabled or un-reg-
istered
USB Green ON Device is connected to USB port
OFF No device connected
3.1 Installation
1. Remove ONT from packaging.
2. Lay ONT at on surface or attach ONT to wall.
3. Remove protection plug (black) from WAN port.
4. Connect ber optic cable with SC/APC termination to WAN port.
5. Connect telephone cable (5) with RJ11 termination to PHONE.
6. Connect Ethernet cable (6) with RJ45 termination to 10G LAN
and LAN 1-4. Recommend CAT6 or better Ethernet cable for
10GE port.
7. Connect Power Adaptor cable (7) with 2-pin barrel to POWER port.
8. Plug in Power Adaptor into electrical outlet.
9. Push ON/OFF button. Check LED power up sequence.
User note: ONT may be upgraded to newer software image prior to
provisioning of services. ONT may reset after initial boot up sequence is
complete or software image is upgraded.
Label Color Status Denition
MOBILE White Fast Blink
(1000ms off,
280ms on,
280ms off,
280ms on)
Voice ports in use (VoCS), Incoming
Call, Outgoing Call, Call established.
Slow blink
(1000ms on, 666ms
off)
Network detected.
BACKUP MODE
ON Data connection established.
BACKUP MODE
Red Slow blink
(1000ms on,
666ms off)
Attempting to set up mobile con-
nection. Stick pending PIN or PUK.
BACKUP MODE
OFF 2.4GHz Wi-Fi radio is disabled
5GHZ Green ON 5GHz Wi-Fi radio is enabled
Slow Blink (1/s) 5GHz Wi-Fi radio transmitting data
trafc
OFF 5GHz Wi-Fi radio is disabled
76
5

© Copyright 2023. Radisys Corporation, All Rights Reserved. 9
Radisys 6264S ONT Quick Installation Guide
8
3.2 Mounting ONT on a wall
ONT has two mounting holes that can be used for wall mount placement.
Please see diagram for screw separation and location.
ONT should be mounted with LEDs facing up and service interfaces facing
down to avoid dust and contamination.
4 Web Graphical User Interface
You can access the ONT through a web browser using the following steps:
- Connect an Ethernet cable from your computer to any of the 10G
or LAN 1 - 4 ports.
- Launch a web browser or telnet session and connect to a
ddress 192.168.1.1.
- After response, enter the following:
1. Username : user
2. Password: user
After initial login, it is recommended that password be changed.

© Copyright 2023. Radisys Corporation, All Rights Reserved. 11
Radisys 6264S ONT Quick Installation Guide
10
6 Limited Warranty5 Caution
Please follow the instructions below to avoid physical injury:
- This unit is for indoor use only.
- All Ethernet, telephone and power wiring are limited to inside
of the building.
- You should not install ONT during lighting storms to avoid
electrical shock.
- Never look directly at the ber port and ber cable ends when
they are powered on.
- DO NOT plug in, turn on or attempt to operate an obviously
damaged unit.
- DO NOT use near water.
- DO NOT operate ONT in a location where maximum ambient
temp. exceeds 40°C.
- DO NOT place near high temperature source.
- Set up the unit away from direct sunlight or other electrical
equipment.
- Open optical connections must use a protective cap under all
circumstances to protect against physical damage and dirt.
- Avoid impact stresses when handling connectors.
- Physical damage to optical connections impairs transmission quality.
- Avoid a bend radius in excess of 30 mm for ber optic links.
- Check the available voltage supply.
- Only connect approved accessories.
- This equipment is not suitable for use in locations where children
are to be present.
- DO NOT disassemble the unit.
The product warranty does not cover damage resulting from hardware
being installed in areas subject to rain, high humidity, water ingress and
dust or debris. Disassembling product or removing enclosure cover from
the assembly is a safety hazard and will void warranty. PM6264S may only
be repaired by authorized service personnel.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 25 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation
statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
Canada Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can
obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf,
utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and
operated with a minimum distance of 25 centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être
installé et actionné avec une distance minimum de 25 centimètres entre le radiateur et votre corps.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile
satellite systems
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

Radisys 6264S ONT Quick Installation Guide
12
RSYSQG6264SONT12062023A