RADSON TEMPCO Series User manual

A
B
M16MI345 A04-06/18
EN MAINTENANCE MANUAL
FR NOTICE D’UTILISATION
NL HANDLEIDING
DE BEDIENUNGSANLEITUNG
TEMPCO RF CONTROL
(Deco_Delta)

SYNOPSIS
PRECAUTIONS .................................................................................................................................................................................................................................4
INTRODUCTION..............................................................................................................................................................................................................................5
INSTALLATION .................................................................................................................................................................................................................................5
Location.............................................................................................................................................................................................................................................5
Electrical connection ....................................................................................................................................................................................................................5
Particular recommendations.....................................................................................................................................................................................................5
STARTING THE SYSTEM................................................................................................................................................................................................................6
Receiver .............................................................................................................................................................................................................................................6
Receiver indicator light status...................................................................................................................................................................................................6
Transmitter ......................................................................................................................................................................................................................................7
DESCRIPTI ON OF TRANSMITTER MODES (REMOTE CONTROL)...................................................................................................................................
Confort ..............................................................................................................................................................................................................................................7
Auto....................................................................................................................................................................................................................................................7
Eco.......................................................................................................................................................................................................................................................8
Anti Frost ..........................................................................................................................................................................................................................................9
Vacation ............................................................................................................................................................................................................................................9
Boost ..................................................................................................................................................................................................................................................9
Timer Program operating mode ...............................................................................................................................................................................................10
Locking the keypad........................................................................................................................................................................................................................11
Open window detection .............................................................................................................................................................................................................11
Factory settings..............................................................................................................................................................................................................................11
ADVANCED SETTINGS .................................................................................................................................................................................................................11
Fan installed ....................................................................................................................................................................................................................................11
Pairing menu...................................................................................................................................................................................................................................12
Ambient temperature,.................................................................................................................................................................................................................12
Adaptative Smart time ................................................................................................................................................................................................................12
Open window detection: ............................................................................................................................................................................................................12
Setpoint temperature. .................................................................................................................................................................................................................12
Radiator sensor / Remote control sensor ..............................................................................................................................................................................12
Setpoint temperature regulation.............................................................................................................................................................................................12
Limit the surface temperature..................................................................................................................................................................................................12
Room sensor calibration..............................................................................................................................................................................................................12
Time....................................................................................................................................................................................................................................................12
Reset your remote control, .........................................................................................................................................................................................................12
Software version, ...........................................................................................................................................................................................................................12
MAINTENANCE, REPAIR AND REMOVAL...............................................................................................................................................................................13
Important.........................................................................................................................................................................................................................................13
Cleaning............................................................................................................................................................................................................................................13
Replacing remote control batteries.........................................................................................................................................................................................13
WARRANTY......................................................................................................................................................................................................................................13
TECHNICAL DATA...........................................................................................................................................................................................................................13
2
EN

a- Comfort symbol
b- Auto symbol
c- Eco symbol
d- Anti-frost symbol
e- Vacation symbol
f- Boost symbol
g- Timer program symbol
h- Day of the week
i- Heating indicator
j- Fan indicator
k- Open window detection indicator
l- Battery low indicator
m- Indicator for WiFi transmission/paired with
radiator/paired with E3 program controller
(sold separately)
n- Timer program indicator (d1 to d9, U1 to U4)
o- Exemption indicator
p- Installer menu indicator
q- Screen locked indicator
r- 24-hr timer program indicator
s- Setpoint or ambient temperature indicator
t- Ambient temperature indicator
ABCD E F
H I
J
K
L
M
G
N
O P
Q
R
S
T
Power adapter
(sold separately)
3
EN

CAUTION - CERTAIN PARTS OF THIS PRO-
DUCT CAN BECOME VERY HOT AND CAUSE
BURNS. YOU MUST PAY PARTICULAR ATTEN-
TION WHEN IN THE PRESENCE OF CHILDREN
AND VULNERABLE PEOPLE.
CHILDREN AGED BETWEEN 3 AND 8 YEARS
MUST ONLY SWITCH THE APPLIANCE ON OR
OFF ON CONDITION THAT IT IS PLACED OR
INSTALLED IN A NORMAL LOCATION AND
THE CHILDREN ARE PROPERLY SUPERVISED
OR HAVE BEEN INSTRUCTED IN PROPER SAFE
USE OFTHE APPLIANCE AND FULLY UNDERS-
TAND THE POTENTIAL DANGERS IT REPRE-
SENTS. CHILDREN UNDER 3 YEARS SHOULD
BE KEPT AWAY FROM THE APPLIANCE UN-
LESS UNDER CONSTANT SUPERVISION. KEEP
THE APPLIANCE AND ITS CABLE OUT OF THE
REACH OF CHILDREN UNDER 8 YEARS.
CHILDREN AGED BETWEEN 3 AND 8 YEARS
MUST NOT CONNECT, ADJUST OR CLEAN
THE APPLIANCE, NOR PERFORM USER MAIN-
TENANCE. THIS APPLIANCE CAN BE USED BY
CHILDREN OF 8 YEARS AND ABOVE AND BY
PEOPLE WITH REDUCED PHYSICAL, SENSO-
RY OR MENTAL CAPABILITIES OR WITH NO
EXPERIENCE OR KNOWLEDGE, IF THEY ARE
PROPERLY SUPERVIZED OR IF THEY HAVE
BEEN GIVEN INSTRUCTIONS RELATING TO
SAFE USE OFTHE APPLIANCE AND IF THE PO-
TENTIAL RISKS HAVE BEEN UNDERSTOOD.
CHILDREN MUST NOT PLAY WITH THE AP-
PLIANCE.
CLEANING AND MAINTENANCE BY THE
USER MUST NOT BE PERFORMED BY CHILD-
REN WITHOUT SUPERVISION. IF THE POWER
CABLE IS DAMAGED, IT MUST BE REPLACED
BY THE MANUFACTURER, ITS AFTER-SALES
SERVICE OR SIMILARLY QUALIFIED PERSONS
IN ORDER TO AVOID DANGER. A HEATING
APPLIANCE MUST NOT BE LOCATED DIREC-
TLY UNDER A POWER SOCKET. ALL MAIN-
TENANCE ON THE APPLIANCE MUST BE
CARRIED OUT WHEN SWITCHED OFF BY A
QUALIFIED PROFESSIONAL.
PRECAUTIONS
CONNECTION MUST BE MADE USING AN
OMNIPOLAR CIRCUIT BREAKER DEVICE.
CONTACTS MUST BE SEPARATED BY A DIS-
TANCE OF AT LEAST 3 MM.
TO AVOID OVERHEATING, DO NOT COVER
THE HEATING APPLIANCE! «DO NOT COVER»
MEANS FOR EXAMPLE THAT THE RADIATOR
MUST NOT BE USED TO DRY CLOTHES PLACED
DIRECTLY ONTO THE RADIATOR.
GESTION dES déchETS dES équIpEmENTS élEcTrIOuES ET
ÊLECTRONIOUES CONFORMÉMENT À LA DIRECTIVE
DEEE (2012/19/EU)
The symbol marked on the product’s label means
that the equipment must not be disposed of with
other waste, and that it is subject to selective collec-
tion aimed at its recovery, reuse or recycling. At the
end of its life, this equipment must be returned to
an appropriate collection point for the treatment of
electrical and electronic waste. By complying with
these principles and not throwing the product out
with other household waste, you are contributing to
conserving natural resources and protecting human
health. For any information concerning collection,
treatment, recovery and recycling points, please
contact your local authority or local waste collection
department, or even the retailer where you pur-
chased the equipment. This applies to the countries
in which this directive is in force.
4
EN

See the assembly instructions for attaching the radiator to the
wall. It is important that the thermostat is never placed directly
on the ground as there is a risk of breakage.
The remote control must preferably be installed on an interior
wall, at approximately 1.5 m from the ground, protected from wa-
ter spray, direct sunlight or any other direct thermal interference
such as a lamp, television set, heati ng pipe, draft , etc.
Electrical installati on must comply with local or
nati onal regulati ons. The radiator must be connected using the
original power cable att ached to the appliance. If the radiator
isinstalled in a bathroom or shower room, it must be protected
using a circuit breaker (RCD) with a nominal residual current
notexceeding 30 mA. The radiator must be connected by a
competent and quali ed electrician. Please refer to the cabling
diagram below.
LOCATION
INTRODUCTION
This appliance is a sealed electrical or mixed radiator designed
to be installed on a wall. It complies with NF-EN 60335-1 and EN
60335-2-30 standards as well as European EMC Directi ve 2014/30/
EU and Low Voltage Directi ve 2014/35/EU (CE labeling on all ap-
pliances). It is class II with IP44 protecti on index, and also complies
with European ECO Design Directive. This appliance is supplied
with a 3-wire power cable.
This radiator is tted with a 868.3 MHz radio-frequency receiver
(thermostat) which is designed to provide comfort and save ener-
gy. It is designed to be remote controlled by a transmitter (remote
control) with programmable digital display. This operati ng mode
using radio-frequency allows you to control several radiators, adjust
the ambient temperature directly or through the use of another
operati ng mode. It is possible to adjust the ambient temperature
via the sensor located in the transmitter or receiver.
By default, the temperature is adjusted by the sensor located in the
receiver.
INSTALLATION
PARTICULAR RECOMMENDATIONS
ELECTRICAL CONNECTION
Electric radiators (BAYO ONLY):
During operation, you may notice that some higher and lower ele-
ments are warmer than the rest of the radiator.
o Higher elements are not completely lled to allow expansion of
the heat-carrying liquid during the heating phase.
o Lower elements receive liquid returning aft er transmitting its
heat load.
5
EN

Receiver indicator light status
Operating mode Indicator status
Radiator paused
Indicator status
Radiator Heating up
Standby Off
Confort Steady green Steady red
Eco Flashing green Flashing red-green
Anti-frost Slow ashing green Slow ashing red-
green
Confort -1°C (*) Double ashing green Double ashing
redgreen
Confort -2°C (*) Double slow ashing
green
Double slow ashing
red-green
Pairing mode Flashing Orange Flashing orange
Sensor fault or
Measured temp. > 35°C
Flashing red --
The RF receiver is tted with an independent regulation system which saves status informati on (start/standby) and tem-
perature setpoints to its memory. Storage of the last received setpoint ensures the temperature is still regulated even if
the transmitter is turned off or its batteries exhausted. Also note that during a power outage to the radiators, pairing does
not need to be reiniti alized.
Important: If your receiver is turned off , your radiator will not receive any commands from the remote control.
Status of 2c signal
Off Surface temperature limitation is not activated
Steady green Surface temperature limitation is not activated
Triple fast ashing red IWiFi communications with transmitter indicator
Status of 2b and 2c signal
«2b» et «2c» ashing green alernately The receiver was sucessfully reset
«2b» et «2c» ashing orange alternately WiFi communications error
STARTING THE SYSTEM
RECEIVER
Connect your appliance to the electricity supply. Press butt on «B» located on the receiver at the bottom of the appliance
to start the radiator. Indicator light «A» is illuminated and you will hear 2 short «beep» sounds. Pressing button «B» again
will turn off your radiator and produce a long «beep» sound. Indicator light «A» goes out, and no communication with the
remote control is possible.
6
EN

Remove the protective ap from the remote control batt
eries. During rst startup, the appliance starts in comfort
mode. When changing at batteries and a long period has
elapsed (more than 2 minutes), the appliance starts in the
previous operating mode.
The rst step is to adjust the time on your remote control.
This adjustment can be made from any mode and at any
time.
 Press and hold the OK butt on for 5 seconds unti l the time
appears. Release it then press the OK button again.
 The hour gure ashes. Use the «+ or -» buttons to adjust
then press OK to accept.
 The minute gure  ashes. Use the «+ or -» buttons to ad-
just then press OK to accept.
 The day of the week ashes. Use the «+ or -» buttons to
adjust then press OK to accept.
 The date ashes. Use the «+ or -» buttons to adjust then
press OK to accept.
 The month ashes. Use the «+ or -» buttons to adjust then
press OK to accept.
 The year ashes. Use the «+ or -» buttons to adjust then
press OK to accept.
You will now be returned to the previous mode after accep-
ting the nal setting. The time, date and year are now set on
your remote control. They will be used in Auto and Vacation
modes.
Note: Setting the time is not necessary if your remote
control is paired with the E3 program controller (sold separa-
tely), as the time is automatically synchronized.
To view the adjusted time, press and hold the OK butt on for
5 seconds unti l the time appears. It will remain displayed for
10 seconds before returning to the previous mode.
Important: You can always cancel the last setti ng by pres-
sing the Back button. Also note that if the screen’s back-
ground light is not turned on, simply press any button to
activate it.
To establish communications between the transmitter (Re-
mote Control) and the receiver (Thermostat) follow the ins-
tructions below. This operation is also known as pairing. The
radiator must be turned on.
On the thermostat:
Press and hold butt on «B» on the thermostat for 5 seconds.
Indicator light «A»  ashes orange slowly. This is the signal
to release button «B» as the radiator is now in pairing mode.
On the remote control:
1. Press and hold the OK butt on on the remote control for
10 seconds unti l the installer menu appears «bL no», the
symbol appears.
2. Press the « + » butt on once, «rF INI» appears on the
screen. You are now at the pairing menu.
TRANSMITTER
3. Press the «OK» butt on once, «INI» and the symbol
start ashing on the screen. Your radiator is currentl
4. You can pair another radiator by repeating the pre-
vious steps (On the thermostat and on the remote
control).
Note: You can access the installer menu from any
mode.
Important: If you have an E3 program controller (sold
separately) installed in your system, always pair the
remote control rst then the radiator in accordance
with the operati ng modes described above and in the
E3 instruction manual. Timer programming and vaca-
tion functions are handled by the E3 program control-
ler and these symbols disappear from the remote
control screen
COMFORT TEMPERATURE OPERATING
MODE
DESCRIPTION OF
TRANSMITTER
MODES (REMOTE CONTROL)
7
EN

AUTO TEMPERATURE OPERATING MODE
ECO TEMPERATURE OPERATING MODE
Designed to be used when people are occupying the room or
may soon be.
Select this mode using the "+ or -" buttons then press OK. The
temperature setpoint appears on the screen. To modifythis,
press the OK button again and the temperature ashes. Use
the "+ or -" butt on to adjust it then press OK to accept.
The ambient temperature appears for 10 seconds followed
again by the temperature setpoint. The temperature range can
be between 5.5°C and 30°C. A three-color visual behavior indi-
cator displays during adjustment to inform you which tempe-
rature ranges involve low, medium or high energy consumpti
on and allow you to save energy.
 Green: Low consumption, temperature between 5.5°C and
19°C
 Orange: Medium consumpti on, temperature between
19.5°C and 24°C
 Red: High consumpti on, temperature between 24.5°C and
30°C
This visual indicator allows the user to be aware of the risk
of excessive energy consumpti on when setting the comfort
temperature.
The temperature you have set it to is the desired room tempe-
rature for this operating mode. You need to wait several hours
for the room temperature to become stable again.
Pressing the back button displays the ambient temperature in
the room for 10 seconds, the symbol also displays.
Designed to be used when people require automatic and
independent radiator operation as follows:
 Priority 1: If the radiator is connected, control is via the
cable: Commands sent by EDF as part of an off -peak
contract such as Tempo or other "6 level" energy manager,
the temperature is adjusted based on the comfort mode
temperature setpoint.
 Priority 2: The program currently set on the E3 program
controller (sold separately) if the remote control is paired
with it.
 Priority 3: A program previously selected in program
mode on the remote control (d1 to d9, U1 to U9).
You can at any time change the temperature setpoint in
your program by pressing the OK butt on. The temperature
then  ashes on the screen. Change it using the "+" and "-"
butt ons then press OK again to accept. In this case, you are
now in timer exemption and the symbol appears on the
screen. Pressing the butt on exits the exemption and re-
turns to the temperature setpoint for your program. If not,
the exemption exits automatically after 2 hours.
Pressing the back button displays the ambient temperature
in the room for 10 seconds, the symbol also displays.
Designed to be used when people are not occupying the
room or are unlikely to be.
Select this mode using the "+ or -" butt ons then press OK.
The temperature setpoint appears on the screen. To mo-
dify. this, press the OK butt on again and the temperature
ashes. Use the "+ or -" button to adjust it then press OK
to accept.
The ambient temperature appears for 10 seconds followed
again by the temperature setpoint. The temperature range
can be between 5.5°C and 19°C but always 0.5°C lower
than the comfort temperature.
The temperature you have set it to is the desired room
temperature for this operati ng mode. You need to wait
several hours for the room temperature to become stable
again.
Pressing the back butt on displays the ambient tempera-
ture in the room for 10 seconds, the symbol also displays.
8
EN

ANTI -FROST TEMPERATURE OPERATING
MODE
VACATION OPERATING MODE
BOOST OPERATING MODE
This mode prevents the system from freezing. It allows a mi-
nimum temperature to be maintained during a prolonged
absence.
Select this mode using the "+ or -" butt ons then press OK.
The temperature setpoint appears on the screen. To modify
this, press the OK butt on again and the temperature a-
shes. Use the "+ or -" button to adjust it then press OK to
accept.
The ambient temperature appears for 10 seconds followed
again by the temperature setpoint. The temperature range
can be between 5°C and 10°C.
Pressing the back butt on displays the ambient temperature
in the room for 10 seconds, the symbol also displays.
This function allows you to set your heating system to
your desired temperature while you are away and is set
using the following 4 steps:
1. Select this mode using the "+ or -" butt ons then press
OK. The temperature setpoint ashes on the screen.
Use the "+ or -" buttons to adjust the desired tempera-
ture to maintain during your absence and then press
OK to accept.
2. Now set the end date for your vacati on starting with
the month. Use "+ or - to adjust then press OK to ac-
cept. (Note: the year changes when you go below the 
rst month or above the twelft h.).
3. Set the day your vacati on ends. Use «+ or -» to adjust
then press OK to accept.
4. Set the time your vacati on ends. Use «+ or -» to ad-
just then press OK to accept. (Note: set to hours only);
Your vacation end date appears on the screen and the
vacation symbol ashes
You can exit vacation mode at any time by pressing the
back button for 2 seconds. You will be returned to the
previous mode.
This function allows you to manage rapid tem-
perature increases in your radiator at any time
and for a dened period without modifying your
programs.
Select this mode using the "+ or -" buttons then
press OK. A period of 30 minutes ashes on the
screen. Use the "+ or «-" buttons to adjust the
desired period in steps of 10 minutes. The set pe-
riod range can be between 10 and 120 minutes.
Press OK to accept.
9
EN

TIMER PROGRAM OPERATING MODE
The boost period countdown appears on the screen
and the symbol ashes. You can exit boost mode
at any time by pressing the back button. You will be
returned to the previous mode.
You can also access boost mode directly by pressing
the button on the remote control from any mode
except and . Then set the desired period and
accept as previously instructed.
This function allows you to set regulated tempera-
ture ranges according to the temperatures dened in
Comfort and Eco modes.
You will have a choice of 9 preset programs "d1" to
"d9" and 4 custom programs "U1" to "U4" to suit your
needs.
 If you choose a preset program:
1. Select this mode using the "+ or -" buttons then
press OK,
2. "d1" appears on the screen
3. Press OK, "d1"  ashes on the screen.
4. You can then choose another preset program using
the "+ or -" butt ons or keep this program. You have the
choice of 9 preset programs "d1" to "d9".
5. Press OK again to accept your choice. You will then
automati cally move into Auto mode (the temperature
setpoint and program number are displayed on the
screen).
List of preset programs and comfort mode operating
ranges.
o d1: Comfort mode all week.
o d2: Comfort mode 6:30 - 8:30 a.m. Monday to Friday
/ 8:30 - 10:30 a.m. at weekends.
o d3: Comfort mode 6:30 - 8:30 a.m. Monday to Friday
/ 8:30 - 10:30 a.m. and 7:00 - 9:00 p.m. at weekends.
o d4: Comfort mode 8:00 - 10:00 a.m. and 9:00 - 11:00
p.m. Monday to Friday / 9:00 - 11:00 a.m. and 9:00 -
11:00 p.m. at weekends.
o d5: Comfort mode 4:30 - 7:30 a.m. and 4:30 - 10:30
p.m. Monday to Friday / 7:00 - 11:00 p.m. at weekends.
o d6: Comfort mode 6:30 - 9:30 a.m. and 5:00 - 11:00
p.m. Monday to Friday / 8:00 a.m. - 11:00 p.m. at
weekends.
o d7: Comfort mode 6:30 - 8:30 a.m. and 12:00 - 2:00
p.m. and 5:00 - 11:00 p.m. Monday to Friday / 7:00 a.m.
- 11:00 p.m. at weekends.
o d8: Comfort mode 7:30 AM - 9:30 a.m. and 12:00 -
2:00 p.m. and 5:00 - 11:00 p.m. Monday to Friday / 8:00
a.m. - 11:00 p.m. at weekends.
o d9: Comfort mode 7:00 a.m. - 11:00 p.m. all week.
Notes: Preset ranges where your heating is in comfort
mode and the rest of the time in eco mode. Programs
d1 to d4 cover mainly radiators in a bathroom and pro-
grams d5 to d9 cover radiators in other rooms of the
house.
 If you choose a custom program:
1. Select this mode using the "+ or -" buttons then press
OK,
2. "d1" appears on the screen
3. Press OK, "d1" ashes on the screen.
4. You can then choose a custom program using the "+
or -" buttons. You have a choice of 4 custom programs
"U1" to "U4".
5. Press and hold OK for 2 seconds to access the pro-
gramming mode directly. The time 00:00 and the Eco
symbol ash on the screen. You can now customize
the program. You are at day 1 of the week (1=Monday).
6. Advance the time of day using the «+» button in steps
of 30 minutes to create your rst Eco mode period. Press
10
EN