RALPH RIEDL HIGHSTANDART STOIC BASIS User manual

PLEASE TAKE NOTE OF THE FOLLOWING GUIDELINES
Please read these instructions thoroughly before you begin
the assembly and installation.
Frame and board can be adjusted in height separately and
offer you a lot of flexibility and precision. Take yourself
some time to go through this initial installation process.
The metal parts and the support are heavy and can be
scratched easily if not handled with the required caution.
Additionally pay attention to the high risk of injury for
your feet caused by falling parts! Protect yourself with
the appropriate footwear (hard-toed safety shoes).
Make sure that the overall weight resulting from the
weight of the STOIC metal frame, the weight of the
support plate and your electronic device does not exceed
the load bearing capacity of your piece of furniture.
The STOIC Basis made from stainless steel was cleaned
before shipment to you. For this reason, the stainless steel
frame is only to be touched with gloves. Polished stainless
steel is tarnishing over time. If necessary, clean the frame
with a stainless steel cleaner.
A frame made of powder coated steel is best cleaned
with a damp cloth and a little detergent.
ASSEMBLYGUIDELINES
ASSEMBLY OF THE STOIC BASIS
Place the metal frame on a soft support to protect the table
top and the frame from scratching.
Start with placing the feet to the basis. The 8 mm machine
screw thread fits to the screw socket fixed on the triangle
console. Fix the spike feet with the M8 nuts from top. The
thread of the spike feet shall poke out of the nuts not more
than approximately 5 mm. Do not fully tighten the spike
feet yet.
Stick the self-adhesive felt lamination sheet underneath
the spike support disk.
Place the frame with its four spike feet carefully onto the
spike disks.
Use the spirit level to adjust the frame. Spin the spike
threads by use of the 4 mm Allen key and finally tighten
them with the 13 mm wrench.
Insert the four 6 mm steel spikes with the tip up into the
frame and fix them only slightly with the M6 nuts from
below.
Carefully place the support plate on the spikes. Before
placing a stone plate, protect the metal by placing soft
cloths over the frame.
Make sure that the 6 mm spikes slide into the spike
receptacles on the underside of the support plate.
If necessary, the spike positions must be corrected by
loosening and shifting.
Use the spirit level to adjust the support plate. To adjust the
6mm spikes, remove the support plate.
Finally, fix the 6mm spikes in the final position by tightening
the nut with the 10 mm wrench.
BASIS

TOOLS NEEDED
10 mm wrench
13 mm wrench
LIEFERUMFANG
metal frame, sand filled
support plate with spike receptacles
4 stainless steel spikes M6
4 stainless steel lock nuts M6 with washers
4 stainless steel screw nuts M6 for spikes
4 stainless steel spike feet M8
4 stainless steel lock nuts M8
4 stainless steel spike disks
4 self-adhesive felt lamination sheets for spike disks
precision spirit level
Allen 3 mm angle key
Allen 4 mm angle key
work gloves
TECHNICAL SPECIFICATIONS OF STANDARD MODELS
Outer mass = stand area:
400 mm × 550 mm / 500 mm × 550 mm
Weight (depending on size):
metal frame including sand filling: approx. 7 kg/ 8 kg
wooden plate: approx. 4.5 kg/ 5.5 kg
optional wooden plate with sand filling:
approx. 6 kg/ 7.7 kg
slate plate: approx. 18.5 kg/ 23 kg
Maximum load capacity: 100 kg
400 / 500 mm
550 mm
TOOLS
TECHNICAL
SPECIFICATIONS
www.highstandart.de
The frame and the support plate are completely
handmade. Slate and wood are natural products
with slight variations in the grain. This makes every
STOIC unique and distinguishes it from industrially
manufactured products.