RAMTONS RM/585 User manual

Air fryer
INSTRUCTION MANUAL
Model：RM/585
Read this manual thoroughly before using and save it for future reference

HOUSEHOLD USE ONLY
IMPROTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed
including the following:
1. Read all instructions.
2. Do not touch hot surfaces.
3. To protect against electric shock do not immerse cord, plugs, or housing in water or other
liquid.
4. WARNING: This electrical appliance contains a heating function. Surfaces, also different
than the functional surfaces, can develop high temperatures. Since temperatures are
differently perceived by different persons, this equipment shall be used with CAUTION. The
equipment shall be touch only at intended handles and gripping surfaces, and use heat
protection like gloves or similar. Surfaces other than intended gripping surfaces shall get
sufficiently time to cool down before getting touched.
5. Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or
taking off parts.
6. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
7. The use of accessory attachments not recommended by the appliance manufacturer may
cause injuries.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Extreme caution must be used when moving an appliance containing hot oil or other hot
liquids.
12. Always attach plug to appliance first, then plug cord in the wall outlet. To disconnect, turn
any control to "off," then remove plug from wall outlet.
13. Do not use appliance for other than intended use.
14. This appliance can be used by children aged from 8 years and above, and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning. use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children unless they are old than 8
and supervised.
15. Keep the appliance and its cord out of reach of children less than 8 years.
16. The appliances are not intended to be operated by means of an external timer or separate
remote-control system.

1
2
3
4
5
6
7
8
9
Fig.1
Fig.3
1
2
Fig.4
SAVE THESE INSTRUCTIONS
This appliance is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses;
- by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments.
Introduction
This Air fryer provides an easy and healthy way of preparing your favorite ingredients. By
using hot rapid air circulation, it is able to make numerous dishes. The best part is that the Air
fryer heats food at all directions and most of the ingredients do not need any oil.
General description (Fig.1)
1. housing
2. Power-on light
3. Touch control panel
4. pan
5. basket
6. Basket release button
7. Basket handle
8. Air outlet openings
9 .power cord
Fig.2

Fig.6
Fig.5
Important
Please read this manual carefully before you use the appliance and save it for future
reference.
Danger
-This appliance can be used by children aged from 8 years and above, and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning, use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children unless they are older than 8 and supervised.
-Keep the appliance and its cord out of reach of children less than 8 years.
-Never immerse the housing, which contains electrical components and the heating elements,
in water nor rinse it under the tap.
-Do not let any water or other liquid enter the appliance to prevent electric shock.
-Always put the ingredients to be fried in the basket, to prevent it from coming into contact with
the heating elements.
-Do not cover the air inlet and the air outer openings while the appliance is operating.
-Do not fill the pan with oil as this may cause a fire hazard.
-Never touch the inside of the appliance while it is operating.
The temperature of accessible surfaces may be high when the appliance is operating
Warning
- Check if the voltage indicated on the appliance fits the local mains voltage.
- Do not use the appliance if there is any damage on plug, mains cord or other parts.
- Do not go to any unauthorized person to replace or fix damaged main cord.
- Keep the mains cord away from hot surfaces.
- Do not plug in the appliance or operate the control panel with wet hands..
- Do not place the appliance against a wall or against other appliances. Leave at least 10cm
free space on the back and sides and 10cm free space above the appliance.

Do not place anything on top of the appliance.
- Do not use the appliance for any other purpose than described in this manual.
- Do not let the appliance operate unattended.
- During air frying, hot steam is released through the air outlet openings, Keep your hands and
face at a safe distance from the steam and from the air outlet openings.
Also be careful of hot steam and air when you remove the pan from the appliance.
-Any accessible surfaces may become hot during use (Fig.2)
- Immediately unplug the appliance if you see dark smoke coming out of the appliance. Wait
for the smoke emission to stop before you remove the pay from the appliance.
Caution
- Ensure the appliance in placed on a horizontal, even and stable surface.
- This appliance is designed for household use only. It may not suitable to be safely used in
environments such as staff kitchens, farms, motels, and other non-residential environments.
Nor is it intended to be used by clients in hotels, motels, bed and breakfasts and other
residential environments.
- If the appliance is used improperly or for professional or semi-professional purposes or if it is
not used improperly or for professional or semi-professional purposes or it is not used
according to the instructions in the user manual, the guarantee becomes invalid and we
could refuse any liability for damage caused.
-Always unplug the appliance while not using.
-The appliance needs approximately 30 minutes to cool down for handle or cleaning safely.
Before first use
1. Remove all packaging materials.
2. Remove any stickers or labels from the appliance .
3. thoroughly clean the basket and pan with hot water, some washing-up liquid and a
non-abrasive sponge.
Note: You can also clean these parts in the dishwasher.
4.Wipe inside and outside of the appliance with a moist cloth.
This is an oil-free fryer that works on hot air, Do not fill the pan with oil or frying fat.
Preparing for use
1 Place the appliance on a stable, horizontal and even surface.
Do not place the appliance on non-heart-resistant surface.
2 Place the basket in the pan (Fig.3).
3 Pull the cord from the storage compartment which locates on the bottom of the appliance.
Do not fill the pan with oil or any other liquid.
Do not put anything on top of the appliance, the airflow will be disrupted and affects
the air frying result.
Using the appliance
The oil-free can prepare a large range of ingredients. The recipe booklet included helps you
get to know the appliance.

Air frying
1. Connect the mains plug into an earthed wall socket.
2. Carefully pull the pan out of the Air fryer (Fig.4)
3. Put the ingredients in the basket. (Fig.5)
4. Slide the pan back into the Air fryer (Fig 6)
Noting to carefully align with the guides in the body of the fryer.
Never use the pan without the basket in it.
Caution: Do not touch the pan during and some time after use, as it gets very hot.
Only hold the pan by the handle.
5.Determine the required preparation time for the ingredient ( see section ‘Settings’ in this
chapter).
6.Some ingredients require shaking halfway through the preparation time (see section
“Settings” in this chapter). To shake the ingredients, pull the pan out of the appliance by
the handle and shake it. Then slide the pan back into the Air fryer
caution: Do not press the button of the handle during shaking. (Fig.3)
Tip: To reduce the weight, you can remove the basket from the pan and shake the basket
only. To do so, pull the pan out of the appliance, place it on a heat-resistant surface and
press the button of handle. and lift the basket out of the pan
Tip: If you set the timer to half the preparation time, you hear the timer bell when you have
to shake the ingredients. However, this means that you have to set the timer again to the
remaining preparation time after shaking.
7. When you hear the timer bell, the set preparation time has elapsed. Pull the pan out of the
appliance and place it on a trial framework.
Note: You can also switch off the appliance manually. To do this, press the “power on/off”
key.
8. Check if the ingredients are ready.
If the ingredients are not ready yet, simply slide the pan back into the appliance and set the
timer to a few extra minutes.
9. To remove ingredients (e.g. fries), pull the pan out of the Air fryer and place it on a trial
framework, and press the basket release button and lift the basket out of the pan.
Do not turn the basket upside down with the pan still attached to it, as any excess
oil that has collected on the bottom of the pan will leak onto the ingredients.
the pan and the ingredients are hot and hot fryer. Depending on the type of the
ingredients in the fryer, steam may escape from the pan.
10. Empty the basket into a bowl or onto a plate.
Tip: To remove large or fragile ingredients, lift the ingredients out of the basket by a pair of
tongs
11. When a batch of ingredients is ready, the Air fryer is instantly ready for preparing another
batch.

Control panel instructions
Operation Instructions:
NOTE: Make sure all the packaging materials are removed before adding food. The
frozen food need to be defrosted. And please immediately cook the food which has been
defrosted.
French fries
1. Connect the appliance with power source. One beep can be heard and all the
indicators on the control panel illuminate. Press Menu button “ ” to select the “French
fries” “ ”, and the default temperature and time of “French fries” setting are 200℃
and 20 minutes separately, which are indicated in the display. And you can adjust your
desired temperature and time by following the operation specified in the section of
“SET THE TEMPERATURE AND TIME MANUALLY”, and the display will
indicate the new temperature and time.
NOTE: The appliance will enter into the standby mode if there is not any operation
within 10 minutes after the appliance is powered on. At that time, only the Power button
“ ” and its corresponding indicator are activated while other buttons and their
Timer/temp
“+“Button
Timer/temp “-“key
Temp/timer toggle Button
START/PAUSE
key Button
Timer
Temperature
Recipes
Menu
Power Button

corresponding indicator are deactivated. And you can press the Power button “ ” to
activate all the functional buttons and indicators.
2. Put the wire rack into the frying tank and then add 500g frozen French fries on the
wire rack.
3. Install the frying tank well in position and then press the Start/Stop button “ ”,
then the appliance starts to work.
NOTE: During working, press the Start/Stop button “ ”, its corresponding indicator
flashes and the appliance will pause working. Press the Start/Stop button “ ” again,
the appliance will continue to work. To make the appliance stop working, hold and
press the Start/Stop button “ ”.
4. When the appliance finishes working, five beeps can be heard, and the food are fried
well.
Chop
1. Connect the appliance with power source. One beep can be heard and all the
indicators on the control panel illuminate. Press Menu button “ ” to select the “Chop”
“ ”, and the default temperature and time of “Chop” setting are 200℃and 15
minutes separately, which are indicated in the display. And you can adjust your desired
temperature and time by following the operation specified in the section of “SET THE
TEMPERATURE AND TIME MANUALLY”, and the display will indicate the new
temperature and time.
NOTE: The appliance will enter into the standby mode if there is not any operation
within 10 minutes after the appliance is powered on. At that time, only the Power button
“ ” and its corresponding indicator are activated while other buttons and their
corresponding indicator are deactivated. And you can press the Power button “ ” to
activate all the functional buttons and indicators.
2. Put the wire rack into the frying tank and then evenly add a layer of chops on the
wire rack.
3. Install the frying tank well in position and then press the Start/Stop button “ ”,
then the appliance starts to work.
NOTE: During working, press the Start/Stop button “ ”, its corresponding indicator
flashes and the appliance will pause working. Press the Start/Stop button “ ” again,
the appliance will continue to work. To make the appliance stop working, hold and
press the Start/Stop button “ ”.
4. When the appliance finishes working, five beeps can be heard, and the food are fried

well.
Bake
1. Connect the appliance with power source. One beep can be heard and all the
indicators on the control panel illuminate. Press Menu button “ ” to select the “Bake”
“ ”, and the default temperature and time of “Bake” setting are 180℃and 30
minutes separately, which are indicated in the display. And you can adjust your desired
temperature and time by following the operation specified in the section of “SET THE
TEMPERATURE AND TIME MANUALLY”, and the display will indicate the new
temperature and time.
NOTE: The appliance will enter into the standby mode if there is not any operation
within 10 minutes after the appliance is powered on. At that time, only the Power button
“ ” and its corresponding indicator are activated while other buttons and their
corresponding indicator are deactivated. And you can press the Power button “ ” to
activate all the functional buttons and indicators.
2. Put the wire rack into the frying tank and then add appropriate amount of food on the
wire rack.
3. Install the frying tank well in position and then press the Start/Stop button “ ”,
then the appliance starts to work.
NOTE: During working, press the Start/Stop button “ ”, its corresponding indicator
flashes and the appliance will pause working. Press the Start/Stop button “ ” again,
the appliance will continue to work. To make the appliance stop working, hold and
press the Start/Stop button “ ”.
4. When the appliance finishes working, five beeps can be heard, and the food are fried
well.
Chicken leg, chicken wing
1. Connect the appliance with power source. One beep can be heard and all the
indicators on the control panel illuminate. Press Menu button “ ” to select the
“Chicken leg, chicken wing” “ ”, and the default temperature and time of “Chicken
leg, chicken wing” setting are 200℃and 20 minutes separately, which are indicated in
the display. And you can adjust your desired temperature and time by following the
operation specified in the section of “SET THE TEMPERATURE AND TIME
MANUALLY”, and the display will indicate the new temperature and time.
NOTE: The appliance will enter into the standby mode if there is not any operation
within 10 minutes after the appliance is powered on. At that time, only the Power button

“ ” and its corresponding indicator are activated while other buttons and their
corresponding indicator are deactivated. And you can press the Power button “ ” to
activate all the functional buttons and indicators.
2. Put the wire rack into the frying tank and then evenly add a layer of chicken legs or
chicken wings on the wire rack.
3. Install the frying tank well in position and then press the Start/Stop button “ ”,
then the appliance starts to work.
NOTE: During working, press the Start/Stop button “ ”, its corresponding indicator
flashes and the appliance will pause working. Press the Start/Stop button “ ” again,
the appliance will continue to work. To make the appliance stop working, hold and
press the Start/Stop button “ ”.
4. When the appliance finishes working, five beeps can be heard, and the food are fried
well.
NOTES:
(1) Please pay attention to the food to avoid it being scorched during working process,
and it is necessary apply some seasonings on the food at the end of the work.
(2) Be careful when removing food after the food is cooked well. Use special gloves to
prevent being burnt.
Fish
1. Connect the appliance with power source. One beep can be heard and all the
indicators on the control panel illuminate. Press Menu button “ ” to select the “Fish”
“ ”, and the default temperature and time of “Fish” setting are 200℃and 12
minutes separately, which are indicated in the display. And you can adjust your desired
temperature and time by following the operation specified in the section of “SET THE
TEMPERATURE AND TIME MANUALLY”, and the display will indicate the new
temperature and time.
NOTE: The appliance will enter into the standby mode if there is not any operation
within 10 minutes after the appliance is powered on. At that time, only the Power button
“ ” and its corresponding indicator are activated while other buttons and their
corresponding indicator are deactivated. And you can press the Power button “ ” to
activate all the functional buttons and indicators.
2. Put the wire rack into the frying tank and then evenly add a layer of fishes on the
wire rack.
3. Install the frying tank well in position and then press the Start/Stop button “ ”,

then the appliance starts to work.
NOTE: During working, press the Start/Stop button “ ”, its corresponding indicator
flashes and the appliance will pause working. Press the Start/Stop button “ ” again,
the appliance will continue to work. To make the appliance stop working, hold and
press the Start/Stop button “ ”.
4. When the appliance finishes working, five beeps can be heard, and the food are fried
well.
Beefsteak
1. Connect the appliance with power source. One beep can be heard and all the
indicators on the control panel illuminate. Press Menu button “ ” to select the
“Beefsteak” “ ”, and the default temperature and time of “Beefsteak” setting are
200℃and 25 minutes separately, which are indicated in the display. And you can
adjust your desired temperature and time by following the operation specified in the
section of “SET THE TEMPERATURE AND TIME MANUALLY”, and the display
will indicate the new temperature and time.
NOTE: The appliance will enter into the standby mode if there is not any operation
within 10 minutes after the appliance is powered on. At that time, only the Power button
“ ” and its corresponding indicator are activated while other buttons and their
corresponding indicator are deactivated. And you can press the Power button “ ” to
activate all the functional buttons and indicators.
2. Put the wire rack into the frying tank and then evenly add a layer of beefsteaks on
the wire rack.
3. Install the frying tank well in position and then press the Start/Stop button “ ”,
then the appliance starts to work.
NOTE: During working, press the Start/Stop button “ ”, its corresponding indicator
flashes and the appliance will pause working. Press the Start/Stop button “ ” again,
the appliance will continue to work. To make the appliance stop working, hold and
press the Start/Stop button “ ”.
4. When the appliance finishes working, five beeps can be heard, and the food are fried
well.
Dry fruit
1. Connect the appliance with power source. One beep can be heard and all the
indicators on the control panel illuminate. Press Menu button “ ” to select the “Dry
fruit” “ ”, and the default temperature and time of “Dry fruit” setting are 30℃and 4

hours separately, which are indicated in the display. And you can adjust your desired
temperature and time by following the operation specified in the section of “SET THE
TEMPERATURE AND TIME MANUALLY”, and the display will indicate the new
temperature and time.
NOTE: The appliance will enter into the standby mode if there is not any operation
within 10 minutes after the appliance is powered on. At that time, only the Power button
“ ” and its corresponding indicator are activated while other buttons and their
corresponding indicator are deactivated. And you can press the Power button “ ” to
activate all the functional buttons and indicators.
2. Put the wire rack into the frying tank and then evenly add a layer of fruits which
have been cut well and are of uniform thickness on the wire rack.
3. Install the frying tank well in position and then press the Start/Stop button “ ”,
then the appliance starts to work.
NOTE: During working, press the Start/Stop button “ ”, its corresponding indicator
flashes and the appliance will pause working. Press the Start/Stop button “ ” again,
the appliance will continue to work. To make the appliance stop working, hold and
press the Start/Stop button “ ”.
4. When the appliance finishes working, five beeps can be heard, and the food are fried
well.
Shrimp
1. Connect the appliance with power source. One beep can be heard and all the
indicators on the control panel illuminate. Press Menu button “ ” to select the
“Shrimp” “ ”, and the default temperature and time of “Shrimp” setting are 180℃
and 12 minutes separately, which are indicated in the display. And you can adjust your
desired temperature and time by following the operation specified in the section of
“SET THE TEMPERATURE AND TIME MANUALLY”, and the display will
indicate the new temperature and time.
NOTE: The appliance will enter into the standby mode if there is not any operation
within 10 minutes after the appliance is powered on. At that time, only the Power button
“ ” and its corresponding indicator are activated while other buttons and their
corresponding indicator are deactivated. And you can press the Power button “ ” to
activate all the functional buttons and indicators.
2. Put the wire rack into the frying tank and then evenly add a layer of shrimps on the
wire rack.

3. Install the frying tank well in position and then press the Start/Stop button “ ”,
then the appliance starts to work.
NOTE: During working, press the Start/Stop button “ ”, its corresponding indicator
flashes and the appliance will pause working. Press the Start/Stop button “ ” again,
the appliance will continue to work. To make the appliance stop working, hold and
press the Start/Stop button “ ”.
4. When the appliance finishes working, five beeps can be heard, and the food are fried
well.
SET THE TEMPERATURE AND TIME MANUALLY
Connect the appliance with power source, press the Menu button “ ” to select your
desired menu, and its corresponding indicator flashes, then press Temperature/Time
button “ ” to set the temperature and time. When the display indicates “ ”,
press “ ” or “ ” to adjust the temperature. After finish setting temperature, press
Temperature/Time button “ ” again to enter into the time-setting mode. When the
display indicates “ ” , press “ ” or “ ” to adjust the time. After finish setting
time, press the Start/Stop button “ ” and the appliance starts working according to the
selected menu with new temperature and time.
Settings
This table below will help you to select the basic settings for the ingredients.
Note: Keep in mind that these settings are indications. As ingredients differ in origin, size,
shape as well as brand, we cannot guarantee the best setting for your ingredients.
Because the Rapid Air technology instantly reheats the air inside the appliance,pull the pan
briefly out of the appliance during air frying to disturb the process.
Tips
-Smaller ingredients usually require a slightly shorter preparation time than larger
ingredients.
-A larger amount of ingredients only requires a slightly longer preparation time, a smaller
amount of ingredients only requires a slightly shorter preparation time.
-Shaking smaller ingredients halfway through the preparation time optimizes the end result
and can help prevent unevenly fried ingredients.
-Add some oil to fresh potatoes for a crispy result. Fry your ingredients in the Air fryer

within a few minutes after you added the oil.
-Do not prepare extremely greasy ingredients such as sausages in the Air fryer .
-Snacks that can be prepared in a oven can also be prepared in the Air fryer
-The optimal amount for preparing crispy fries is 500 grams.
-Use pre-made dough to prepare filled snacks quickly and easily. Pre-made dough also
requires a shorter preparation time than home-made dough.
-Place a baking tin or oven dish in the Air fryer basket if you want to bake a cake or quiche
or if you want to fry fragile ingredients or filled ingredients
-You can also use the Air fryer to reheat ingredients. To reheat ingredients, set the
temperature to 150
℃
for up to 10 minutes.
Min-max
Amount
(g)
Time
(min.)
Temp
(/℃)
Shake Extra information
Potato & fries
Thin frozen fries 300-400 18-25 200 Yes
Thick frozen fries 300-400 20-25 200 Yes
Potato gratin 500 20-25 200 Yes
Meat & Poultry
Steak 100-500 10-20 180 No
Pork chops 100-500 10-20 180 No
Hamburger 100-500 10-20 180 No
Sausage roll 100-500 13-15 200 No
Drumsticks 100-500 25-30 180 No
Chicken breast 100-500 15-20 180 No
Snacks
Spring rolls 100-400 8-10 200 Yes
Use oven-ready
Frozen chicken nuggets 100-500 10-15 200 Yes
Frozen fish fingers 100-400 6-10 200 No
Frozen bread crumbed
cheese snacks 100-400 8-10 180 No
Stuffed vegetables 100-400 10 160 No
Baking
Cake 300 20-25 160 No Use additional baking
tin
Quiche 400 20-22 180 No
Muffins 300 15-18 200 No Use additional baking
tin/oven dish
Sweet snacks 400 20 160 No
Note: Add 5 minutes to the preparation time when you start frying while the Air fryer is still
cold.
Cleaning
Clean the appliance after every use.
The pan and the non-stick coating basket. Do not use metal kitchen utensils or

abrasive cleaning materials to clean them, as this may damage the non-stick coating.
1 Remove the mains plug from the wall socket and let the appliance cool down.
Note: Remove the pan to let the Air fryer cool down more quickly.
2 Wipe the outside of the appliance with a moist cloth.
3 Clean the pan, separator and basket with hot water, some washing-up liquid and a
non-abrasive sponge.
You can use degreasing liquid to remove any remaining dirt.
Note: The pan and basket are dishwasher-proof.
Tip: If dirt is stuck to the basket or the bottom of the pan, fill the pan with hot water with
some washing-up liquid. Put the basket in the pan and let the pan and the basket soak for
approximately 10 minutes.
4 Clean the inside of the appliance with hot water and non-abrasive sponge.
5 Clean the heating element with a cleaning brush to remove any food residues.
Storage
1 Unplug the appliance and let it cool down.
2 Make sure all parts are clean and dry.
Environment
Do not throw away the appliance with the normal household waste when it is exhausted,, but
hand it to an official collection point for recycling. By doing this, you help to preserve the
environment
Guarantee and service
If you need service or information or if you have a problem, please contact your local
authorized service centre
Troubleshooting
problem Possible cause Solution
The Air fryer does
not work
The appliance is not
plugged in.
Put the mains plug in an earthed wall socket.
You have not set the
timer.
Set the time to the required preparation time to
switch on the appliance.
The ingredients
fried with the air
fryer are not done.
The amount of
ingredients in the basket
is too big.
Put smaller batches of ingredients in the basket.
Smaller batches are fried more evenly.
The set temperature is
too low.
Set the temperature to the required temperature
setting (see section ‘settings’ in chapter ‘Using the
appliance’).
The preparation time is
too short.
Set the time to the required preparation time (see
section ‘Settings’ in chapter’ Using the appliance’).
The ingredients
are fried unevenly
in the air fryer.
Certain types of
ingredients need to be
shaken halfway through
the preparation time.
Ingredients that lie on top of or across each other
(e.g. fries) need to be shaken halfway through the
preparation time. See section ‘Settings’ in chapter
‘Using the appliance’.
Fried snacks are You used a type of Use oven snacks or lightly brush some oil onto the

not crispy when
they come out of
the air fryer.
snacks meant to be
prepared in a traditional
deep fryer.
snacks for a crispier result.
I cannot slide the
pan into the
appliance properly.
There are too much
ingredients in the
basket.
Do not fill the basket beyond the MAX indication.
The basket is not placed
in the pan correctly.
Push the basket down into the pan until you hear a
click.
White smoke
comes out of the
appliance.
You are preparing
greasy ingredients.
When you fry greasy ingredients in the air fryer, a
large amount of oil will leak into the pan. The oil
produces white smoke and the pan may heat up
more than usual. This does not affect the appliance
or the end result.
The pan still contains
grease residues from
previous use.
White smoke is caused by grease heating up in the
pan . make sure you clean the pan properly after
each use.
Fresh fries are
fried unevenly in
the air fryer.
You did not use the right
potato type.
Use fresh potatoes and make sure they stay firm
during frying.
You did not rinse the
potato sticks properly
before you fried them.
Rinse the potato sticks properly to remove starch
from the outside of the sticks.
Fresh fries are not
crispy when they
come out of the air
fryer.
The crispiness of the
fries depends on the
amount of oil and water
in the fries.
Make sure you dry the potato sticks properly before
you add the oil.
Cut the potato sticks smaller for a crispier result.
Add slightly more oil for a crispier result.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmental safe
recycling.