Rane ZONE POWER LIGHT User manual
2
3
User Guide (English)
Introduction
Thank you for purchasing the Zone Power Eight. At Rane, performance and reliability mean as
much to us as they do to you. That’s why we design our equipment with only one thing in
mind—to make your performance the best it can be.
Box Contents
Zone Power Eight
(8) 5 mm, 3-pin Euroblock connectors
(8) 5 mm, 2-pin Euroblock connectors
Power Cable
User Guide
Safety & Warranty Manual
Support
For the latest information about this product (documentation, technical specifications, system
requirements, compatibility information, etc.) and product registration, visit
ranecommercial.com.
For additional product support, visit ranecommercial.com/support.
4
Features
Front Panel
1
2
3
1. Power Light: This light will turn on when Zone Power Eight is powered on.
2. Signal/Clip/Protection LEDs: Each column of three LEDs shows the signal status of the
corresponding Channel Input (labeled on the front panel as CH1-8):
• Clip LED (CLIP): When the Clip LED is lit red, the input’s signal is “peaking” (higher than
0 dB). To prevent the “clipping” (distortion) that can result from a loud input signal, turn
the input’s volume knob (on the rear panel) counter-clockwise or reduce the volume on
the device plugged into the input.
• Signal LED (SIG): The Signal LED will be lit green when the signal coming from the
input is at an optimal volume level.
• Protection LED (PROT): If the Protection LED turns red, Zone Power Eight is in heat
protection mode and will not output sound. To restore sound output, reduce Zone Power
Eight’s temperature by making sure there is good ventilation and/or decreasing the input
volume.
3. Air Intake Vents: Keep these vents clear from obstructions to allow air to flow through the
front grill for proper performance.
Rear Panel
1
2
3
4
5 6
1. Power Input: Use the included power cable to connect this input to a power outlet.
2. Fuse: If the unit’s fuse is broken, lift this tab to replace the fuse. Replace it with a fuse with
an appropriate rating. Using a fuse with an incorrect rating can damage the unit and/or fuse.
3. Exhaust Vents:Air from the front intake flows through the unit and exits here. For proper
performance, do not block the air vents.
4. Channel Inputs with Volume Knobs (Input 1-8): Use Euroblock connectors to connect
these inputs to your audio sources. Each channel has a volume knob that you can use to
raise or lower the signal coming from your audio source. See Setup for more instructions.
5. Channel Outputs (CH1-8): Use Euroblock connectors to connect these outputs to your
loudspeakers. Each output sends the amplified signal from the corresponding Channel
Input to the connected loudspeaker. See Setup for more instructions.
Note: Use only 70V/100V speakers designed with step-down transformers. Using low
impedance 4Ω/8Ωspeakers on 70V/100V outputs will overload and possibly damage this
amplifier.
6. Operation Mode Switches:To set a Channel Output’s operation mode in accord with
the speaker connected to it, adjust the corresponding switch (1-8) to 70V or 100V.
5
Setup
1. Use the included 3-pin Euroblock connectors to connect the Channel Inputs on the rear
panel to your audio sources. Each input has a ground (G), cold/negative (–), and
hot/positive (+) connector. See below for further instructions on the Euroblock connector.
2. Use the included 2-pin Euroblock connectors to connect the Channel Outputs on the rear
panel to your loudspeakers. Each output has a cold/negative (–) and hot/positive (+)
connector. See below for further instructions on the Euroblock connector.
3. Use the included power cable to connect the Power Input to a power outlet.
4. Power on all of your audio sources and Zone Power Eight.
5. Begin playing your audio sources. Adjust the volume knob for each Channel Input as
necessary.
Using the Euroblock Connector:
1. Use a small screwdriver to loosen the screws corresponding to the insert ports on the
Euroblock connector.
2. Twist the speaker wire to form a tight strand and insert it into the appropriate insert port
(following the +, -,and Glabels on the rear panel of Zone Power Eight). Push the wire until
it is secured inside. Repeat this step for each port.
3. Tighten the screws corresponding to the insert ports on the Euroblock connector.
4. Insert the Euroblock connector into the desired Channel Input or Channel Output on
Zone Power Eight.
If you would like to disconnect a wire, first make sure you loosen the corresponding screw
on the Euroblock connector before you pull out the wire.
Channel 1 Output
Euroblock
Connector
Screws
Insert Ports
Speaker Wire
Euroblock
Connector
Channel 1 Input
Screws
Insert Ports
Speaker Wire
6
Connection Diagram
Items not listed under Introduction >Box Contents are sold separately.
ZONE2
SOURCE ZONE 3 ZONE3
SOURCE STATUS DIMMER
VIDEO
AUX1
SETUPMI C
INTE GR ATE D NE TWO RK AVRECE IV E R
L- AUDIO - R
1CBL/SAT 3 G A ME 4 NET WOR K
QUICK S EL ECT
2Blu-ray
PHONES BACK
ENTER
INFO
SETUP
ZONE2
SOURCESELECT
MASTERVOLUME
ON/OFF
AUX1
HDMI7 5 V/1A
ON/OFF OPTION
Troubleshooting
If you encounter a problem, first try one or more of the following:
• Make sure all cables and other connected devices are properly and securely connected.
• Make sure you are using Zone Power Eight as described in this user guide.
• Make sure your other devices are working properly.
• If you believe Zone Power Eight is not working properly, check the following table for your
problem and solution.
Problem: Solution:
Power does not turn on. Make sure the Power Input is properly
connected to a power outlet using the included
power cable.
Zone Power Eight does not produce any
sound, or the sound is distorted.
Make sure all cable and device connections are
secure and correct.
Make sure none of the cables are damaged.
Make sure the volume settings on your
loudspeaker, mixer, etc. are correct.
The sound has a hum or noise. Check the polarity of the input connections.
If an unbalanced connection is used, ensure
the terminal (-) is linked to GND.
If the clip LED is lit, reduce the volume.
Check the polarity of the speaker connections.
Multimedia Playe
r
Loudspeakers
Receive
r
Powe
r
23
Appendix (English)
Technical Specifications
Connectors (8) Euroblock inputs
(8) Euroblock outputs
(1) IEC power cable input
Total Harmonic Distortion < 0.1%
Frequency Response 100 Hz–15 kHz (0 ±3 dB)
Signal-to-Noise Ratio > 95 dB
Channel Separation > 70 dB
Input Sensitivity 0.9–1.1 V (0 ±1 dBv)
Input Impedance 20k Ωbalanced or 10k Ωunbalanced
Damping Factor > 200 (1k 8 Ω)
Voltage Gain 40 (±1 dB @ 100 V)
Power Via power cable
Connection: IEC
Voltage: 110–120 V or 220–240 V, 50/60 Hz
Consumption: 1200 W (150 W per channel)
Dimensions
(width x depth x height)
19” x 14.2” x 1.7”
48.3 x 36.1 x 4.3 cm
Weight 15.4 lb.
7 kg
Specifications are subject to change without notice.
Trademarks & Licenses
Rane is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. All other product
names, company names, trademarks, or trade names are those of their respective owners.
l,lANE)
Important
Safety
Instructions
&
Warranty
Information
English (3 - 7 )
lnstrucciones
importantes
de
seguridad
e
informaci6n
de
la
garantia
Espanol (8 -
11
)
Instructions
importantes
de
securite
et
informations
de
garantie
Fran9ais ( 12
-15)
lstruzioni
importanti
di
sicurezza
e
le
informazioni
della
garanzia
Italiano ( 16 -19)
Wichtige
Sicherheitsanweisungen
und
Garantieinformationen
Deutsch (20 -
23)
Rane
is
a trademark
of
inMusic Brands, Inc., registered
in
the U.S. and othercountries.
NEMA
"'
is the registered trademark and service mark
of
the National Electrical ManufacturersAssociation.
All otherproduct names, company names, trademarks, ortrade names are those
of
their respective owners.
2
RANE]
1.
What is covered and for how long?
Product Warranty
(for products purchased in the U.S.A.)
All
F'roducts: inMusic Brands, Inc. ("inMusic") warrants
to
the original purchaser that Rane products and all other
. accessories are free from defects in material and workmanslhip under normal use and service for the period commencing
upon the date of purchase from
an
authorized Rane dealer and continuing for the following peri
od
of time after that date
for one
(1)
year. inMusic warrants factory-refurbished merchandise
to
be free of material and operational defects for a
period
of
ninety (90) days from the original date
of
retail sale. This refurbished merchandise warranty is nottransferabl
e.
2. What
is
not covered? This Limited Warranty is conditioned upon proper use
of
the product
by
the purchaser. This
Limited Warranty does not cover:
(a)
damage caused
by
improper installation or improper connection
to
any peripheral;
(b)
damage caused
by
an
external electrical fault;
(c)
damage from use
of
parts
not
manufactured
or
sold
by
Rane; (d)
product purchased from anyone other than
an
Rane authorized dealer;
(e)
modifications
to
product not approved in
writing by Rane;
(f)
equipment that has the serial number removed or made illegible; (g) normal cosmetic and
mechanical wear;
(h)
damage
or
loss during transit
to
an
Authorized Rane Repair Center;
or
(i
) uni
ts
that are purchased
and/
or
located outside
of
the continental USA.
3. What are inMusic's obligations? During the applicable warranty period, Rane will repair
or
replace, at Rane's sole
option, without charge
to
the purchaser, any defective component part
of
the product. To obtain service under this
Limited Warranty, purchaser
must
first contact Rane and obtain a return merchant authorization ("RMA") number.
Purchaser must then return the product
to
Rane in an adequate container
for
shipping, accompanied by purchaser's
sales receipt
or
comparable proof
of
sale showing the
date
of
purchase, the serial number
of
the product, and the
seller's name and address. To obtain an RMA number and assistance on where
to
return the product, contact Rane
customer service
at
401-659-8192. Upon receipt, Rane will repair
or
replace the defective products. Rane may,
at
Rane's sole option, use rebuilt, reconditioned,
or
new parts
or
components when repairing any product
or
replace a
product with a rebuilt, reconditioned, new
or
comparable product. Repaired products will be warranted for a period
equal
to
the remainder
of
the original Limited Warranty on
the
original product
or
for 90 days, whichever
is
longer. All
replaced parts, components, boards, and equipment become the property
of
Rane. If Rane determines that any
product is
not
covered by this Limited Warranty, purchaser must pay all parts, shipping, and labor charges for the
repair or return
of
such product.
4. What are
the
limits on inMusic's liabilities? THE WARRANTIES
GIVEN
IN
THIS LIMITED WARRANTY, TOGETHER
WITH ANY IMPLIED WARRANTIES COVERING RANE PRODUCTS, INCLUDING WITHOUT LIMITATION ANY
WARRANTIES OF MERCHANTABILITY
OR
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED
BY
APPLICABLE LAW, INMUSIC
OR
RANE SHALL NOT BE LIABLE
FOR
ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT
OR
SIMILAR
DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER'S PROPERTY,
OR
INJURY TO PURCHASER OR
OTHERS ARISING OUT OF THE USE, MISUSE
OR
INABILITY TO USE ANY RANE PRODUCT, BREACH OF
WARRANTY,
OR
NEGLIGENCE, INCLUDING BUT NOT LIMITED TO INMUSIC'S OR RANE'S OWN NEGLIGENCE,
EVEN
IF
INMUSIC, RANE, OR THEIR AGENTS HAVE BEEN ADVISED OF SUCH DAMAGES,
OR
FOR ANY CLAIM
BROUGHT AGAINST PURCHASER
BY
ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE COMPLETE
WARRANTY
FOR
RANE PRODUCTS, AND
IS
GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND
STATES PURCHASER'S EXCLUSIVE REMEDY.
IF
ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR
UNENFORCEABLE BY REASON
OF
ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT
AFFECT THE ENFORCEABILITY OF THE REMAINDER
OF
THIS LIMITED WARRANTY WHICH PURCHASER
ACKNOWLEDGES IS AND WILL ALWAYS
BE
CONSTRUED TO BE LIMITED BY ITS TERMS
OR
AS LIMITED AS THE
LAW PERMITS.
This Limited Warranty allocates risk
of
productfailure between purchaser and Rane, and Rane's product pricing reflects
this allocation
of
risk and the limitations
of
liability contained
in
this Limited Warranty. The agents, employees,
distributors, and dealers
of
Rane are not authorized
to
make modifications
to
this Limited Warranty,
or
make additional
warranties binding on Rane
or
inMusic. Accordingly, additional statements such as dealer advertising
or
presentation,
whether oral
or
written,
do
not constitute warranties by Rane
or
inMusic and should
not
be relied upon.
5.
How
does state
law
apply to this warranty? SOME STATES
DO
NOT ALLOW THE EXCLUSION OR LIMITATIONS OF
INCIDENTAL
OR
CONSEQUENTIAL DAMAGES OR HOW LONG
AN
IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS
OR
EXCLUSIONS MAY NOTAPPLY TO PURCHASER.
This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction
to
another.
Please record the serial number
of
your unit as shown on the back
of
the
chassis as well as the name
of
the dealer from
whom you purchased the unit. Retain this information and your original purchase receipt for your records. Go
to
our website
ranecommercial.com
to
register your product with us.
Model: Purchased From:
Serial Number: Date
of
Purchase:
3
RANE]
Product Warranty
(for
products
purchased
outside
of
the
U.S
.A.)
1.
inMusic Brands, Inc. ("inMusic") warrants
to
the original purchaser that Rane products are free from
defects in material and workmanship under normal use and service for the period commencing upon
the date
of
purchase from
an
authorized Rane dealer and continuing for the following period
of
time
after that date for
(1)
Year.
2. This Limited Warranty is conditioned upon proper use
of
the product bythe purchaser.
This Limited Warranty does not cover:
(a)
defects or damage resulting from accident, misuse, abuse,
neglect, unusual physical or electrical stress, modification
of
any part
of
the product, or cosmetic
damage;
(b)
equipment that has the serial number removed
or
made illegible;
(c)
all plastic surfaces and
other externally exposed parts that are scratched
or
damaged due
to
normal use;
(d)
defects
or
damage
from improper testing, operation, maintenance, installation, adjustment,
or
servi
ce
of
the products.
3. During the applicable warranty period, Rane will repair
or
replace,
at
Rane's sole discretion, without
charge
to
the purchaser, any defective component part
of
the product. Rane may, at Rane's sole
discretion, use rebuilt, reconditioned,
or
new parts
or
components when repairing any product
or
replace a product with a rebuilt, reconditioned, new
or
comparable product.
4. THE WARRANTIES GIVEN
IN
THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED
WARRANTIES COVERING RANE PRODUCTS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES
OF MERCHANTABILITY OR FITNESS
FOR
A PARTICULAR PURPOSE,
ARE
LIMITED TO THE
DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, INMUSIC OR RANE SHALL NOT BE LIABLE
FOR
ANY SPECIAL, INCIDENTAL,
CONSEQUENTIAL, INDIRECT
OR
SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO
PURCHASER'S PROPERTY,
OR
INJURY TO PURCHASER
OR
OTHERS ARISING OUT OF THE USE,
MISUSE OR INABILITY TO USE ANY RANE PRODUCT, BREACH OF WARRANTY, OR NEGLIGENCE,
INCLUDING BUT NOT LIMITED
TO
INMUSIC'S
OR
RANE'S OWN NEGLIGENCE,
EVEN
IF
INMUSIC,
RANE,
OR
ITS
AGENTS HAVE
BEEN
ADVISED OF SUCH DAMAGES,
OR
FOR
ANY CLAIM BROUGHT
AGAINST PURCHASER BY ANY OTHER PARTY. THIS LIMITED WARRANTY
IS
THE COMPLETE
WARRANTY
FOR
RANE'S PRODUCTS, AND IS
GIVEN
IN
LIEU
OF ALL OTHER EXPRESS
WARRANTIES. THIS LIMITED WARRANTY SHALL NOT
EXTEND
TO
ANYONE OTHER THAN THE
ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER'S EXCLUSIVE REMEDY.
IF
ANY PORTION OF THIS LIMITED WARRANTY
IS
ILLEGAL
OR
UNENFORCEABLE BY REASON OF
ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE
ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER
ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR
AS
LIMITED AS THE LAW PERMITS.
This Limited Warranty allocates risk
of
product failure between purchaser and Rane, and Rane's product
pricing reflects this allocation
of
risk and the limitations
of
liabili
ty
contained in this Limited Warranty. The
agents, employees, distributors, and dealers
of
Rane are not authorized to make modifications to this
Limited Warranty,
or
make additional warranties binding on Rane or inMusic. Accordingly, additional
statements such as dealer advertising or presentation, whether oral or written,
do
not constitute warranties
by Rane or inMusic and should
not
be
relied upon. Some jurisdictions
do
not allow limitations on how long
an
implied warranty lasts, so the above limitation may
not
apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary under local laws.
Please record the serial number
of
your unit as shown on the back
of
the chassis as well as the name
of
the
dealer from whom you purchased the unit. Retain this information and your original purchase receipt
for
your records. Go to our website ranecommercial.com
to
register your product with us.
Model: Purchased From:
Serial Number:
Date
of
Purchase:
4
Return Information
• A return merchant authorization number must
be
obtained from your local Rane representative. For your representative go
to
ranecommercial.com.
• A
copy
of
the original sales receipt must also be included
for
the equipment
to
be repaired under warranty.
• The faulty equipment must be packed in its original packaging.
• One additional outer layer
of
packaging must be included
to
ensure product safety. Failure
to
do
so
may inadequately protect the
equipment in transit and therefore jeopardize the warranty.
• Rane will
not
accept COD shipments and no call tags will
be
issued
for
merchandise return.
• Rane will not return repaired merchandise
to
customers by priority service except
by
written request
at
the customer's cost.
Requests must be submitted
in
writing with returned merchandise.
• The defective Rane equipment should be sent freight prepaid with the return merchant authorization number printed clearly on the
outer packaging and original sales receipt enclosed
to
your local service center.
Very Important
Please read this section before connecting this unit
to
yoursystem:
For optimum performance:
• All slide faders are subject
to
wear. Excessive force can wear out
the
faders quickly. User-replaceable slide faders are not covered
by
our
warranty.
• Never use spray cleaners on the slide controls. Residues cause excessive dirt build-up and this will void your warranty. In normal
use, slide controls can last for many years. If they malfunction (usually because
of
a dirty
or
dusty environment), consult a
professional technician.
• Always make sure thatAC power is
off
while making any connections.
• Use appropriate cables throughout your system. Do not use excessively long cables
(i.e.
over32 feet / 10 meters). Be sure plugs and
jacks are tightly mated. Loose connections can cause hum, noise,
or
intermittents that could easily damage your speakers. Make the
input and output connections with readily available low-capacitance stereo cables. Cable quality makes a big difference
in
audio
fidelity and "punch." See your Rane dealer
or
an
electronics
or
audio specialist store
if
you are not sure which cables
to
use.
• Never attempt
to
make any adjustments otherthan those described
in
this manual, or repairs. Take the unit
to
your dealer
or
to
an
authorized Rane service center.
• /iJways remember: tum amps
on
last and off first. Begin with masterfaders
or
volume controls
on
minimum and the amplifier gain/input
control(s) down. Wait 8-1Oseconds beforeturning
up
the volume. This preventstransientswhich maycause severe speakerdamage.
• Use restraint when operating controls. Try
to
move them slowly. Rapid adjustmentscould damage equipmentdue
to
amplifier clipping.
• Avoid amplifier "clipping"
at
all costs: this occurs when the red LEDs (usually on the front panel
of
most professional power
amplifiers) start flashing. "Clipping" is when the power amplifier is distorting and working beyond its limits. Amplifier distortion is
the main cause
of
speaker failure.
• To prevent fire
or
shock hazard,
do
not expose
the
unit
to
rain
or
moisture. Never place cans
of
beer, soda, glasses
of
water
or
anything
wet
near
or
on
top
of
the unit!
• Headphone outputs can
be
set
to
levels which can cause damage
to
your ears. Use caution.
• This unit may contain a microcomputer
for
signal processing and control functions. In very rare situations, severe interference,
noise from
an
external source,
or
static electricity maycause it
to
lock up. In
the
unlikely event
that
this should happen, turn
off
the
unit, wait at leastfive seconds, and then turn
it
back on again.
• Under rare circumstances,
if
this product is exposed
to
electromagnetic interference during use, there may be a slight
drop
in
signal-to-noise ratio.
• Intended electromagnetic environments: residential, commercial, light industrial, urban outdoors.
Important Safety Instructions
1. Read and keep these instructions. Heed all warnings and follow all Instructions.
2.
Do
not
use this apparatus near water (if applicable).
3.
Clean onlywith drycloth.
4.
Do
not block any ventilation openings (if applicable). Install in accordance with the manufacturer's instructions. Do
not
install this
equipment
in
a confined
or
"boxed-in" space such as a bookcase
or
similar unit, and maintain good ventilation conditions. The
ventilation should
not
be impeded
by
covering the ventilation openings with items such as newspaper, tablecloths, curtains, etc.
5.
Do not install near any heat sources such as radiators, heat registers, stoves,
or
otherapparatus (including amplifiers) that produce
heat. Do
not
placeexposed flame sources such as lighted candles on the apparatus.
6.
Do not defeat the safety purpose
of
the polarized
or
grounding-type plug (if applicable). A polarized plug has
two
blades with one
wider than the other. A grounding type plug has
two
blades and a third grounding prong. The wide blade
or
the third prong is
provided foryour safety. Ifthe provided plug does notfit into youroutlet, consult
an
electrician
for
replacement
of
the obsoleteoutlet.
7.
(If
applicable) Protect the power cord from being walked on
or
pinched particularly at plugs, convenience receptacles, and the
point where they exitfrom
the
apparatus.
~
8.
Only use attachment/accessories specified by the manufacturer.
~
9.
Use
only the cart, stand, tripod, bracket
or
table specified
by
the manufacturer,
or
sold with the apparatus
(if
applicable). •
'",
When acart is used, usecaution when moving the cart/apparatus combination
to
avoid injury from tip-over.
l•
10. Unplugthis apparatus during lightning storms
or
when unused
for
long periods
of
time.
~~
11. Refer all servicing
to
qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord
or
plug
is
damaged, liquid has been spilled
or
objects have fallen into the apparatus, the apparatus has been
exposed
to
rain
or
moisture, does
not
operate normally,
or
has been dropped.
12. Power Sources (if applicable): This product should be connected
to
a power supply only
of
the
type described in these operating
instructions,
or
as marked on the unit.
13. Internal/External Voltage Selectors (if applicable): Internal
or
external voltage selector switches,
if
any, should only
be
reset and re-
equipped with a properplug for alternative voltage
by
a qualified servicetechnician. Do not attempt
to
alterthisyourself.
5
14. Water and Moisture (if applicable): This product should
be
kept away from direct contact with liquids. The apparatus shall
not
be
exposed
to
dripping
or
splashing and that no objects filled with liquids, such as vases, shall
be
placed on the apparatus.
15. Caution (if applicable): Danger
of
explosion
if
battery is incorrectly replaced. Replace only with the same or equivalent type.
Batteries
(a
battery pack
or
an installed battery) shall not be exposes
to
excessive heat such as sunshine, fire, etc.
16. (If applicable) Where the mains plug
or
an appliance coupler is used as the disconnect device, the disconnect device shall remain
readily operable.
17. Protective earthing terminal (if applicable): The apparatus should be connected
to
a mains socket outlet with a protective
l'.:D
earthing connection. ©
• Denmark
(Danmark):
Apparatets stikprop skal tilsluttes en stikkontakt medjord, som giverforbindelse til stikproppensjord.
• Finland (Suom,): Laite on liitettava suojakoskettimilla varustettuun pistorasiaan.
• Norway (Norge): Apparatet mA tilkoples jordet stikkontakt.
• Sweden (Sverige): Apparaten skall anslutastill jordat uttag.
[g]
18. For Class II apparatus only: This symbol means the equipment is a Class
II
or
double-insulated electrical appliance. It D
has been designed in such a way that
it
does
not
require a safety connection
to
electrical earth.
19. Class II Wiring (if applicable): To reduce the risk
of
electric shock, the external wiring connected
to
the terminals with "Class
II
Wiring" requires Class
II
wiring installed by an instructed person
or
the
use
of
ready-made leads
or
cords.
20. Warning (if applicable): Provide an earthing connection before
the
mains plug is connected
to
the mains. When disconnecting the
earthing connection, be sure
to
disconnect
it
after pulling the mains plug
out
from
the
mains.
21. This apparatus is for professional use only. Intended operational climate: moderate.
22. (If applicable) When moving
or
not
using
the
appliance, secure the
power
cord
(e.g., wrap it with a cable tie). Be careful not
to
damage the power cord. Before using
it
again, make sure the power cord has
not
been damaged. If the power cord has been
damaged at all, bring the unit and
cord
to
a qualified service technician for repair
or
replacement as specified
by
the manufacturer.
23. Warning (if applicable): To prevent possible hearing damage,
do
not
listen
at
high volume levels for long periods.
~
24. Warning (if applicable): Please refer
to
any important information (e.g., electrical, safety, etc.) printed on the exterior
~
bottom enclosure
or
rear panel before installing
or
operating the product.
t,
25. Warning (if applicable): Terminals marked with the lightning bolt symbol may be
of
sufficient magnitude
to
constitute a risk
of
electric shock.
Service Instructions
• Disconnect power cord before servicing.
• Replace critical components.&only with factory parts
or
recommended equivalents.
• For AC line powered units: Before returning repaired unit
to
user, use an ohmmeter
to
measure from both AC plug blades
to
all
exposed metal parts. The resistance should
be
more than 2,000,000 ohms.
Safety Notices
NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE I R
isk
of
el
ec
t
ric
s
ho
ck.
Z
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY COVER. ~ · '
~
PERSONNEL ONLY.
■
.,__o_
o
_n_
ot
_o_p_e
_n_
. _
_.
7
DANGEROUS VO
LT
AG
E:
The lightning flash with arrowhead symbol within the equilateral triangle is intended
to
alert the
~
user
to
the presence
of
un-insulated "dangerous voltage" within the product's enclosurethat may
be
of
sufficient magnitude
~
to
constitute a risk
of
electric shock.
SA
1955
INSTRUCTIONS: The exclamation point within the equilateral triangle
is
intended
to
alert the user
to
the presence
of
"'•
important operating and maintenance (servicing) instructions
in
the literature accompanying this appliance.
~
SA
1966
WARNING:
To
reduce the risk
of
fire
or
electrical shock,
do
not expose this appliance
to
rain
or
moisture. Electrical equipment should
NEVER
be
kept
or
stored
in
damp environments.
CAUTION
(f
or
U.SA
& CANADIAN models
on
ly):
TO
PREVENT
ELECTRIC
SHOCK
DO
NOT
USE
THIS
(POLARIZED)
PLUG
WITH
AN
EXTENSION
CORD,
RECEPTACLE
OR
OTHER
OUTLET UNLESSTHE
BLADES
CAN
BE
FULLY
INSERTED
TO
PREVENT
BLADE
EXPOSURE.
NOTICE CONCERNING LASER PRODUCTS: DANGER: INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR
DEFEATED. AVOID DIRECT EXPOSURE TO BEAM. USE OF CONTROLS
OR
ADJUSTMENTS OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT
IN
HAZARDOUS RADIATION EXPOSURE.
NOTICE CONCERNING FCC REGULATIONS: You are cautioned that changes
or
modifications not expressly approved by the part
responsible
for
compliance could void the user's authority
to
operate the equipment. This equipment has been tested and found
to
comply with the limits
for
a Class B digital device, pursuant
to
Part 15
of
the
FCC rules. These limits are designed
to
provide
reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and,
if
not installed and used in accordance with the instructions, may cause harmful interference
to
radio
communications. However, there is
no
guarantee that interference will
not
occur
in a particular installation.
If
this equipment does
cause harmful interference
to
radio
or
television reception, which can be determined
by
turning the equipment off and on, the user is
encouraged
to
try
to
correct the interference
by
one
or
more
of
the
following measures:
(a)
reorient
or
relocate the receiving antenna;
(b) move this unit; (c) increase the separation between the equipment and receiver; (d) connect the equipment into an outlet
on
a
circuit different from that
to
which the receiver
is
connected;
(e)
be sure that all cables are properly shielded, using a choke
or
ferrite
where appropriate;
or
(f)
consult the dealer
or
an experienced radio/television technician for help.
This device complies with Part
15
of
the FCC rules. Operation
is
subject
to
the
following
two
conditions: (1) this device
may
not
cause
harmful interference, and (2) this device
must
accept any interference received, including interference that may cause undesired
operation.
6
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits
set
forth
for
an uncontrolled
environment. Thisequipment should
be
installed and operated with a minimum distance
of
20
cm
between
the
radiator
and
your
body.
ForCanadian models:
• This device complies with Industry Canada licence-exempt RSSs. Operation
is
subject
to
the
following
two
conditions: (1) this
device
may
not
cause interference, and
(2)
this
device
must
accept any interference, including interference
that
may
cause
undesired operation
of
the
device.
• Under Industry Canada regulations, this radio transmitter
may
only operate using an antenna
of
a
type
and maximum (or lesser)
gain approved
for
the transmitter
by
Industry Canada.
To
reduce potential radio interference
to
other users,
the
antenna
type
and
its
gain should
be
so
chosen that
the
equivalent isotropically radiated
power
(e.i.r.p.) is
not
more
than
that
necessary
for
successful communication.
• This radio transmitter (identify the device
by
certification number,
or
model
number
if Category
II)
has been approved
by
Industry
Canada
to
operate with
the
antenna types listed
below
with
the
maximum penmissible gain
and
required antenna impedance
for
each antenna
type
indicated. Antenna types
not
included in
this
list, having a gain greater than
the
maximum gain indicated
for
that
type, are strictly prohibited
for
use with this device.
• This unit
does
not
exceed
the
Class B limits
for
radio noise emission
from
digital apparatus
set
out
in
the
radio interference
regulations
of
the
Canadian Department
of
Communications.
• This device operates on a no-protection, no-interference basis. Should
the
user seek
to
obtain protection
from
other radio
services operating in the same
TV
bands, a radio licence is required. For further details, consult Innovation, Science and
Economic Development Canada's
document
Client Procedures Circular CPC-2-1-28, Voluntary Licensing
of
Licence-Exempt
Low-PowerRadio Apparatus in
the
TV
Bands.
Wireless Microphone (if applicable): This device complies with Part 15
of
the FCC Rules. Operation is subject
to
the
condition
that
this device
does
not
cause harmful interference.
For wireless products supporting the 5G frequency band (if applicable): Usage
of
the
5.15-5.25
GHz
band are restricted
to
indoor
operation only. This applies
to
the following countries: AT, BE, BG, CZ, DK,
EE,
FR,
DE,
IS, IE, IT, EL,
ES,
CY, LV, LI, LT, LU, HU, MT,
NL, NO, PL, PT, RO, SI, SK, TR, Fl,
SE,
CH, UK, HR.
ESD/EFT Warning: This unit
may
contain a microcomputer
for
signal processing and control functions. In very rare situations,
severe interference, noise
from
an external source,
or
static electricity
may
cause
it
to
lock up. In the unlikely event
that
this
should happen, turn off the unit, wait
at
least five seconds, and then turn
it
back
on again. The pins
of
connectors identified
with this ESD warning symbol should
not
betouched.
RF Warning Statement: The device has been evaluated
to
meet general RF exposure requirement. The device can
be
used in
portable exposure condition without restriction.
For best audio quality, avoid using this device in a high RF-radiated environment. In an environment with radio frequency interference,
the unit
may
malfunction and resume normal operation after removal
of
the interference.
For 240-volt usein U.K., use NEMA•-style 240-volt plug. For othercountries use proper plug
for
local outlet.
Double-Insulated: When servicing use only identical replacement parts.
-Correct Disposal
of
This Product: This marking indicates
that
this
product
should
not
be
disposed with other household
wastes throughout the
EU.
To
prevent possible harm
to
the
environment
or
human health from uncontrolled waste disposal,
recycle it responsibly
to
promote
the
sustainable reuse
of
material resources.
To
return
your
used device, please use
the
return and collection systems
or
contact
the
retailer where
the
product
was purchased. They can take
this
product
for
environmentally safe recycling.
If
apparatus
contains
a
coin/button-cell
battery:
Warning:
Do
not
ingest
the
battery-chemical
burn
hazard.
The
remote control supplied with this
product
contains a coin/button-cell battery. If
the
coin/button-cell battery is swallowed, it
can cause severe internal burns in
just
2 hours and can lead
to
death. Keep
new
and
used batteries away
from
children. If
the battery compartment
does
not
close securely,
stop
using
the
product
and
keep
it
away from children.
If
you think
batteries
might
have been swallowed
or
placed inside any part
of
the
body, seek immediate medical attention.
Disposal
of
Batteries (if applicable):
• Neverdispose
of
anytypes
of
batteries in fire
or
nearexcessive heat
or
direct sunlight. Overheated batteries can rupture
or
explode.
•
If
you are unsure
of
how
or
where
to
dispose
of
a battery, refer
to
your local ordinances for
the
proper location, method, etc.
• Alkaline batteries & lithium button cell batteries: You can safely dispose
of
alkaline
and
lithium button cell batteries with
normal household waste. They
do
not
pose
a health
or
environmental risk during normal use
or
disposal. (Alkaline batteries are
composed primarily
of
common metals like steel, zinc, and manganese.)
Do
notdispose
of
large amounts
of
alkaline
or
lithium button cell batteries in a group. Used batteriesare often
not
completely "dead."
Grouping them togethercan bring these "live" batteries intocontact with one another, creating safety risks. To avoidthis, insulateeach
battery with tape
or
other non-conductive material
to
ensure it does
not
discharge. Proven cost-effective and environmentally safe
recycling processes are
not
yet universally available for alkaline and lithium button cell batteries. Some communities offer recycling or
collection
of
these batteries. Formoreinfonmation, referto your local ordinances orcontact yourlocal government.
• Lead-acid batteries: Dispose
of
lead-acid batteries
by
bringing them
to
an electronic waste center
or
recycling center,
or
dispose
of
them in accordance with
your
local ordinances. (Rechargeable lead-acid batteries are the same
type
used in
automobiles
and
should be disposed
of
in a similarfashion.)
General Note on the Declaration of Conformity: We hereby declare that this device is in accordance
with the essential requirements
of
the
European Directive 2014/53/EU
or
2014/30/EU (LVD: 2014/35/EU;
GPSD: 2001/95/EC). Thefull EU declaration
of
confonmity can
be
requested
at
the
address shown here
or
at
ranecommercial.com/safety
7
inMusic GmbH
Harkortstr.
12
-32
40880 Ratingen
GERMANY
World Headquarters inMusic Brands, Inc.
200 Scenic View Drive
Cumberland,
RI
02864
USA
Tel: 401-659-8192
Fax:401-658-3640
U.K. Office inMusic Europe, Ltd.
Unit 3, Nexus Park
Lysons Avenue
Ash Vale
HAMPSHIRE
GU12 5QE
UNITED KINGDOM
Tel: 01252 896 040
Fax: 01252 896
021
Germany Office inMusic GmbH
Harkortstr. 12 -32
40880 Ratingen
GERMANY
Tel: 02102 7402 20150
Fax: 02102 7402 20011
ranecommercial.com
7-51-1382-F NF04885-1.2
Other Rane Amplifier manuals
