raumplus LEGNO User manual

5.19.1.
(2019-08-28)Version 1.7
bc
Subject to technical changes.
Assemble
easy medium difcult
INTERIOR SYSTEM: ASSEMBLY INSTRUCTION
TROUSER PULL OUT

2
02
VERSION INFORMATION:
Version 1.4:
1.5:
1.6:
1.7:
n
n
n
n
n
n
n
04
06
07
17
18
03
CONTENT AND TOOLS
CONTENT:
TOOLS:
(without claim of completeness)
Added mounting cover / dividing rail / mounting holes and end caps / min.
max. trousers / updated part numbers and detail drawing / total views added
Front facing modied
Front facing / gap dimension 3 mm or 5 mm possible
corrected drilling measurement.
hack saw
allen key 4 mm
drilling machine
drill metal 5 mm
screwdriver set
pencil
cordless screwdriver
pageContent and tools
Productinformation
Accessories
Detail drawings
Off dimensions
Drilling aluminium frame
Position velcro
page
page
page
page
page
page

3
SYSTEM:
SYMBOLE: Symbol
=
=
=
=
System Information:
500 mm / 1200 mm
470 mm
500 mm
521 mm
PRODUCT INFORMATION
GENERAL INFORMATION:
Importance
Risk or danger!
Advice and information
„yes“ and „right“
„no“ and „wrong“
Follow the order
Preparation
nThis manual is part of the product and describes the safe and proper installation
of the system. Please read the instructions carefully before installation
n Please note that the assembly should only be done by qualied and trained staff in
strict compliance with all details indicated in this document. Improper installation in
variation from manufacturer’s specication may cause defects and danger, thus
endangering the safe xing of the product as well as the safety of the prospective
user. The liability of the manufacturer shall be excluded in case of defects
and consequential damages resulting from incorrect assembly of this product.
nPlease check the completeness of the delivered parts and check carefully if any
transport damages are visible.
n If any parts are damaged or lost, please immediately contact the responsible supplier.
n It is assumed that you have exactly identied all cutting dimensions according to
the measurement instruction for raumplus products.
Directional data /
direction of movement
Additional information /
other documents
nmin./ max. Cabinet shelf width
n xed depth
n Uno shelf depth min.
n Cornice shelf depth min
Trouser pull out
(with front facing 25 mm)

4
4_ 5_ 6_
1_ 2_ 3_89.31.023
89.31.053
89.31.022
89.31.052
89.31.020
89.31.050
10.89.013 26.33.020
26.33.050
89.31.025
ACCESSORIES
silver
dark bronze
silver
dark bronze
1_ side for trouser pull out
2_ front-/ back for trouser pull out
3_ tube for trouser pull out
4_ pilaster strip for tube
5_ dividing rail to be glued 18 mm
6_ glider for trouser pull out
silver
dark bronze
silver
dark bronze

5
7_ 8_ 9_
10_ 11_ 12_
13_
89.31.024 89.31.028 82.10.164
89.31.021 10.10.055 89.31.027
30.14.015
89.31.029
25.12.042
ACCESSORIES
7_ tapping screw cylinder head 4.8 x 19
8_ chipboard screw 4 x 20
9_ euroscrew 6.3 x 11
10_ end cap for trouser pull-out for 5 mm hole, black
11_ self-closing drawer runner 450 mm
12_ metal sheet screw 3.5 x 13
13_ drilling template trouser pull out, optional
w/o illustration
14_ velcro tape set
15_ double side tape for dividing rail 15 mm

6
DETAIL DRAWING
TROUSER PULL OUT COMPLETE

7
ca.650 mm
LEGNO / ECOLINE / FLUA
ASSEMBLY INSTRUCTIONS

8
440
= 440 mm
= 383 mm
= 383 mm
6485
7555
8625
9695
10 765
11 835
12 905
13 975
14 1045
15 1115
16 1185
LEGNO / ECOLINE / FLUA
CUTTING DIMENSIONS
trouser pull out width = clear width -10 mm
width front-/ backpiece = clear width -62 mm
width front facing = clear width -4 mm
Fixed dimensions:
optional
doubling
number
of
trousers
side piece length
tube length
pilaster length
number of trousers = width front-/ backpiece : 70
Please round results.
per
clear width
in mm:
optional
doubling
clear width

9
A
A
A - A
26
26 2
2
35115 115
53
115
25
LEGNO / ECOLINE / FLUA
2_
1_
35115 115
53
POSITION FRONT FACING
To change the gap measure from 3 mm to 5 mm loosen the front facing and
turn it with 180°, after that the marker hole has to be on the top.
marker hole on top!
marker hole bottom!
5 mm gap = 16 mm 3 mm gap = 18 mm
marker hole
marker hole

10
ca.650 mm
UNO
ASSEMBLY INSTRUCTIONS

11
440
30
= 440 mm
= 383 mm
= 383 mm
4500
6600
7700
8800
10 900
11 1000
13 1100
14 1200
UNO
panel width
trouser pull out width = panel width -120 mm
width front-/ backpiece = panel width -172 mm
width front facing = panel width -4 mm
CUTTING DIMENSIONS
number of trousers = width front-/ backpiece : 70
Please round the results.
Fixed dimensions:
side piece length
tube length
pilaster length
number
of
trousers
per
clear width
in mm:

12
A
A
A - A
6060
115
2626
25
35115 115
53
UNO
1_
2_
POSITION FRONT FACING
35115 115
53
To change the gap measure from 3 mm to 5 mm loosen the front facing and
turn it with 180°, after that the marker hole has to be on the top.
marker hole on top!
marker hole bottom!
5 mm gap = 16 mm 3 mm gap = 18 mm
marker hole
marker hole

13
CORNICE
ASSEMBLY INSTRUCTIONS

14
440
25 86
4500
6600
7700
8800
10 900
11 1000
13 1100
14 1200
CORNICE
CUTTING DIMENSIONS
panel width
trouser pull out width = panel width -120 mm
width front-/ backpiece = panel width -172 mm
width cover = panel width -4 mm

15
A
A
A - A
5858
115
2626
30
35115 115
53
CORNICE
1_
2_
DETAIL DRAWING
5 mm gap = 16 mm 3 mm gap = 18 mm
marker hole
marker hole

16
10
8
11
5
6
7
34
2
1
9
12
1 8
2 3
3 2
4 1
5 2
6 2
7 2
8 2
9 1
10 1
11 1
12 8
89.31.024
89.31.028
89.31.022 / 052
89.31.023 / 053
26.33.202 / 030
25.12.042
89.31.027
89.31.025
89.31.020 / 050
10.89.013
89.31.021
DETAIL DRAWING
EXPLODED DRAWING
object quantity item item no.
item list
tapping screw cylinder head 4.8 x 19
chipboard screw 4x20
front-/ back for trouser pull out
front facing
side for trouser pull out
dividing rail to be glued 18mm
double side tape for dividing rail
metal sheet screw 3.5x13
glider for trouser pull out
tube for trouser pull out
pilaster strip for tube
end cap for trouser pull-out

17



21,7
6,3
40
½
100
440
13
10
4,5
5
2_ holes front piece
1_ Drilling aluminum frame trouser pull out / holes side pieces
ASSEMBLY INSTRUCTIONS

18
80
40 310
40
1_ Position velcro
2_ Screw the frame screws with the cordless screwdriver and hex key 4 mm.
ASSEMBLY INSTRUCTIONS
POSITION VELCRO / ASSEMBLY

19
1_ Screw on cover from inside with chipboard screw 4 x 20.
The excess lenght left, right, top and bottom, depends on the system used.
2_ Please glue both dividing rails with double-sided tape from inside on the cut-outs of the front and rear part and plug in
the end caps.
ASSEMBLY INSTRUCTIONS
MOUNT FRONT FACING / DIVIDING RAIL / END CAPS

20 raumplus GmbH • Dortmunder Straße Bremen • Germany • Tel: +49 (0) 421 / 579 50 0 • Fax: +49 (0) 421 / 579 50 11 • www.raumplus.com
1_ Trouser pull out with front facing
DETAIL DRAWING
TROUSER PULL OUT