Ravas PR-INT-MX-RAVAS-ABLE User manual

Printer manual
* If your printer is not shown in this picture diagram, please contact your supplier.
We would like to inform you about the fact that this RAVAS product is 100 % recyclable on the basis that the parts
are processed and disposed off in the right manner.
More information can be found on our website www.ravas.com.
Rev.20150617
Printing/typographical errors and model changes reserved

Page 2of 26
Printer manual
PRINTER Page
PR-INT-MX-RAVAS-ABLE 4
Picture 4
Paper change 4
Inkt ribbon change 5
paper rolls 5
PR-INT-TH-RAVAS-MPP8250 6
Picture 6
Paper change 6
paper rolls 7
PR-INT-TH-XTRA 8
Picture 8
Paper change 8
paper rolls 9
PR-EXT-TH-RAVAS-7810V 10
Picture 10
Paper change 10
paper rolls 10
PR-EXT-MX-MCPK6701 11
Picture 11
Paper change 11
Inkt ribbon change 12
paper rolls 13
PR-STAR 14
Picture 14
Paper change 14
Inkt ribbon change 15
paper rolls 16
PR-STAR-PIN 17
Picture 17
Paper change 17
Inkt ribbon change 18
paper rolls 19
PR-TM-295 20
Picture 20
Paper loading 20
Inkt ribbon change 22
Paper 23

Page 3of 26
Printer manual
PR-ZEBRA-GK420D
Picture
Paper change
paper rolls
PR-EXT-TH-BLT-3”
Picture
Paper change
paper rolls

Page 4of 26
Printer manual
PR-INT-MX-RAVAS-ABLE
Picture
Paper change
Drawing 1
Drawing 2
Turn off the weighing system.
In order to open, move the left key (see drawing 1) to the right. At the same time pull the printer
door towards you.
Remove the empty paper roll from the holder.
Place a new paper roll on the holder. Pay attention to the correct placing of the roll in regard to
the unwinding side of the paper (see drawing 2 for the correct installation).
Feed the paper in the printer head (see drawing 2 for the correct installation).
Upon feeding the paper a light resistance is felt.
Turn on the weighing system.
By pressing the print feed key, the paper is transported further into the printer head (the print
feed key is located on the inside of the printer housing; at the top on the right a messing strip
with a little catch. This is the extension of the printer feed key).
The paper appears at the front of the printer head.

Page 5of 26
Printer manual
Close the printer door (push until you hear a click).
The weighing system and printer are ready for use.
Inkt ribbon change
Open the printer as shown above.
Take hold of the printer door between thumb and index finger and push the inner chassis slightly
downwards with your middle finger.
With your other hand carefully pull the inner chassis loose from the outer chassis (see drawing 3).
Hinge both parts as far apart from each other as possible and remove the ink ribbon by pushing on
one side (mentioning PUSH) of the ink ribbon cassette.
The ink ribbon pops out and can be changed (see drawing 4).
drawing 3 drawing 4 Picture inkt ribbon
Paper rolls
Order nr.:
Description:
Dimensions:
PRP-PAP-RAVAS-57-50-12
paper, single, white
57xØ50xØ12 mm.
PRP-PAP-RAVAS-57-50-12-DOUBLE
paper, double, white/yellow
57xØ50xØ12 mm.

Page 6of 26
Printer manual
PR-INT-TH-RAVAS-MPP8250
Picture
Paper change
Drawing 1
Drawing 2
In order to open, pull the lever until the lid is released from its locked position. To avoid damage,
do not use eccesive force. See drawing 1 and 2.

Page 7of 26
Printer manual
Remove the empty paper roll from the holder.
For replacing a new paper roll, reel off a few centimeters from the new paper roll. Hold
approximately 5 cm. of paper outside the device as you place the new roll into the reservoir.
Close the lid by applying equal amounts of pressure on each side ensuring the lid is in locked
position.
Tear off the spare paper.
Paper rolls
Order nr.:
Description:
Dimensions:
PRP-PAP-INT-TH-RAVAS
Thermal paper, white
57xØ50xØ18 mm.
PRP-PAP-CU-ST-TH-RAVAS
Thermal, self adhesive, white
57xØ50xØ12 mm.

Page 8of 26
Printer manual
PR-INT-TH-XTRA
Picture
Paper change
Picture 1
Picture 2

Page 9of 26
Printer manual
Picture 3
Picture 4
In order to open, pull the lever until the lid is released from its locked position. To avoid damage,
do not use eccesive force. See picture 1.
Remove the empty paper roll from the holder. See picture 2.
For replacing a new paper roll, reel off a few centimeters from the new paper roll. Hold
approximately 5 cm. of paper outside the device as you place the new roll into the reservoir. See
picture 3.
Close the lid by applying equal amounts of pressure on each side ensuring the lid is in locked
position. See picture 4.
Tear off the spare paper.
Paper rolls
Order nr.:
Description:
Dimensions:
PRP-PAP-TH-RAVAS-58-32-12
Thermal paper, white
58xØ32xØ12 mm.

Page 10 of 26
Printer manual
PR-EXT-TH-RAVAS-7810V
Picture
Paper change
In order to open, pull the lever until the lid is released from its locked position. To avoid damage,
do not use eccesive force.
Remove the empty paper roll from the holder.
For replacing a new paper roll, reel off a few centimeters from the new paper roll. Hold
approximately 5 cm. of paper outside the device as you place the new roll into the reservoir.
Close the lid by applying equal amounts of pressure on each side ensuring the lid is in locked
position.
Tear off the spare paper.
Paper rolls
Order nr.:
Description:
Dimensions:
PRP-PAP-INT-TH-RAVAS
Thermal paper, white
57xØ50xØ18 mm.
PRP-PAP-CU-ST-TH-RAVAS
Thermal, self adhesive, white
57xØ50xØ12 mm.

Page 11 of 26
Printer manual
PR-EXT-MX-MCPK6701
Picture
Paper change
In order to open, squeeze the lid carefully sideways and pull it up. To avoid damage, do not use
eccesive force.
Drawing 1
Drawing 2

Page 12 of 26
Printer manual
Remove the remaining paper using the Paper Feed button, do not pull paper out of the rear of the printer
mechanism.
Reel off a few centimetres from a new roll of paper and check that the end has a clean straight edge (see
drawing 1).
Slide the leading edge of the paper through the paper entry slot, with the leading edge of the paper feeding
forwards from the bottom of the roll, until you feel resistance.
Press the paper feed button and feed the paper through the printer mechanism. (see drawing 2) Keep the
paper feed button depressed until enough paper is fed through the printer mechanism to pass through
the paper exit slot.
Slide the new paper roll in the paper cup and close the lid.
Inkt ribbon change
In order to open, squeeze the lid carefully sideways and pull it up. To avoid damage, do not use
eccesive force.
Remove the old ribbon by gently pulling at the ends of the plastic housing. See picture 1.
Place the new ribbon (see picture 2)in the same position. Make sure the paper is between the ribbon and
the plastic ribbon housing. See picture 3.
Gently press the ribbon holder on its place by pushing on top of the ends. See picture 4.
Picture 1
Picture 2

Page 13 of 26
Printer manual
Picture 3
Picture 4
Paper rolls
Order nr.:
Description:
Dimensions:
PRP-PAP-RAVAS-57-50-12
paper, single, white
57xØ50xØ12 mm.
PRP-PAP-RAVAS-57-50-12-DOUBLE
paper, double, white/yellow
57xØ50xØ12 mm.

Page 14 of 26
Printer manual
PR-STAR
Picture
Paper change
Turn off the power of the printer.
Cut the Roll Paper end straight and square. Hold the roll so that the paper comes from the
bottom.
Attach the Roll Paper to the Holders Paper by slipping one side of the roll onto the Hub and
pulling the other Hub out to allow the roll to slip in place.
Insert the paper evenly into the Paper Insertion Slot.
Turn the Power Switch “ON”, and press the FEED Button. The paper will be fed into the unit.

Page 15 of 26
Printer manual
Inkt ribbon change
Turn off the printer power.
In order to open, lift the lid (see drawing 1) upwards.
NOTE: Be careful not to touch the print head immediately after printing, because it can get very hot.
Drawing 1
To remove the old inkt ribbon, Hold the spool and lift gently, rotating it until the ribbon sags.
Push the ribbon detecting lever out, lift the spool until it comes off the shaft. Remove the second
spool in a similar manner. (See drawing 2). (Do not apply excessive force when lifting spools.).

Page 16 of 26
Printer manual
Drawing 2
Unwind ribbon so that the spools are separated as shown in drawing 3.
Drawing 3
Hold the ribbon taut as shown with the drive pins facing down and slide the ribbon between the
print head and the platen. While keeping the ribbon taut, wrap one side around the black ribbon
guide on the end of the platen and drop one spool on the spool shaft. As you move the spool
downwards, move the detecting lever aside to allow the spool to drop into place. Make sure the
spool drive pins engage with the spool drive holes. As the spool drops into place there will be a
click.
While continuing to hold the ribbon taut, install the remaining ribbon spool in a similar fashion.
Turn the spool that rotates freely to take up the ribbon slack.
Paper rolls
Order nr.:
Description:
Dimensions:
PRP-PAP-STAR
paper, single, friction feed, white
114xØ70xØ12 mm.

Page 17 of 26
Printer manual
PRP-PAP-STAR-2
paper, double, friction feed, white/yellow
114xØ70xØ12 mm.
PR-STAR-PIN
Picture
Paper change
Turn off the power of the printer.
To remove the old paper, cut the paper close to the slot and use the feed button until paper has
passed completely through the printer.
Note: Do not try to remove the paper by hand as it could become crooked and get jammed inside
the printer.
For placing the new paper, make a straight cut along the top of the paper, about 1/4 inch away
from the sprocket holes, (as shown in the drawing 1). If there is perforation, cut the paper on the
perforation.

Page 18 of 26
Printer manual
Drawing 1
Insert the paper squarely into the paper insertion slot until the ALARM lamp goes out. Then, hold
down the FEED switch to advance the paper 8 lines, and release the switch when 8-line feeding is
completed. If the paper is not fed straight during 8-line feeding, straighten the paper by pulling it
back slowly as you hold the paper release lever down. If a sprockethole is torn or enlarged, recut
the paper and reinsert it as before.
After confirming that the paper has been fed in straight, feed the paper continuously by holding
the feed switch down.
Release the feed switch when the paper emerges through the paper outlet.
Inkt ribbon change
Turn off the printer power.
In order to open, lift the lid (see drawing 1) upwards.
NOTE: Be careful not to touch the print head immediately after printing, because it can get very hot.
Drawing 1

Page 19 of 26
Printer manual
To remove the old inkt ribbon, Hold the spool and lift gently, rotating it until the ribbon sags.
Push the ribbon detecting lever out, lift the spool until it comes off the shaft. Remove the second
spool in a similar manner. (See drawing 2). (Do not apply excessive force when lifting spools.).
Drawing 2
Unwind ribbon so that the spools are separated as shown in drawing 3.
Drawing 3
Hold the ribbon taut as shown with the drive pins facing down and slide the ribbon between the
print head and the platen. While keeping the ribbon taut, wrap one side around the black ribbon
guide on the end of the platen and drop one spool on the spool shaft. As you move the spool
downwards, move the detecting lever aside to allow the spool to drop into place. Make sure the
spool drive pins engage with the spool drive holes. As the spool drops into place there will be a
click.
While continuing to hold the ribbon taut, install the remaining ribbon spool in a similar fashion.
Turn the spool that rotates freely to take up the ribbon slack.
Paper rolls
Order nr.:
Description:
Dimensions:
PRP-PAP-STAR-PIN
paper, single, pin feed, white
114xØ70xØ12 mm.
PRP-PAP-STAR-ADH
paper, self adhesive, pin feed, white
114xØ70xØ12 mm.

Page 20 of 26
Printer manual
PR-TM-295
Picture
Paper loading
Use only the specified type of paper for this printer. Do not use inappropriate types of paper, or it could
cause malfunction or damage of the printer.
The following procedure describes how to print on paper. Before trying to print,be sure to install a
ribbon cassette into the printer using the procedure under “inkt ribbon change” on page 22.
Make sure that the printer is plugged in and turned on.
Check that the RELEASE indicator on the control panel is lit. If the indicator is not lit, press the
RELEASE button until the indicator lights up.
Important!
Insertion and removal of paper should be done only when the printer is released condition (the paper is
not held by paper feed roller).
ENGLISH
Place a piece of the paper onto the printer’s document table and slide its right edge into the
printer. Printing will be performed on the side of the paper that is facing up (the one you can
see), starting from the top of the paper.
Important!
Do not use wrinkled or curled paper. In case of multiple paper, neatly align the
sheets.