Rayburn Heatranger 480AG (CF) User manual

THIS APPLIANCE MUST BE INSTALLED IN
ACCORDANCE WITH THE RULES IN FORCE AND
USED ONLY IN A SUFFICIENTLY VENTILATED SPACE.
Thank you for buying this Rayburn appliance. We want
you to get the best from it, so please read this leaflet
carefully and follow the instructions before using your
Rayburn for the first time.
Your Rayburn has been designed to provide cooking,
central heating and domestic hot water when you require
it. Two separate burners provide heat for the appliance.
The cooker burner provides heat for the cooking whilst the
boiler burner provides heat for the central heating and
domestic hot water requirements.
The cooker burner should be set to run continuously alight
- at a low rate and full rate upon operation of the
thermostat.
The boiler burner is designed to operate on demand and
can be electrically controlled by a time switch or
programmer to give selected heating use.
An optional Rayburn programmer is available from your
Rayburn stockist, which will control your cooking function.
An ideal extra for people who wish to combine traditional
elegance with today’s lifestyle.
You will find supplied with your Rayburn the following:-
1 Solid Shelf 1 Customer Log Book
2 Grid Shelves 1 Warranty Document
1 Meat Tin 1 Installation and Servicing
1 Grill Rack Instructions
1 Cookbook 1 Operating Instructions
DO NOT USE THIS APPLIANCE TO WARM A ROOM
WITH THE APPLIANCE DOORS LEFT OPEN.
DO NOT LEAVE THE ROASTING OVEN DOOR OPEN -
If left open for any length of time over-heating may cause
damage to some components within the appliance.
Consumer Protection
As responsible manufacturers we take care to make sure that our
products are designed and constructed to meet the required safety
standards when properly installed and used.
IMPORTANT NOTICE: PLEASE READ THE ACCOMPANYING
WARRANTY.
Any alteration that is not approved by AGA, could invalidate the
approval of the appliance, the warranty and could also infringe the
current issue of the statutory requirements.
IMPORTANT:
This appliance could contain any of the materials that are
indicated. It is the Users/Installers responsibility to ensure that the
necessary personal protective clothing is worn when handling, where
applicable, the pertinent parts that contain any of the listed materials
that could be interpreted as being injurious to health and safety, see
below for information.
Firebricks, Fuel beds, Artificial Fuels – when handling use
disposable gloves.
Fire cement – when handling use disposable gloves.
Glues and sealants – exercise caution – if these are still in liquid
form use face mask and disposable gloves.
Glass Yarn, Mineral Wool, Insulation Pads, Ceramic Fibre,
Kerosene Oil – may be harmful if inhaled, may be irritating to skin,
eyes, nose and throat. When handling avoid inhaling and contact
with skin or eyes. Use disposable gloves, face masks and eye
protection. After handling wash hands and other exposed parts.
When disposing of the product reduce dust with water spray, ensure
that parts are securely wrapped.
Operating Instructions for
Rayburn Heatranger 480AG (CF)/480AL (CF)
Gas Fired Central Heating Cooker
FOR USE IN GB & IE
PLEASE READ THESE INSTRUCTIONS BEFORE USING THIS APPLIANCE
INTRODUCTION
1 01/10 EOPI 512113
[email protected]
DESN 512129

SECTION PAGE
INTRODUCTION 1
CONTROLS AND USER INFORMATION 3
INSTRUCTIONS - LIGHTING THE PILOT 4
MAIN BURNER LIGHTING
TO USE THE BOILER 5
THE COOKER AND PROGRAMMER (OPTIONAL) 6
COOKING HINTS 7
CLEANING AND CARE FOR YOUR RAYBURN 8
MAINTENANCE, GAS LEAK OR FAULT, COMBUSTION DISCHARGE 9
SAFETY DEVICE, AIR ENTRY LOUVRES AND VENTILATION
2
Contents

3
DESN 511779
MARK APPROX
TEMP ºC
LOW 120
140
150
170
180
190
200
220
230
240
250
1
2
3
4
5
6
7
8
9
HIGH
MAIN OVEN TEMPERATURE SETTING
CHART
CONTROLS
USER INFORMATION
H
DOOR OPENING
TO OPEN - TWIST HANDLE TO
RELEASE FROM DOOR CATCH
AND PULL OPEN
ENSURE SHELVES ARE
INSERTED AS SHOWN
THE THERMODIAL ON THE MAIN OVEN DOOR IS A
GUIDE TO THE CENTRE OVEN TEMPERATURE
WHEN COOKING SEE COOKING CHART ON PAGE
3 AND COOKING HINTS ON PAGE 6 FOR FURTHER
INFORMATION.

LIGHTING
Lighting instructions can also be found on an instruction
plate on the inside of the burner door.
Boiler
This appliance is fitted with an automatic ignition unit that
will light the main burner on demand. Should button (K)
(see Fig. 1) be illuminated press button, this will allow the
burner ignition to continue, should the burner illuminate
again this will indicate a fault on the boiler burner, Contact
your local Gas Safe Registered engineer to correct the
fault.
Cooker (See Fig. 1)
Turn on gas cock (E).
Press in and hold the cooker flame failure override button
(C) allowing a few seconds for the gas to reach the cooker
pilot.
Press the piezo ignitor button (D) and the pilot burner will
light.
Continue to hold the button for 15 seconds after the pilot
has been lit so that when the button is released, the pilot
should remain alight. If it does not, WAIT 3 MINUTES then
repeat the procedure.
Ensure the electricity supply is turned ON and set any
external controls to the ON position.
Turn the boiler thermostat knob to ‘MAX’, and the boiler
burner will light to full rate.
Turn the cooker thermostat knob to ‘H’, and the cooker
burner will cross light to full rate.
NOTE: SMOKE/SMELL EMITTED DURING INITIAL
USAGE
Some parts of the cooker have been coated with a light
coating of protective oil. During initial operation of the
cooker, this may cause smoke/smell to be emitted and is
normal and not a fault with the appliance, it is therefore
advisable to open doors and or windows to allow for
ventilation. Lift the lids to prevent staining the linings.
INSTRUCTIONS
4
FIG. 1 DESN 512964
C - COOKER FLAME FAILURE OVERRIDE
BUTTON
D - PIEZO IGNITION BUTTON - COOKER
E - GAS COCK - COOKER
G - GAS COCK - BOILER
K - BOILER BURNER RESET

The operation of the boiler can be automatic if a
programmer is fitted. This may also be used in
conjunction with a room thermostat or other devices to
control temperature.
The boiler thermostat control knob controls the
temperature of the hot water.
The boiler thermostat control knob is situated behind the
control door on the left hand side of the controls facia
panel (See Fig. 2).
Turning the control knob clockwise will increase the
temperature of the boiler which will provide hot water to
the radiators and to the hot water cylinder.
For safety shutdown purposes an overheat thermostat is
included (as shown in Fig. 2).
This will operate only if the water temperature in the
system is in excess of 95°C. This indicates a system fault
and it should be determined by your local service
engineer and rectified before re-lighting the boiler.
TO USE THE BOILER
5
FIG. 2
DESN 512149
COOKER OVEN
THERMOSTAT KNOB
CDSD RESET
BUTTON
BOILER OVERHEAT
THERMOSTAT RESET
BUTTON
BOILER
THERMOSTAT KNOB