Raycon Move Wing RD 200 User manual

2
Baery：
Transmier Baery: 4*AA baery (Not including)
Quadcopter Baery ( Built-in ) : 7.4V/1200 mAh Li-po baery inside
Flying me: 7-10 minutes
Charging me: About 240 minutes
Flying distance: >150 meters
MOVE WING weight: 510 gram
MOVE WING Size:L:66cmxW:56cmxH:15.5cm
Main technical contents:
2.4G TRANSMITTER INSTRUCTION:
On/off switch
Fast/slow speed
Turn right trim Le side fly trim
Backward trim
Headless mode
Throle/Rudder
Light control
Turn le trim
One key unlcok/Landing
Right side fly trim
Forward trim
Elevator/Aileron
(Forward/Backwar/Right/Le)
Take video/photo
Required 4*AA baery
Short press:take photo
Long press: take video
(VGA/480P camera without
this funcon)

3
 25.400 25.400 
The landing gear installation instruction(Optional accessories)：
Camera Installation Instruction (Optional):
Installation Instructions for Drone Protection Cover :
(figure 12）(figure 10） (figure 11）
(figure 9）(figure 7） (figure 8）
(figure 6）(figure 4） (figure 5）
Take the landing skid and place it into the support frame(Figure 10/11). Firmly
screw (PA2.0x10 screws) in the landing skid to the frame with a screwdriver
(Figure 12).
(figure 1） (figure 2） (figure 3）
front
back
bladeA
bladeA
bladeB
bladeB
Remote control installation instructions:
1. Use screwdriver to open the battery cover（figure 1）
2. Base on the instruction in the battery slot to put
battery（figure 2）
3. Tighten the screws in battery cover（figure 3）
Blade installaction location:
BB
B
B
B B
A
A
A
A
B B
B
B
BB
VIDEO
Take the camera and place it into the battery cover.(Image 4/5 )Firmly screw
(PA2.0×10 screws)in the camera to the battery cover with a screwdriver .Then
attach the camera cable to the drone .(Image6)
Take the drone protection cover and place it into the motor shell.(Image 7 /8 )
Firmly screw (PB1.4×6 screws) to screws hole with a screwdriver .(Image 9)
Power switch

4
4
Fine-tuning operaon:
Left Right
Left Right
Forward/Backward fine-tuning
Up
Down
Front
Anti-Clockwise Clockwise
Sideward fly fine-tuning
Turn le/right fine-tuning
When the quadcopter keeps flying forward/
backward, you can correct it by pressing
fine-tunning button down/up.
When the quadcopter keeps flying sideward,
you can correct it by pressing fine-tuning
button left/right.
When the quadcopter keeps rolling/head
move left/right, fix it by pressing fine-tuning
button left to right/right to left.
1. “Front”“Back”as the right figure, Place quadcopter on
level ground, put quadcopter’s head in front. Back aim
at transmitter.
2. Pls push the bottom of the power switch to ON position, at
the same time ,the light will be fast flash.
3. Open the transmitter switch, push the throttle stick,
then pull down the throttle stick, the transmitter’s indicator
light will be stable, the quadcopter’s light also stable,
it means frequency connect sucessfully.
4. Following figures shows three ways unlock. Four paddles
will be rotate slowly when quadcopter unlock, it means unlock sucessfully.
Frequency connect/Unlock:
Flying operaon introducon:
Pull the elevator/aileron left or right,
the quadcopter flies to left side or right side.
Pull the throttle left or right, the
quadcopter nose turns to left or right.
Push the elevator/aileron up or down,
the quadcopter flies forward or backward.
Push the throttle up or down, the
quadcopter flies upward or downward.
Hover up and down Forward and backward
Turn le and right Sideward fly
Front
front
back
Power
switch

Noted: After unlock, if do not do any operation, about 10 seconds, motor will be stop
automatically. If need to quick stop after start, just re-do unlock operation.
Throle/Rudder
(turn)
Throle/Rudder
(turn) One key unlock/landingFront/back/Le / right side fly rudder
Front/back/Le /
right side fly rudder
5
Environment for flight:
Distance of 3M
Distance of 2.5M
Distance of 3M
Distance of 2M
Distance of 3M
Please have good practice before go to flight
（Figure2）（Figure1）
Battery
Battery Plug
Battery socket
7.4V1200mAh Li-po baery USB charger
Charger
（Excluded)
Front
Front
Turn Turn
Front Front
Baery charging using instrucon:
Headless mode operaon instrucon:
When charging, please put the drone on a dry area and keep it far away from
heat source or explosive divices.
After flying, please do not charge the battery if the surface temperature is still not
cool. Otherwise it may cause a swollen battery or even a fire hazard.
Please make sure that you use the original adopter provided with the drone and
When the battery has been used for a long time, or appears to be swollen, please
replace them.
If not in use for a long time will lose its charge automatically charging or
discharging too often may reduce its life.
Warning on Li-poly baery:
1. Battery installation: open battery door, install battery into battery socket, battery's
plug aim to drone's power plug, cover the battery door (Figure1).
2. Battery charging: remove the battery from drone, battery plug aim to USB adopter
to charge(Figure2). It will has LED red light on adopter when charge, after 240
minutes it will be off when charge completely.
3. During the normal flight, if drone light flash rapidly, it means need to replace
the battery/re-charge the battery.
1. Headless mode function instruction:
The functioning of headless mode is pretty simple.
Only pre-requisite is that before taking off,
you’re required to position the drone in such a
way that its front is your front. Since yaw (the
left stick) anyway doesn’t have anything to do
with orientation(left is left and right is right all
the time, regardless of where your drone is pointing
at), it is how the drone reacts to rudder(the right
stick)that changes. In other words, even when
you turn your drone 90 degrees to the left.
2. How to set headless mode:
Base on”Reset operation introduction”third steps to reset headless mode firstly.
Press the headless mode button after quadcopter fly. lf you don’t want to use
headless mode, just only press headless mode button again.

6
Part-01 Part-02 Part-03
Part-07 Part-08 Part-09
Part-10 Part-11 Part-12
Part-04 Part-05 Part-06
7.4V 1200 mAh Li-po battery
Main Blade A /B
RCB Board
Charger Motor Cover
Main Motor Main Frame
Landing Gear
Main Spare parts:
Transmitter
Camera Accessories
Upper Body
Red/Blue Line Motor
Red/Black Line Motor
Reset opertaion introducon:
(Figure 2)
(Figure 1)
1.Transmitter reset: When transmitter cannot control quadcopter normally, pls turn
off transmitter, then re-turn on transmitter, transmitter will reset automatically.
2.Quadcopter reset: When quadcopter cannot fly normally,
also the transmitter already reset, at this time, you can try
to reset the quadcopter. Reset way: Place the quadcopter
on the level ground, turn on, after frequency connect, pull
down transmitter rudder to left, keep 2-3 seconds, wait
quadcopter light turn flash to stable(Figure 1).
3.Headless mode adjust: If need to turn on headless mode
during play before quadcopter fly up, must adjust
headless mode first(Must adjust headless mode for every
time flight). Adjust way: Place quadcopter on the level
ground, head in front, back aim to controller before turn
on quadcopter, frequency connect, then pull down
transmitter rudder to right, keep 2-3 seconds, wait
quadcopter light turn flash to stable(Figure 2).
Front/back/Le /
right side fly Rudder
Throle/Rudder(tun)
Throle/Rudder(tun) Front/back/Le/
right side fly Rudder

2
(Figure 1)
(Figure 2)
(Figure 3)
(Figure 4)
1.Smartphone WIFI Connection: Turn on the quadcopter and place on a flat surface.
The LED light on the camera will turn red. After about 15 seconds, the light will
flash blue indicating it is transmitting a Wifi signal. Enter the menu in the smart
phone, open the Wifi setting and search for "FPV-WIFI-****FPV" signal. Connect
to "FPV-WIFI-****FPV" signal. When connect successfully, the red LED light light
off, blue LED light light stable. Exit the phone set.
Smartphone APP Control Instrucons
1 Icon: Take photo, automatically saves to phone
and in icon 4 document.
2 Icon: Smartphone take video, press after take
video(icon turn red), automatically saves
to phone and in icon 4 document.
3 Icon: Smartphone file, check photo and video.
4 Icon: Wifi signal.
5 Icon: 2D/3D Image transfer, only real-time transmission has this function.
6 Icon: Return.
7 Icon: Icon instruction manual.
480P control interface”(Figure 4)
3.Smartphone APP Interface Function:
Open the downloaded App "WIFI CAMERA"by
pressing on the this icon . The APP will open
to main page(Figure 1). If camera is 720P, press
icon, enter 720P control interface, if
camera is 480P, press icon, enter 480P
control interface.
2.Operate Smart Phone App:
1 Icon: Take photo, automatically saves to phone
and in icon 4 document.
2 Icon: Smartphone display.
3 Icon: Smartphone take video, press after take
video(icon turn red), automatically saves
to phone and in icon 4 document.
4 Icon: Smartphone File, check photo and video.
5 Icon: Wifi signal.
6 Icon: TF card take photo, after press, screen
shows”Aerial photos”, save photo in
icon 9, smartphone or IT card.
7 Icon: TF card inserted , TF card not
inserted .
8 Icon: TF card take video, after press, screen
shows“Aerial photos”, at the same time icon
turn red, begin to take video, save to Icon 9 docment, smartphone or TF card.
9 Icon: TF file, check photo and video.
10 Icon: 2D/3D Image transfer, only real-time transmission has this function.
11 Icon: Return.
12 Icon: Icon instruction manual.
720P control interface”(Figure 3)