Rayleigh Instruments RI-F220 User manual

RI-F220-IM-V01
1
RI-F220-G-C
RI-F220-G-MB
RI-F220 Instrucon Manual
X 4
X 1
X 1
RTU
Pulse SO
Safety related nocaon, symbols and instrucons that appear in this
operang manual or on the equipment must be strictly followed to
ensure the safety of personnel as well as the instrument. If the
equipment is not used in a manner specied by the manufacturer it may
impair the protecon provided by the equipment
• Do not use the equipment if there are mechanical damage
• Do not exceed the stated maximum rangs of the device
• No repairs, maintenance or adjustments are possible
• Read the complete instrucon manual prior to installaon or
operang the unit
• The equipment in its installed state must not come into close
proximity to any heang sources, oils, steam, causc vapours or
other unwanted process by-products
• Do not use in hazardous or classied locaon where explosion or
other dangers can be triggered by the device
PRODUCT SAFETY INSTALLATION PRECAUTIONS
Risk of electric shock!
Only to be installed by a competent person
• To prevent the risk of electrocuon, always isolate and lock-o the
power supply to the equipment prior to undertaking any work
• Always conrm absence of electricity prior to starng work using
appropriate voltage detecon equipment
• Wiring shall be done strictly according to the terminal layout
• Conrm that all connecons are correct before energizing the
equipment
• Roung of cables shall be way from any internal EMI source
• Copper cable should be used
• All wiring to be in accordance with applicable local standards
Specicaons Accuracy
Wiring Input 3Ø 4 wire, 3Ø 3 wire, 2Ø 3 wire, 1Ø 2 wire Voltage V L-N and V L-L±0.5% of full scale
Rated Input Voltage 3x 11...300V AC (L-N), 19...519V AC (L-L) Current ±0.5% of full scale
Frequency Range 45...65Hz Frequency for L-N >20V, L-L >35V ±0.1% of full scale
CT Primary 1A/5A...10,000A congurable Acve, Reacve and Apparent Power 1%
CT Secondary 1A or 5A (max rang x1.2) Power Factor ±0.01 of Unity
VT Primary 100...500kV congurable Acve Energy Class 1 (IEC/EN 62053-21)
VT Secondary 100...500V AC (L-L) congurable Reacve Energy Class 2 (IEC/EN 62053-23)
Auxiliary / Power consumpon 85...270V AC 45...65Hz / < 8VA
Display Update Rate 1 sec all parameters Wh Resoluon and Default Pulse Weight
Operang / Storage Temperature -10…55°C / -20…75°C Wh Resoluon and Default Pulse Weight
Example
If CT = 100/5A (CT rao = 20) & VT = 350/350V (VT Rao = 1)
Wh resoluon = 0.1kWh (20 x 1 = <150) | Pulse O/P default = 0.1kwh/pulse
Humidity 0...85% non-condensing
Protecon Degree (IEC/EN60529) IP54 Front only (rubber gasket ed)
Pulse Output External 5...27V DC / 100mA max
Pulse Resoluon / Duraon 0.01...99.99kWh per imp / 0.1...2 sec
Communicaon Modbus RTU over RS485
MBus (EN13757)
CT Rao x VT Rao <15 <150 <1500 <15k <150k ≥150k
Wh / VArh / VAh 0.01k 0.1k 1k 0.01M 0.1M 1M
INT 0.01k 0.1k 1k 0.01M 0.1M 1M
0.001k 0.01k 0.1k 1k 0.01M 0.1M
MECHANICAL INSTALLATION
Installaon & Environmental
Panel mounted, indoor used only.
Installaon category: III
Altude: up to 2000 m
Protecon Class: II
Polluon degree: II
All terminal covers must be ed aer wiring
EO&E: Document subject to change
x4

RI-F220-IM-V01
2
WIRING
Modbus / MBus
Wiring Topology
Daisy Chain Star Network
A | B
Modbus ✓
+ | -
MBus ✓✓ 1 | 2
Typical Modbus
conguraon shown
For MBus interface
follow Wiring
Topology below
500m Max, ≤ 32 meters
Fuse class CC UL / fast acng 600V
Rang 0.5A
For ’Volt-free’ PLC or digital input,
voltage must be provided by the addion
of a DC PSU
Single Core
0.5 > 4mm2
Ø 2.5mm max
Stranded
0.5 > 2.5mm2+
7mm
Ø 2.5 mm
0.6 Nm
Max
3P4W
3 CTs
1P2W
1 CT
2P3W
2 CTs
2 VTs
2P3W
2 CTs
3P3W
2 CTs
2 VTs
3P3W
2 CTs
3P4W
3 CTs
3 VTs
Voltage
and current
must be
from same
phase
L1, L2 or L3
RS485 PULSE
O/P RS485 PULSE O/P RS485 PULSE O/P
RS485 PULSE
O/P
RS485 PULSE
O/P RS485 PULSE
O/P
RS485 PULSE
O/P
RS485 PULSE
O/P

RI-F220-IM-V01
3
F220-G-C
F220-G-MB
Seng Default Adjustment Range Network
& CT
Must
congure
VT
Adjust if
Using VT
Comms
Modbus /
MBus
Pulse O/P
Adjust if
ulised
System
Sengs
Oponal
11Change Password 1000 NO / YES (0000 - 9998) ✓
22Phase Network Selecon 3P4W 3P4W
3P3W
1P2r (Phase 1)
1P2Y (Phase 2)
1P2b (Phase 3)
✓
33CT Secondary (see CT Label) 51A / 5A ✓
44CT Primary (see CT Label) 51A/5A to 10,000A ✓
55PT Secondary 350 100V > 500V ✓
66PT Primary 350 100V > 500kV ✓
77Demand interval method Sliding Sliding / Fixed ✓
88Demand interval duraon 15 1 > 30 ✓
99Demand interval length 11 > 30 min ✓
10 10 Pulse Weight 0.10 0.01 > 99.99 kWh/imp ✓
11 11 Pulse Duraon 0.1 0.1 > 2.0 Sec ✓
12 12 Run Hour Selecon 00 > 10% ✓
13 13 Slave ID Modbus:
MBus (Primary ID):
1
1
1 > 255
1 > 250 ✓
14 14 Baud rate Modbus:
MBus:
9600
2400
300 > 19200 bps
1200 > 9600 ✓
15 15 Parity Modbus:
MBus:
None
Even
None / Odd / Even
Even ✓
16 16 Stop Bit Modbus:
MBus:
1
1
1 / 2
1✓
17 17 Back Light O (0000 = Never) 0000 0 > 7200 Sec ✓
X18 MBus Secondary ID Serial # 0000 0000 > 9999 9999 ✓
18 19 Factory Default No No / Yes Does not reset energy & demand values ✓
19 20 Reset Energy & Demand No No / Yes (Password +1) Once entered, reset each value individually ✓
CONFIGURATION
Step A: Enter Conguraon Menu Step B: Congure each seng, as required, referring to
Sengs Table below, using the buons as follow:
1Press buon once to make digit or opon ash, press
again to move ashing cursor
2Press to change digit or opon, press to move
cursor posion as required
3Press to save and move to next seng opon, Exit
menu once all sengs are congured (see Step 1)
Hold 3 Secs to
Enter Cong
(same to Exit)
Password = 1000
(Refer to Step B)
2
1

RI-F220-IM-V01
4
OPERATION
1 Funcons & displayed measurement indicators:
RS485 communicaon in progress
1,2,3 Phase L-N
12,23,13 Phase L-L
IM Imported Energy (posive value)
EP Exported Energy (negave value
Total Sum of 3-phase
DMD Max/Min Demand
TH Total Harmonic Distoron (THD)
Net Sum of 3-Phase Energy
2 Funcon buons and funcon symbols
3 Phase, total or average instantaneous measurements
(V, A, PF, Hz, kW, kVAr, kVA) >> V/I/VAF/PF/P buons
4 Accumulave Energy (kWh/kVArh/kVAh) >> E buon
No. of
Presses V/I VAF PF/P E
x1 Voltage (L-N) L1: V/A/Hz Power Factor L1 IM Acve Energy - kWh
x2 Voltage (L-L) L2: V/A/Hz L1: kW/kVAr/kVA/PF L2 IM Acve Energy - kWh
x3 Voltage THD (L-N) L3: V/A/Hz L2: kW/kVAr/kVA/PF L3 IM Acve Energy - kWh
x4 Voltage THD (L-L) Avg: V/A/PF/Hz (L-N) L3: kW/kVAr/kVA/PF L1 EP Acve Energy - kWh
x5 Current Avg: V/A/PF/Hz (L-L) ∑: kW/kVAr/kVA/PF L2 EP Acve Energy - kWh
x6 Current THD Max DMD: kW/kVAr/kVA L3 EP Acve Energy - kWh
x7 Current Max DMD Min DMD: kW/kVAr Net IM Acve Energy - kWh
Net EP Acve Energy - kWh
 L-N parameters not displayed For 3P3W
 Parameters in BOLD not displayed for 1P2W Net Acve Energy - kWh (IM+EP)
L1 IM Reacve Energy - kVArh
L2 IM Reacve Energy - kVArh
L3 IM Reacve Energy - kVArh
L1 EP Reacve Energy - kVArh
L2 EP Reacve Energy - kVArh
L3 EP Reacve Energy - kVArh
Net IM Reacve Energy - kVArh
Net EP Reacve Energy - kVArh
Net Reacve Energy - kVArh (IM+EP)
L1 Apparent Energy - kVAh
L2 Apparent Energy - kVAh
L3 Apparent Energy - kVAh
Net Apparent Energy - kVAh
Run Hour (0.01 hr = 36 sec)
Number of Auxiliary Switch ON
Voltage Phase Sequence
Serial Number
Page Scroll
OK-CLK = L1 → L2 → L3
ANTI-CK = Incorrect Order
INVAL Id = Missing Phase 
✓
Rayleigh Instruments Limited (Head Oce)
Raytel House, Cutlers Road, South Woodham Ferrers, Chelmsford, Essex. CM3 5WA
W: www.rayleigh.com E: [e-mail]
Rayleigh Instruments Limited SP. Z o.o. (European Oce)
Ul. Aleje Jerozolimskie 214, Warsaw, Poland, 02-486
W: www.rayleigh.pl E: [e-mail]
x8
x9
x10
x11
x12
x13
x14
x15
x16
x17
x18
x19
x20
x21
x22
x23
x24
Hold 3 sec
Hold 10 sec
de = Display Voltage Screen aer
60 sec of non-acvity
AUtO = Automac page scroll
Change every 5 sec
MAnL = Manually change page only
Hold 3 sec
Hold again to change