Rayleigh Instruments RI-F200 User manual

RI-F200-IM-V01
1
RI-F200-B-MB / RI-F200-G-MB
RI-F200-B-C / RI-F200-G-C
RI-F200 Instrucon Manual
X 4
RTU
Pulse SO
Safety related noficaon, symbols and instrucons that appear in this
operang manual or on the equipment must be strictly followed to
ensure the safety of personnel as well as the instrument. If the
equipment is not used in a manner specified by the manufacturer it may
impair the protecon provided by the equipment
· Do not use the equipment if there are mechanical damage
· Do not exceed the stated maximum rangs of the device
· No repairs, maintenance or adjustments are possible
· Read the complete instrucon manual prior to installaon or
operang the unit
· The equipment in its installed state must not come into close
proximity to any heang sources, oils, steam, causc vapours or
other unwanted process by-products
· Do not use in hazardous or classified locaon where explosion or
other dangers can be triggered by the device
PRODUCT SAFETY INSTALLATION PRECAUTIONS
Risk of electric shock!
Only to be installed by a competent person
· To prevent the risk of electrocuon, always isolate and lock-off the
power supply to the equipment prior to undertaking any work
· Always confirm absence of electricity prior to starng work using
appropriate voltage detecon equipment
· Wiring shall be done strictly according to the terminal layout
· Confirm that all connecons are correct before energizing the
equipment
· Roung of cables shall be way from any internal EMI source
· Copper cable should be used
· All wiring to be in accordance with applicable local standards
Specificaons Accuracy
Wiring Input 3Ø 4 wire, 3Ø 3 wire, 2Ø 3 wire, 1Ø 2 wire Voltage V L-N and V L-L ±0.5% of full scale
Rated Input Voltage 3x 11...300V AC (L-N), 19...519V AC (L-L) Current ±0.5% of full scale
Frequency Range 45...65Hz Frequency for L-N > 20V, L-L > 35V ±0.1% of full scale
CT Primary 1A/5A...10,000A configurable Acve, Reacve and Apparent Power 1%
CT Secondary 1A or 5A (max rang x1.2) Power Factor ±0.01 of Unity
VT Primary 100...500kV configurable Acve Energy Class 1 (IEC/EN 62053-21)
VT Secondary 100...500V AC (L-L) configurable Reacve Energy Class 2 (IEC/EN 62053-23)
Auxiliary / Power consumpon 100...240V AC (±15%) 45...65Hz / < 8VA
Display Update Rate 1 sec all parameters
Operang / Storage Temperature -10…55°C / -20…70°C Wh Resoluon and Default Pulse Weight
Humidity 0...85% non-condensing
Example
If CT = 100/5A (CT rao = 20) & VT = 350/350V (VT Rao = 1)
Wh resoluon = 0.1kWh (20 x 1 = <150) | Pulse O/P default = 0.1kWh/pulse
Protecon Degree (IEC/EN60529) IP54 Front only (rubber gasket fied)
Pulse Output External 5...27V DC / 100mA max
Pulse Resoluon / Duraon 0.01...99.99kWh per imp / 0.1...2 sec
Communicaon Modbus RTU over RS485
MBus (EN13757)
CT Rao x VT Rao <15 <150 <1500 <15k <150k
Wh / VArh / VAh 0.01k 0.1k 1k 0.01M 0.1M
>150k
1M
INT 0.01k 0.1k 1k 0.01M 0.1M 0.1M
MECHANICAL INSTALLATION
EO&E: Document subject to change
Installaon & Environmental
Panel mounted, indoor used only.
Installaon category: III (300V L-N)
Altude: up to 2000 m
Protecon Class: II
Polluon degree: II
All terminal covers must be fied aer wiring

RI-F200-IM-V01
2
WIRING
Modbus / MBus
Wiring Topology
Daisy Chain Star Network
Modbus ü û
MBus ü ü
A | B
+ | -
1 | 2
Typical Modbus
configuraon shown
For MBus interface
follow Wiring
Topology below
500m Max, ≤ 32 meters
Fuse class CC UL / fast acng 600V
Rang 0.5A
For ’Volt-free’ PLC or digital input,
voltage must be provided by the addion
of a DC PSU
Single Core
0.5 > 4mm2
Ø 2.5mm max
Stranded
0.5 > 2.5mm2 +
7mm
Ø 2.5 mm
0.8 Nm
Max
3P4W
3 CTs
1P2W
1 CT
2P3W
2 CTs
2 VTs
2P3W
2 CTs
3P3W
2 CTs
2 VTs
3P3W
2 CTs
3P4W
3 CTs
3 VTs
Voltage
and current
must be
from same
phase

RI-F200-IM-V01
3
F200-x-C
F200-x-MB
Seng Default Adjustment Range Network
& CT
Must
configure
VT
Adjust if
Using VT
Comms
Modbus /
MBus
Pulse O/P
Adjust if
ulised
System
Sengs
Oponal
1 1 Change Password 1000 NO / YES (0000 - 9998) ü
2 2 Phase Network Selecon 3P4W 3P4W
3P3W
1P2W-P1
ü
3 3 CT Secondary (see CT Label) 5 1A / 5A ü
4 4 CT Primary (see CT Label) 5 1A/5A > 10000A ü
5 5 PT Secondary 350 100V > 500V ü
6 6 PT Primary 350 100V > 500kV ü
7 7 Slave ID Modbus:
MBus (Primary ID):
1
1
1 > 255
1 > 250 ü
8 8 Baud rate Modbus:
MBus:
9600
2400
300 > 19200 bps
1200 > 9600 ü
9 9 Parity Modbus:
MBus:
None
Even
None / Odd / Even
Even ü
10 10 Stop Bit Modbus:
MBus:
1
1
1 / 2
1 ü
11 11 Back Light Off (0000 = Never) 0000 0 > 7200 Sec ü
12 12 Demand interval method Sliding Sliding / Fixed ü
13 13 Demand interval duraon 15 1 > 30 ü
14 14 Demand interval length 1 1 > 30 min ü
15 15 Max Auto Display Pages 21 1 > 21 ü
16 16 Change Page Sequence 1 > 21 No / YES (1 > 21) ü
17 17 Pulse Weight 0.01 00.01 > 99.99 kWh/imp ü
18 18 Pulse Duraon 0.1 0.1 > 2.0 Sec ü
X 19 MBus Secondary ID Serial # 0000 0000 > 9999 9999 ü
19 20 Factory Default No No / Yes Does not reset energy & demand values ü
20 21 Reset Energy No No / Yes (Password +1) ü Once entered, reset each value individually
21 22 Reset Demand No No / Yes ü
22 23 Reset Auxiliary Switch ON No No / Yes ü
CONFIGURATION
Step A: Enter Configuraon Menu Step B: Configure each seng, as required, referring to
Sengs Table below, using the buons as follow:
1 Press either buon once to make digit or opon flash,
press again to move flashing cursor
2 Press to change digit or opon, press or
to move cursor posion as required
3 Press to save and move to next seng opon, Exit
menu once all sengs are configured (see Step 1)
Hold 3 Secs to
Enter Config
(same to Exit)
Password = 1000
(Refer to Step 2)
2
1

RI-F200-IM-V01
4
OPERATION
1 Current level bar graph (% of CT current rang)
2 Funcons & displayed measurement indicators:
RS485 communicaon in progress
Integraon of energy (blinks every 5 sec)
∑ Sum of 3-phase
AVG Average of 3-phase
DMD Max/Min Demand
TH Total Harmonic Distoron (THD)
IP Imported Energy (posive value)
EP Exported Energy (negave value)
Total Sum of 3-phase Energy (IP or EP)
Net Sum of IP + EP Energy
3 Funcon buons and funcon symbols
4 Phase & total or average instantaneous measurements
(V, A, PF, Hz, kW, kVAr, kVA) >> V/I/VAF/PF/P buons
5 Energy readings (kWh/kVArh/kVAh) >> E buon
Voltage Phase Sequence
Hold 3 sec
OK-CLK: L1 → L2 → L3
ANTI-CK: Incorrect Order
INVAL Id: Missing Phase û
ü
Rayleigh Instruments Limited (Head Office)
Raytel House, Cutlers Road, South Woodham Ferrers, Chelmsford, Essex. CM3 5WA
W: www.rayleigh.com E: [e-mail]
Rayleigh Instruments Limited SP. Z o.o. (European Office)
Ul. Aleje Jerozolimskie 214, Warsaw, Poland, 02-486
W: www.rayleigh.pl E: [e-mail]
E
x1 > 9 Acve Energy - kWh L1 IP L2 IP L3 IP L1 EP L2 EP L3 EP ∑ IP ∑ EP Net (IP + EP)
x10 > 18 Reacve Energy - kVArh L1 IP L2 IP L3 IP L1 EP L2 EP L3 EP ∑ IP ∑ EP Net (IP + EP)
x19 > 22 Apparent Energy - kVAh L1 L2 L3 ∑ Hold 10 sec - change Page Scroll
E Auto <-> Manual
x23 > 24 Run Hour (0.01 hr = 36 sec) Number of Auxiliary Switch ON
No. of
Presses V I VAF PF P
x1 Voltage (L-N) Current L1: V/A/PF/Hz Power Factor Acve Power - kW
x2 Voltage (L-L) Current Max DMD L2: V/A/PF/Hz
Hold 10 sec
displays Serial #
Reacve Power - kVAr
x3 % THD (L-N) % THD L3: V/A/PF/Hz Apparent Power - kVA
x4 % THD (L-L) Avg: V/A/PF/Hz L1: kW/kVAr/kVA/PF
x5 L2: kW/kVAr/kVA/PF
x6 L3: kW/kVAr/kVA/PF
x7 ∑: kW/kVAr/kVA/PF
x8 Max DMD: kW/kVAr/kVA
x9 Min DMD: kW/kVAr
Hold 10 sec
Reverse Indicaon
0 = None
1, 2 or 3 = Reversed 1. L-N parameters are not
displayed For 3P3W
2. Parameters in BOLD not
displayed for 1P2W