Raymarine ST70 Instrument User manual

ST70 Autopilot
Controller
Installation Guide
Document reference: 87071-1
Date: 17th March 2007
87071-1.book Page i Monday, April 21, 2008 3:34 PM

ii
87071-1.book Page ii Monday, April 21, 2008 3:34 PM

iii
Contents
Chapter 1:Before you begin ............................................................................. 1
1.1 Installation overview .............................................................................. 1
1.2 Certified installation ............................................................................... 1
1.3 Further assistance ................................................................................. 1
1.4 Product documents ................................................................................ 2
Chapter 2:Planning ............................................................................................ 3
2.1 System overviews .................................................................................. 3
2.2 Positioning the ST70 autopilot controller ................................................ 5
2.3 Parts supplied ........................................................................................ 7
2.4 Parts not supplied .................................................................................. 8
Chapter 3:Installation ....................................................................................... 9
3.1 To install the autopilot controller ............................................................. 9
3.2 Commissioning .................................................................................... 13
Chapter 4:Technical specifications ............................................................ 15
Chapter 5:Templates ....................................................................................... 17
87071-1.book Page iii Monday, April 21, 2008 3:34 PM

iv
87071-1.book Page iv Monday, April 21, 2008 3:34 PM

Preface v
Contents
Preface
Warnings and cautions
As correct performance of the boat’s steering is critical for safety, we STRONGLY
RECOMMEND that an Authorized Raymarine Service Representative fits this
product. You will only receive full warranty benefits if you can show that an Authorized
Raymarine Service Representative has installed or commissioned this product.
Electromagnetic Compatibility (EMC) conformance
Raymarine equipment and accessories conform to the appropriate Electromagnetic
Compatibility (EMC) regulations for use in the recreational marine environment.
Correct installation is required to ensure that EMC performance is not compromised.
Always check the installation before going to sea to make sure that it is not affected by
radio transmissions, engine starting or other forms of interference.
To do this:
1. Turn on all transmitting equipment (radar, VHF radio, etc.).
2. Check that all electronic systems are unaffected by interference from the transmit-
ting equipment.
WARNING: Product installation and operation
This equipment must be installed, commissioned and oper-
ated in accordance with the Raymarine instructions provided.
Failure to do so could result in personal injury, damage to your
boat and/or poor product performance. Before you install the
ST70 autopilot controller, check that individual components
are the correct voltage for your boat’s supply.
WARNING: Electrical safety
Make sure you have switched off the power supply before you
start installing this product.
WARNING: Navigational safety
Although we have designed this product to be accurate and
reliable, many factors can affect its performance. Therefore, it
should serve only as an aid to navigation and should never
replace commonsense and navigational judgement. Always
maintain a permanent watch so you can respond to situations
as they develop.
87071-1.book Page v Monday, April 21, 2008 3:34 PM

vi
EMC installation guidelines
Raymarine equipment and accessories conform to the appropriate Electromagnetic
Compatibility (EMC) regulations. This minimizes electromagnetic interference
between equipment, which could otherwise affect the performance of your system.
Correct installation is required to ensure that EMC performance is not compromised.
For optimum EMC performance, we make the following recommendations:
• Place Raymarine equipment and cables at least 3 ft (1 m) from any equipment that
transmits, or cables that carry, radio signals from VHF radios, cables and anten-
nas. In the case of SSB radios, the distance should be increased to 7 ft. (2 m).
• Place Raymarine equipment and cables more than 7 ft (2 m) from the path of a
radar beam. A radar beam can normally be assumed to spread 20 degrees above
and below the radiating element.
• Use a power source separate from that used for engine-start. This is important to
prevent erratic behavior and data loss which can occur if the engine-start does not
have a separate battery.
• Use Raymarine-specified cables.
• Do not cut or extend cables unless doing so is detailed in the installation manual.
Remember
Where constraints on the installation prevent any of the above recommendations:
• Always allow the maximum separation possible between different items of electri-
cal equipment.
This will provide the best conditions for good EMC performance of the installation.
Suppression ferrites
Raymarine cables may be fitted with suppression ferrites. These are necessary for
correct EMC performance. Any ferrite removed during installation must be replaced
as soon as installation is complete.
Use only ferrites of the correct type, supplied by Raymarine authorized dealers.
Connections to other equipment
If Raymarine equipment is to be connected to other equipment using a cable not
supplied by Raymarine, a Raymarine suppression ferrite MUST always be attached
to the cable near the Raymarine unit.
EMC Servicing and maintenance
• Undue noise and interference may be a symptom of an EMC-related problem.
Please report any EMC-related problem to your nearest Raymarine dealer. We
use such information to improve our quality standards.
• To minimize any EMC related problems and ensure the best possible perfor-
mance form your Raymarine equipment, follow the guidelines given in the instal-
lation instructions.
87071-1.book Page vi Monday, April 21, 2008 3:34 PM

Preface vii
Product disposal
Waste Electrical and Electronic (WEEE) Directive
The WEEE Directive requires the recycling of waste electrical and electronic
equipment.
Whilst the WEEE Directive does not apply to some of Raymarine's products,
we support its policy and ask you to be aware of how to dispose of this product.
The crossed out wheelie bin symbol, illustrated above, and found on our products
signifies that this product should not be disposed of in general waste or landfill.
Please contact your local dealer, national distributor or Raymarine Technical Services
for information on product disposal.
87071-1.book Page vii Monday, April 21, 2008 3:34 PM

viii
87071-1.book Page viii Monday, April 21, 2008 3:34 PM

Chapter 1: Before you begin 1
Chapter 1: Before you begin
The ST70 Autopilot controller is the interface to your autopilot system. It must be
installed correctly following the instructions in this guide. For a safe and successful
installation, we recommend a certified installation.
1.1 Installation overview
The key steps in the procedure are as follows:
Planning
1. Plan your system.
2. Decide where to locate the ST70 autopilot controller.
3. Check parts.
Installing
1. Fit ST70 cable to SeaTalk or SeaTalkng system.
2. Cut required holes.
3. Connect the controller.
4. Test the system.
5. Secure the controller in position.
1.2 Certified installation
Raymarine recommends certified installation by a Raymarine approved installer. A
certified installation qualifies for enhanced warranty benefits. Contact your
Raymarine dealer for further details and refer to the separate warranty card packed
with your product.
1.3 Further assistance
Comprehensive customer support is available online and by telephone.
www.raymarine.com
In the Customer Service area you will find:
• Frequently Asked Questions (FAQs).
• Servicing information.
• Email access to the Raymarine Technical Support Department.
• Details of Raymarine agents worldwide.
Telephone helpline
In the USA
[phone] extension 2444
In the UK, Europe, the Middle East or the Far East
[phone] (voice)
[phone] (fax)
87071-1.book Page 1 Monday, April 21, 2008 3:34 PM

2
Help us to help you
When requesting service, please quote as much of the following product information
as possible:
•Producttype
• Model number
• Serial number
• Software issue number
1.4 Product documents
The following documents are available from www.raymarine.com/handbooks to
help you install and operate the ST70 autopilot controller:
To the best of our knowledge, the information in the product documents was correct
when they went to press. However, Raymarine cannot accept liability for any
inaccuracies or omissions in product documents.
In addition, our policy of continuous product improvement may change specifications
without notice. Therefore, Raymarine cannot accept liability for any differences
between the product and the accompanying documents.
Document Part number
ST70 Autopilot Controller Installation Guide (this
document).
87071-1
SPX System Commissioning Instructions (supplied
with the ST70 autopilot controller). Following installa-
tion of the ST70 controller, you must use these instruc-
tions to commission your autopilot system before it can
be used safely.
81287-1
SPX System Installation Guide. Instructions for
installing an autopilot system based around the SPX
SmartPilot computer.
87072-1
SeaTalkng Reference Manual. This provides detailed
information regarding SeaTalkng connectivity.
81300-1
Autopilot Operating Guide (supplied with the ST70
autopilot controller).
81289-1
Product installation guides. Separate installation
sheets are provided with individual components of the
autopilot system including the compass, rudder refer-
ence sensor and drive
87071-1.book Page 2 Monday, April 21, 2008 3:34 PM

Chapter 2: Planning 3
Chapter 2: Planning
2.1 System overviews
The ST70 autopilot controller is connected to the boat’s data system, which could be
SeaTalkng or SeaTalk.
SeaTalk
ng
The diagram below shows how the ST70 controller fits into a typical SeaTalkng
system.
Typical Seatalk
ng
system with autopilot
D10433-1
Course Computer
SeaTalkng backbone
SeaTalkng spur
SeaTalkng backbone
Wind
transducer
Transducer pod
Transducer
pod
Depth
transducer
Speed
transducer
Transducer
pod
ST70 instrumentsST70 controller
12V dc
Power Supply
SMARTPILOT
Drive unit
87071-1.book Page 3 Monday, April 21, 2008 3:34 PM

4
SeaTalk
ng
system structures and load limitations
There are restrictions on cable lengths, power location and the number of
components you may connect to a SeaTalkng system. For complete information on
SeaTalkng connectivity, refer to the SeaTalkng Reference Manual supplied with the
SeaTalkng Backbone Kit. See page 8 for information about additional SeaTalkng cables
and accessories, including the SeaTalkng backbone kit.
SeaTalk
In a typical SeaTalk system, the ST70 autopilot controller is connected to an existing
instrument on the SeaTalk system using a SeaTalkng-to-SeaTalk adapter cable.
Typical SeaTalk system with autopilot
Note: You cannot callibrate an S1, S2 or S3 SmartPilot computer with an ST70 autopilot con-
troller, you must use a SmartPilot controller.
Depth
transducer
Course
computer
ST70 controller
SeaTalkng to SeaTalk
adaptor cable
SeaTalk cable
ST60+ speed
instrument
ST60+ wind
instrument
Speed
transducer
D10398-1
Wind
transducer
12V dc
SeaTalk
cable
SeaTalk
cable
ST6002 controller
87071-1.book Page 4 Monday, April 21, 2008 3:34 PM

Chapter 2: Planning 5
2.2 Positioning the ST70 autopilot controller
CAUTION: The autopilot controller must be placed a safe distance from
equipment that could adversely effect its performance. Refer to the EMC
guidelines on.
• There must be sufficient space to mount the autopilot controller.
• There should be no obstacles between the user and the autopilot controller.
• The connection point should be within 400mm of the install location (unless you
are using an extension cable). In a SeaTalkng network, the connection point will be
a T-piece or connector block on the backbone cable, or another ST70 instrument;
on SeaTalk, the connection point will be an existing instrument, or a connector
block on the system.
• Any holes cut to mount the instrument must not compromise the vessel’s struc-
ture.
Site requirements
D10519-1
Min 0.8m (2ft 6in)
Check
Check
87071-1.book Page 5 Monday, April 21, 2008 3:34 PM

6
The diagram below shows dimension measurements for the ST70 controller.
D10400-1
ST70 dimensions
24 mm
(0.95 in)
24 mm
(0.95 in)
6.5 mm
(0.25 in)
Surface
mount
Flush
mount
110 mm (4.33 in)
104 mm (4.1 in)
115 mm (4.53 in)
90 mm (3.54 in)
87071-1.book Page 6 Monday, April 21, 2008 3:34 PM

Chapter 2: Planning 7
2.3 Parts supplied
DXXXX-1
ST70 autopilot controller
Panel seal
Stud (x 4) SeaTalkng blanking plug (x 1)
Finger nut (x 4)
Sun cover
Mounting bracket
SeaTalkng to SeaTalk 400 mm cable
SeaTalkng 400 mm cable
87071-1.book Page 7 Monday, April 21, 2008 3:34 PM

8
2.4 Parts not supplied
The ST70 autopilot controller is connected to a SeaTalk or SeaTalkng data system. To
install the controller to your system correctly, you may require additional cables and
connectors.
Optional cabling and connectors
Depending on the location of your ST70 autopilot controller, you may require a longer
cable to connect it to the SeaTalkng backbone cable.The backbone cable is supplied
as part of a standard kit. Detailed information on SeaTalkng connectivity is available in
the SeaTalkng Reference Manual supplied with the SeaTalkng backbone kit. For
further information, talk to you dealer or visit the Raymarine website:
www.raymarine.com.
D10420-1
Spur cable
Backbone kit
Part number
A25062
A06038 - 1 ft 3 in (400 mm)
A06039 - 3 ft 3 in (1 m)
A06040 - 9 ft 10 in (3 m)
A06041 - 16 ft 4 in (5 m)
Backbone cable -
16 ft 4 in (5 m), (x 2)
65 ft 7 in (20 m)
T piece, (x 4)
Backbone terminator, (x 2)
Power cable
87071-1.book Page 8 Monday, April 21, 2008 3:34 PM

Chapter 3: Installation 9
Chapter 3: Installation
Read Chapter 1 of this book before you continue. This will help you to:
• Identify the correct installation location and appropriate network connection point.
• Obtain the appropriate tools and connecting cables.
CAUTION: For safety reasons your boat must be at dockside before
commencing installation.
3.1 To install the autopilot controller
Once you are certain it is safe to proceed, carry out the installation tasks listed below
in order.
1. Fit cable to system connection point and route to ST70 controller location
SeaTalkng systems:
• Label both ends of the SeaTalkng cable, and attach it to the backbone or an
existing ST70 instrument on your system.
• Route the cable to the location where you plan to mount the ST70 controller.
WARNING: Electrical safety
Before you make any electrical connections, ensure the power
supply is switched off and you have read the EMC installation
guidelines (see
page 4 ).
D10419-1
ST70 controller ST70 controller ST70 instrument
SeaTalkng T piece SeaTalkng T piece
SeaTalkng backboneSeaTalkng backbone
SeaTalkng spurSeaTalkng spurSeaTalkng spur
87071-1.book Page 9 Monday, April 21, 2008 3:34 PM

10
SeaTalk systems:
• Label both ends of the SeaTalkng-to-SeaTalk adaptor cable, and attach it to an
existing instrument or connect it to a connector block on the system.
• Route the cable to the location in which you plan to mount the ST70 controller.
Note: Check that the cable reaches the required location. If you wish to place the ST70 control-
ler further than 400mm from the connection point you will need to purchase an appropriate
SeaTalkng or SeaTalkng-to-SeaTalk cable.
2. Cut mounting holes
• Use the appropriate flush- or surface-mount template to cut the mounting slot for
the autopilot controller and to drill holes for the fixing screws. See the back of this
book for templates.
• Clean and de-burr the mounting surface
ST70 controller
ST60+ instrument
D10421-1
SeaTalk cable
SeaTalk cable
SeaTalk 3 way block
SeaTalk cable
ST70 controller
ST60+ instrument
SeaTalkng to SeaTalk cable SeaTalkng to
SeaTalk cable
87071-1.book Page 10 Monday, April 21, 2008 3:34 PM

Chapter 3: Installation 11
3. Fit gaskets and brackets
Note: Stick the self-adhesive side of the gasket to the instrument, NOT to the mounting location.
Surface mounting
D10404-1
self adhesive
side
87071-1.book Page 11 Monday, April 21, 2008 3:34 PM

12
Flush mounting
D10403-1
self adhesive
side
87071-1.book Page 12 Monday, April 21, 2008 3:34 PM