Razor FLASHRIDER 360 User manual

OWNER’S MANUAL
Read and understand this entire manual before allowing
child to use this product! For assistance contact Razor.
DO NOT RETURN TO STORE.
NOTE: Manual illustrations are for demonstration purposes only.
Illustrations may not reflect exact appearance of actual product.
Specifications subject to change without notice.
Please have your 21 character product I.D. code ready before contacting Razor for
warranty assistance and/or replacement parts.
Product I.D. Code: _____________ - ____________ - ____________
FLASHRIDER™360°
US_130724

1
SAFETY WARNINGS
CONTENTS
CONTENTS
The recommended rider age of 6 and older for FlashRider 360˚ Caster Trike is
only an estimate, and can be affected by the rider’s size, weight or skills. Any
rider unable to fit comfortably on the FlashRider 360˚ Caster Trike should not
attempt to ride it. A parent’s decision to allow his or her child to ride
this product should be based on the child’s maturity, skill and ability
to follow rules.
Keep this product away from children under the age of 6 and remember that
this product is intended for use only by persons who are, at a minimum,
completely comfortable and competent while operating the FlashRider 360°
and who understand the risks presented by such products.
DO NOT EXCEED THE WEIGHT LIMIT OF 160 LB (73 KG).
Rider weight does not necessarily mean a person’s size is appropriate to fit or
maintain control of the FlashRider 360˚ Caster Trike.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations which may affect the
locations where the FlashRider 360˚ Caster Trike may be used on public
property. The FlashRider 360˚ Caster Trike is meant to be used only in
controlled environments, free of potential traffic hazards and not on public
streets. Do not ride your FlashRider 360˚ Caster Trike in any areas where
pedestrian or vehicle traffic is present.
Ride defensively. Watch out for potential obstacles that could force you to
swerve suddenly or lose control. Be careful to avoid pedestrians, skaters,
skateboards, scooters, bikes, children or animals who may enter your path,
and respect the rights and property of others.
Maintain a hold on the handlebars at all times.
Never carry passengers or allow more than one person at a time to ride the
FlashRider 360˚ Caster Trike.
Never use near streets, swimming pools, hills, steps, or sloped driveways.
Never use headphones or a cell phone when riding.
Never hitch a ride with another vehicle.
The FlashRider 360˚ Caster Trike is intended for use on solid, flat, clean and
dry surfaces, such as pavement or level ground, without loose debris, such as
rocks or gravel. Wet, slick or uneven and rough surfaces may impair traction
and contribute to possible accidents. Do not ride the FlashRider 360˚ Caster
Trike in mud, ice, puddles or water. Avoid excessive speeds that can be
associated with downhill rides. Never risk damaging surfaces, such as carpet
or flooring, by use of a FlashRider 360˚ Caster Trike indoors.
Do not ride at night or when visibility is impaired.
PROPER RIDING ATTIRE
Riders should always wear a properly fitted helmet that complies with U.S.
Consumer Safety Commission (CPSC) Standard 16 CFR 1203. A helmet may be
legally required by local law or regulation in your area. Elbow and kneepads,
long sleeved shirt and long pants are recommended. Always wear closed
toed shoes, keep shoelaces tied and out of the way of the wheels. Never ride
barefooted or in sandals.
FAILURE TO USE COMMON SENSE AND HEED THE
ABOVE WARNINGS INCREASES RISK OF SERIOUS
INJURY. USE WITH APPROPRIATE CAUTION AND
SERIOUS ATTENTION TO SAFE OPERATION.
Parts Breakdown.............................................................................................. 6
Safety Reminders............................................................................................. 7
Warranty .......................................................................................................... 7
WARNING: Riding the FlashRider™360˚ Caster Trike can be a
hazardous activity. Certain conditions may cause the equipment to fail without
fault of the manufacturer. The FlashRider 360˚ Caster Trike can and is intended
to move, and it is therefore possible to lose control, fall off and/or get into
dangerous situations that no amount of care, instruction or expertise can
eliminate. If such things occur you can be seriously injured or die, even when
using safety equipment and other precautions. RIDE AT YOUR OWN RISK AND
USE COMMON SENSE.
This manual contains many warnings and cautions concerning the
consequences of failing to maintain, inspect or properly use your FlashRider
360˚ Caster Trike. Because any incident can result in serious injury or even
death, we do not repeat the warning of potential serious injury or death each
time such a possibility is mentioned.
APPROPRIATE RIDER USE AND
PARENTAL SUPERVISION
This manual contains important safety information. It is your responsibility to
review this information and make sure that all riders understand all warnings,
cautions, instructions and safety topics, and assure that young riders are
able to safely and responsibly use this product. Razor recommends that you
periodically review and reinforce the information in this manual with younger
riders, and that you inspect and maintain your child’s FlashRider 360° to
insure their safety.
Safety Warnings .............................................................................................. 1
Before You Begin.............................................................................................. 2
Assembly and Set-Up....................................................................................3-5
Set-Up and Usage Instructions........................................................................ 5
WARNING: SPARKS CAN INDUCE FIRE
To reduce the risk of SERIOUS INJURY or FIRE:
PARENTS and RIDERS: Make sure riders understand that sparks can
start a fire. Keep sparks away from flammable or combustible substances.
Use only under close adult supervision.
BE RESPONSIBLE: Safety is important. Parents must review the
following warnings and instructions with each rider:
• Never use your caster trike to try to start a fire. Your caster trike
emits localized sparks when the Spark Bar on a moving trike comes in
contact with hardened outdoor surfaces, like asphalt or concrete. Be
responsible.
• For outdoor use only on solid, clean, dry hardened surfaces. Keep
sparks away from substances that can catch fire, such as dry
vegetation, paper, chemicals or gasoline. Sparks can induce fire.
• Do not use in any area prone to wildfires or posted by fire authorities as
a Fire Hazard Zone.
• Do not ride at night.
• Keep sparks away from eyes, hair, exposed skin and clothing. Sparks
can burn.
• Pull up on the Spark Handle to operate sparking feature. NEVER push
down directly on the Spark Bar, spark cartridge or its cover itself.
• Spark Bar gets hot during use. Do not touch after use.
Observe all other spark safety warnings and instructions as provided
elsewhere in this manual.

2
Need Help? Visit our website for replacement parts and product support at www.razor.com or call toll-free at
866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time. Please have the product I.D. code (located on the
bottom of the frame) available for better assistance.
BEFOREYOU BEGIN
Remove contents from box and check parts against parts diagram found on page 6. Remove the separators that
protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint or
dents that may have occurred during shipping. Because the FlashRider 360˚ was partially assembled and packed at the
factory there should not be any problems, even if the box has a few scars or dents.
q Estimated Assembly and Set-Up Time
Allow up to 15–20 minutes for assembly.
WARNING: DO NOT USE
NON-RAZOR PRODUCTS WITH
YOUR FLASHRIDER 360˚.
The FlashRider 360˚ has been
built to certain Razor design
specifications. The original
equipment supplied at the time of
sale was selected on the basis of
its compatibility with the frame,
fork and all other parts. Certain
aftermarket products may be
compatible and will void your
warranty.
q Required Tools
Two (2) 5 mm
Allen wrenches
(included)
10 mm and 13 mm
wrench
(included)
PRODUCT I.D. CODE
1. Bottom of Frame
2. UPC Side of Box (not shown)
Front Fork Assembly
Front Wheel Assembly Steering Bolt
Seat
Barcode
Location
Rear Caster Wheels
Spark Bar
Spark Cartridge
Spark Handle
Spark Cartridge Cover

3
Need Help? Visit our website for replacement parts and product support at www.razor.com or call toll-free at
866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time. Please have the product I.D. code (located on the
bottom of the frame) available for better assistance.
ASSEMBLY AND SET-UP
q Attaching the Spark Bar
Required Tools: 10 mm wrench and 5 mm Allen wrench
1Using two (2) 5 mm Allen
wrenches, remove the coupling
bolt on the end of the frame and
discard the plastic insert. Remove
the coupling bolt in the middle of
the frame.
Note: This coupling bolt is shorter.
1Using a 10 mm wrench and a
5 mm Allen wrench, remove the
coupling bolts from the Spark
Handle.
2Insert the rear frame into the
frame assembly. Securely tighten
the coupling bolt on the rear
frame using two (2) 5 mm Allen
wrenches.
3Securely tighten the coupling
bolt in the middle of the frame
using two (2) 5 mm Allen
wrenches.
2Insert the Spark Handle (right
side) and the Spark Bar (left side)
into the spring mechanism. Align
the holes on the Spark Bar with
the hole on the spring mechanism
and tighten the coupling bolt with
a 10 mm wrench and a 5 mm Allen
wrench.
3Align the holes on the Spark
Handle with the holes on the
Spark Bar and tighten the coupling
bolts with a 10 mm wrench and a
5 mm Allen wrench.
q Attaching the Frame
Required Tools: Two (2) 5 mm Allen wrenches

4
ASSEMBLY AND SET-UP
1Remove the steering bolt and
locknut from the frame assembly
with a 13 mm wrench and a 5 mm
Allen wrench.
2Insert the front fork into the
frame assembly.
q Attaching the Front Fork
Required Tools: 13 mm wrench and 5 mm Allen wrench
4Reinsert the steering bolt and
secure with locknut using a 13 mm
wrench and a 5 mm Allen wrench.
3Be sure to properly align the
slot on the headtube with the pin
on the front fork as shown.
1Remove the four (4) coupling
bolts from the front fork using a
5 mm Allen wrench and a 10 mm
wrench.
2Insert the wheel assembly into
the front fork and align holes.
When installing the wheel, make
sure the letter “F” and arrow
(located on the side of the wheel)
are facing the direction as shown
above.
q Attaching the Front Wheel
Required Tools: 5 mm Allen wrench and 10 mm wrench
WARNING: Failing
to properly tighten the steering
bolt that attaches the front fork
assembly to the frame assembly can
cause you to lose control and fall.
3 Reinsert the coupling bolts
through the front fork and tighten
securely.

5
2Place new cartridge in back of the bracket making sure to align the slots
on the cartridge with the two legs of the bracket. Slide the cartridge forward
until you hear a click and the thumb tabs are locked in place.
1Using your thumbs, press tabs
on both sides of the cartridge to
release from the bracket. Slide
the cartridge away from you and
remove from bracket.
q Using the Spark Handle WARNING: Pulling
the Spark Handle upwards too
strenuously may cause loss of
control.
NOTE: Sparks and Spark
cartridge life will vary based on
the amount of pressure applied
by Spark Handle, the length of
time pressure is applied and
the smoothness of the riding
surface.
WARNING: Do not
attempt to replace the cartridge
immediately after riding as cartridge
will be hot. Handle only when cool.
WARNING: Keep fingers
clear of Spark Bar hinge.
q Replacing the Spark Cartridge:
Friction during sparking will eventually wear out the replaceable cartridge and cause the trike to stop making sparks.
Worn out cartridges should be replaced.
1 Pull back on the Spark Handle to operate
sparking feature.
NEVER push down directly on the Spark Bar, Spark
Cartridge or Spark Cartridge Cover itself.
1Using two (2) 5 mm Allen
wrenches, remove the four (4)
coupling bolts from the frame.
2Align the four (4) holes in seat
with the four (4) holes in frame.
Insert the coupling bolts through
the top and bottom of the frame.
q Attaching the Seat
Required Tools: (2) 5 mm Allen wrench
3 Tighten the coupling bolts using
two (2) 5 mm Allen wrenches.
ASSEMBLY AND SET-UP
SET-UP AND USAGE INSTRUCTIONS

6-4
4-1
2
2-1
5
1
3
4
87-1
7
9
11
10
6-1
6
6-2
6-3
6-5
6
Need Help? Visit our website for replacement parts and product support at www.razor.com or call toll-free at
866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time. Please have the product I.D. code (located on the
bottom of the frame) available for better assistance.
FLASHRIDER 360° CASTER TRIKE PARTS
Keep your FlashRider 360˚ rolling for years with genuine Razor parts. Visit our website to purchase replacement parts.
(Specifications subject to change without notice.)
1 Handlebar Grip (x2)
2 Front Fork
2-1 Front Fork Coupling Bolts (x4)
3 Front Cover
4 Steering Bolt
4-1 Lock Nut
5 Front Wheel w/ Pedals and Cranks Complete
6 Rear Wheel Assembly (x2)
6-1 Rear Wheel Cover
6-2 Spring Washer
6-3 Caster
6-4 Axle Bolts
6-5 Wheel
7 Seat
7-1 Seat Coupling Bolts (x4)
8 Spark Handle
9 Spark Bar
10 Spark Cartridge
11 Spark Cartridge Cover

7
SAFETY REMINDERS
Need Help? Visit our website for replacement parts and product support at www.razor.com or call toll-free at
866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time. Please have the product I.D. code (located on the
bottom of the frame) available for better assistance.
DO NOT RETURNTO STORE
Failure to follow these instructions may damage
your product and void your warranty.
Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing defects
for a period of six (6) months from date of purchase. This Limited Warranty
does not cover normal wear and tear, or any damage, failure or loss caused by
improper assembly, maintenance, storage or use of the Razor FlashRider 360˚.
This Limited Warranty will be void if the product is ever
•usedinamannerotherthanforrecreation;
•modiedinanyway;
•rented.
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
Razor does not offer an extended warranty. If you have purchased an extended
warranty, it must be honored by the store at which it was purchased.
For your records, save your original sales receipt with this manual.
_______________________________________________________
Loose Parts
Check and secure all fasteners before every ride. Make sure the
steering bolt and casters are tight. There should not be any unusual
rattles or sounds from loose parts or broken components. If you are
not sure, ask an experienced mechanic to check.
Frame, Fork and Handlebars
Check for cracks or broken connections. Although broken frames
are rare, it is possible for an aggressive rider to crash into a curb
or wall, and wreck, bend or break a frame. Get into the habit of
inspecting yours regularly.
q
q q
qWheel Care
Periodically inspect the wheels for excess wear.
Safety Gear
Always wear proper protective equipment, such as an approved
safety helmet. Elbow pads and knee pads are recommended.
Always wear closed toed shoes (lace-up shoes with rubber soles),
never ride barefooted or in sandals, and keep shoe laces tied and
out of the way of the wheels.
PRE-RIDE CHECKLIST
SET-UP AND USAGE INSTRUCTIONS
U.S. Patent No. D593,910 S
Printed in China for:
Razor USA LLC
PO Box 3610
Cerritos, CA 90703
Copyright © 2003-2013 Razor USA, LLC. All rights reserved. RAZOR and the Razor Logo Design
are among the registered trademarks of Razor USA LLC in the United States and/or select
foreign countries. FlashRider is a trademark of Razor USA LLC. US_130724