Horizon Fitness 50400046 User manual

OWNER’S MANUAL
BENUTZERHANDBUCH
GEBRUIKERSHANDLEIDING
MANUEL DU PROPRIÉTAIRE

3 ENGLISH
29 DEUTSCH
55 NEDERLANDS
81 FRANÇAIS

33
INDOOR CYCLE OPERATION
ENGLISH

4
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS EXERCISE EQUIPMENT.
• Keep children off your Bike at all times.
• When the Bike is in use, young children and pets should be kept at least 10 feet away.
• Use this Bike only for its intended use as described in the manual.
• Keep your hands away from all moving parts. Never turn the pedal crank arms by hand.
• Do not remove your feet from the pedals while they are in motion.
• After exercising, push down on the tension knob or turn the tension knob in a clockwise direction to slow the flywheel down
and decrease the potential for injury.
• Do not dismount the Bike until both the pedals and flywheel have come to a complete stop.
• Do not attempt to use this Bike at high speeds or in standing positions until you have practiced and are comfortable at lower
speeds.
• Rotate the tension knob clock wise to add resistance to the flywheel prior to standing on the pedals.
• Never drop or insert any object into any opening on this Bike.
• Do not use without proper footwear.
• Rotate the tension knob clock wise to lock the flywheel when not in use.
To assure that the safety level of this Bike is maintained, examine components for wear and tear on a regular basis.
Components that are worn excessively or inoperable should be replaced immediately or the Bike should be put out of use until
it is repaired.
CAUTION!
If you experience chest pains, nausea,
dizziness or shortness of breath,
stop exercising immediately and
consult your physician before continuing.
This application is only for indoor use at home,
not recommend to use in commercial environment.
ENGLISH

5
2 ft
0.6 m
2 ft
0.6 m
2 ft 0.6 m
2 ft 0.6 m
FREE AREA
TRAINING
AREA
IBKE
HOW TO MOVE THE INDOOR CYCLE
Due to the weight of the Indoor Cycle, it is recommended
that two persons move it. While one person lifts the back
of the indoor cycle, the second person firmly holds the
handlebar and tips the indoor cycle forward until it rolls
on the wheels. Carefully move the Indoor Cycle to the
desired location and then lower it.
If the Indoor Cycle rocks on the floor after being set
down, turn the leveling feet underneath the front or rear
stabilizer until the rocking motion is eliminated.
Leveling Feet
To reduce the risk of injury, use extreme caution
while moving the indoor cycle. Do not attempt to
move it over uneven surfaces and make sure there’s
a safety space of 20 inch (minimum) to the nearest
equipment is recommended.
WARNING
LOCATION OF THE
INDOOR CYCLE
Place the Indoor Cycle on a
level and stable. There should be
2 feet (60 cm) of each side
surround the Indoor Cycle. Do
not place the cycle in any area
that will block any vent or air
openings. The Indoor Cycle
should not be located in a
garage, covered patio, near
water or outdoors.
Firmly grasp the
handlebars, carefully tip
toward you, and roll on the
transport wheels.
A
B
ENGLISH

6
HOW TO ADJUST THE INDOOR CYCLE
The Indoor Cycle can be adjusted for maximum comfort and exercise effectiveness. The instructions below describe one
approach to adjusting the Indoor Cycle to ensure optimal user comfort and ideal body positioning; you may choose to adjust the
Indoor Cycle differently.
SADDLE ADJUSTMENT
Proper saddle height helps ensure maximum
exercise efficiency and comfort, while
reducing the risk of injury. Adjust the saddle
height to make sure it’s in proper position, one
that keeps a slightly bend in your knee while
your legs are in the extended position.
HANDLEBAR ADJUSTMENT
Proper position for the handlebar is based
primarily on comfort. Typically, the handlebar
should be positioned slightly higher than
the saddle for beginning cyclists. Advanced
cyclists could try different heights to get the
arrangement most suitable for you.
A
B
ENGLISH
Model IBKE as a representative for illustration

7
TO ADJUST THE SADDLE HEIGHT:
Rotate the adjustment lever counterclockwise and adjust the saddle to a comfortable pedaling position. Rotate the lever
clockwise to lock saddle position.
TO ADJUST THE SADDLE HORIZONTAL POSITION:
Rotate the adjustment lever counterclockwise to slide the saddle forward or backward as desired. Rotate the lever clockwise to
lock saddle position. Test the saddle slide for proper operation.
ENGLISH

8
TO ADJUST THE HANDLEBAR HEIGHT:
Rotate the adjustment lever counterclockwise to adjust the handlebar height. Raise or lower the handlebar to the desired
height. Rotate the lever clockwise to lock handlebar position.
TO ADJUST THE PEDAL STRAPS:
Place each foot ankle on the pedal and in the toe clip that the foot ankle is centered over the pedal spindle (center of the
pedal). Rotate one foot to arms reach and pull up on the toe clip strap. Repeat for the other foot. Keep your knees over your
feet as you pedal. To remove your foot from the toe clip, loosen the strap and pull out.
The pedal straps should
be adjusted to hold the
foot snugly in the pedal .
ENGLISH

9
RESISTANCE CONTROL AND EMERGENCY BRAKE
The preferred level of difficulty in pedaling (resistance) can be regulated in fine increments by use of the resistance control
lever. To increase the resistance, push down the resistance control lever. To decrease the resistance, pull up the lever.
IMPORTANT:
• To stop the flywheel while pedaling, push down to extremely
on the resistance control lever.
• The flywheel should quickly come to a complete stop.
• Make sure your shoes are fixed into the toe clip.
• Apply full resistance load when the bike is not in use to
prevent injuries due to moving drive gear components.
Resistance control /
Emergency brake
The Indoor Cycle does not have a free moving flywheel; the
pedals will continue to move together with the flywheel until
the flywheel stops. Reducing speed in a controlled manner
is required. To stop the flywheel immediately, push down
to extremely on the resistance control lever. Always pedal
in a controlled manner and adjust your desired cadence
according to your own abilities. Push down extremely the
resistance control lever down = emergency stop.
WARNING
The Indoor Cycle uses a fixed flywheel that builds momentum and will keep the pedals turning even after the user stops pedaling or if
the user’s feet slip off. DO NOT ATTEMPT TO REMOVE YOUR FEET FROM THE PEDALS OR DISMOUNT THE MACHINE UNTIL
BOTH THE PEDALS AND THE FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow these instructions may lead to loss of
control and the potential for serious injury.
WARNING
ENGLISH

10
ENGLISH

1111
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To
prevent damage to the indoor cycle, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your indoor cycle’s serial number located on
the front base frame of the cycle and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
SERIAL NUMBER:
MODEL NAME: JOHNSON INDOOR CYCLE
WARNING
ENGLISH

12
Main Frame
Bottle Holder
Front Stabilizer
Pedal
Handlebar Set
Console
Saddle Set
Rear Stabilizer
Levelers
Model IBKE as a representative for illustration
MODEL INFORMATION
ENGLISH

13
PRE ASSEMBLY
If you have questions or if there
are any missing parts, contact your
local dealer. Contact information
may be located on the back panel
of this manual or on warranty card.
UNPACKING
Due to the weight of the indoor cycle, it is recommended that two persons
perform the assembly. Set the indoor cycle in a cleared area and remove all
packing materials; do not dispose of the packing materials until assembly is
completed.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
NEED HELP?
ENGLISH
MAIN PARTS INCLUDED:
Main Frame
Front & Rear Stabilizer
Handlebar Set
Saddle Set
Pedals
Console
Bottle Holder
Levelers

14
ASSEMBLY STEP 1
ENGLISH
Z06x4
Z01x3
Z05x4
K50x2
Z06x4
Z05x4
K50x2
Z06x3
Z05x3
Torque Value (Z01,Z06) 30 Nm / 22 lb-ft.
IBKE ICR50
WASHER (Z05)
Φ8.2 X Φ15 X 1.2T
QTY: 7
BOLT (Z06)
M8 X 20L
QTY: 7
LEVELER (K50)
QTY: 2
BOLT (Z01)
M8 X 20L
QTY: 3
WASHER (Z05)
Φ8.2 X Φ15 X 1.2T
QTY: 4
BOLT (Z06)
M8 X 20L
QTY: 4
LEVELER (K50)
QTY: 2

15
ASSEMBLY STEP 2
ENGLISH
Torque Value (Z02)
30 Nm / 22 lb-ft.
A Attach HANDLEBAR to the CONSOLE MAST
using 4 x BOLTS (Z02) and fasten by ALLEN
WRENCH. Make sure all bolts are tightened.
Z02
BOLT (Z02)
M8 X 20L
QTY: 4

16
ASSEMBLY STEP 3
ENGLISH
A Release the stem plate cover from the
CONSOLE and Attach CONSOLE to the
HANDELBAR console stem using 4 x BOLTS
(G16).
B Flip the CONSOLE to face the rider position.
Attach the stem plate cover to the CONSOLE
as it was.
G16
1
1
A
BOLT (G16)
M4 X 12L
QTY: 4

17
ASSEMBLY STEP 4
ENGLISH
A Take the CONSOLE power cord from the MAIN
FRAME by direction shown as in the figure and
plug into power input at the CONSOLE.
B Insert the CONSOLE power cord in the console
cord retainers .
C Cut the velcro STRAP (Z08) to the preferred
lengths to attach the rest of power cord to the
HANDELBAR screen stem.
D Flip the CONSOLE slowly to ensure the power
cord remains inserted correctly.
A
B
Z08
C
D
2
STRAP (Z08)
20 X 700L X 2.0T
QTY: 1

18
ASSEMBLY STEP 5
A Remove the 2 x BOLTS from the MAIN
FRAME.
B Attach BOTTLE HOLDER to the MAIN FRAME
using 2 x longer BOLTS (L25).
L25
3
3
ENGLISH
BOLT (L25)
M4 X 10L
QTY: 2

19
ASSEMBLY STEP 6
T03
R
T03
L
A Attach PEDAL (R) to the CRANK in the right
hand side, between CRANK and PEDAL (R), a
WASHER (T03) is necessary. Then tighten the
PEDAL (R) by WRENCH.
B Repeat the assembly process on the left hand
side.
ENGLISH
WASHER (T03)
Φ15 X Φ22 X 3T
QTY: 2

20
ASSEMBLY STEP 7
ASSEMBLY COMPLETE!
Dimension: 140 x 56.5 x 127 cm / 55” x 22” x 50”
Product Weight: 57 kg / 126 lbs.
Max. User Weight: 136 kg / 300 lbs.
ENGLISH