Razor GGC2030M User manual

Outdoor Portable LP Gas Griddle
Model No. GGC2030MModel No. GGC2030M
OWNER’SOWNER’S MANUALMANUAL
Manufactured in China for: RevoAce Inc. Limited
Hong Kong, China • 1.800.694.0013 • [email protected]
8:00 am to 4:00 pm central time, Monday to Friday.
© RevoAce Inc. Limited
Razor®is a registered trademark of Mr. Bar-B-Q Products LLC. Used with permission.
#GriddleOnTM is a trademark of Mr. Bar-B-Q Products LLC. Used with permission.
Make it SizzleTM is a trademark of Mr. Bar-B-Q Products LLC. Used with permission. GGC2030M-E-OM-F101
PATENT PENDING
Table of Contents
Important Safeguards ...........................................................Page 2
Expanded View & Hardware .......................................................... 4
Assembly Instructions............................................................... 5
Griddle Storage & Transporting ....................................................... 7
Installing LP Gas Tank.............................................................. 10
Operating Instructions.............................................................. 10
Cleaning and Care ................................................................ 11
Product Registration ............................................................... 12
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Limited Warranty ................................................................. 12
Troubleshooting .................................................................. 13
The use and installation must conform with local codes or, in the absence of local codes, with either the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, Storage and Handling of Liquefied Petroleum Gases, ANSI/
NFPA 58, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code,
B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV Series, as
applicable.
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
If you are assembling this unit for someone else, give this manual to them to read and save for future
reference.
¸WARNING: This product can expose you to chemicals including carbon
monoxide, soot, lead and lead components which are known to the State
of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
Made from 75% Bagasse
(environmentally friendly sugar
cane pulp by-product)
WARNING
FOR YOUR SAFETY:
For Outdoor Use Only
(outside any enclosure)
DANGER
If you smell gas -
• Shut off gas to appliance.
• Extinguish any open flame.
• Open Lid.
• If odor continues, keep away from the
appliance and immediately call your fire
department.
Failure to follow these instructions could result
in fire or explosion which could cause property
damage, personal injury or death.
WARNING
FOR YOUR SAFETY:
1. Do NOT store or use gasoline or other
flammable liquids or vapors in the vicinity
of this or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
3. Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage.
4. Read the installation, operation, and
maintenance instructions thoroughly
before installing or servicing this
equipment.
DANGER
• Never operate this appliance unattended.
• Never operate this appliance within 10
ft (3.0 m) of any structure, combustible
material or other gas cylinder.
• Never operate this appliance with 25 ft (7.5
m) of any flammable liquid.
• Do not fill cooking vessel beyond maximun
fill line.
• Never allow oil or grease to get hotter than
400°F or 200°C. If the temperature exceeds
400°F ( 200°C) or if oil begins to smoke,
immediately turn the burner or gas supply
OFF.
• Heated liquids remain at scalding
temperatures long after the cooking
process. Never touch cooking appliance
until liquids have cooled to 115°F ( 45°C)
or less.
• If a fire should occur, keep away from the
appliance and immediately call your fire
department. Do not attempt to extinguish
an oil or a greas fire with water.
Failure to follow these instructions could result
in fire, explosion or burn hazzard which could
cause property damage, personal injury or
death.
IMPORTANT
After each use, always season your griddle per “Seasoning
Griddle” section.
WARNING
FOR YOUR SAFETY:
DO NOT LEAVE THIS APPLIANCE UNATTENDED
WHILE IN USE, ESPECIALLY COOKING THE FATTY
MEAT AND CLOSE THE LID TOO LONG TIME.
razorgriddle.com
@razorgriddle
@razorgriddle

Outdoor Portable LP Gas Griddle
Model No. GGC2030M
2
WThis griddle is for outdoor use only, and should not be used in a
building, garage or any other enclosed area.
WDo NOT operate, light or use this appliance within ten feet (3.05 m) of
walls, structures or buildings.
WFor residential use only. This griddle is NOT for commercial use.
WThis griddle is not intended for and should never be used as a heater.
TOXIC fumes can accumulate and cause asphyxiation.
WThis is NOT a tabletop griddle. Therefore, do NOT operate this griddle on
any type of tabletop surface.
WThis griddle is safety certified for use in the United States and/or
Canada only. Do NOT modify for use in any other location. Modification
will result in a safety hazard and will void your warranty.
WThis griddle is for use with liquid propane (LP) gas only. The conversion
to or attempted use of natural gas in this LP gas griddle is dangerous,
may cause bodily harm and will void your warranty.
WDo NOT over heat this griddle as this will damage the griddle and could
cause a fire or an explosion which can cause death, serious bodily
injury or damage to property.
WLP gas characteristics:
a. LP gas is flammable and hazardous if handled improperly. Become
aware of the characteristics before using any LP gas product.
b. LP gas is explosive under pressure, heavier than air, and settles and
pools in low areas.
c. LP gas in its natural state has no odor. For your safety, an odorant is
added that smells like rotten cabbage.
d. Contact with LP gas can cause freeze burns to skin.
WApartment dwellers: Check with management to learn the requirements
and fire codes for using a LP gas griddle in your apartment complex.
If allowed, use outside on the ground floor with a ten foot (3.05 m)
clearance from any structure. Do NOT use on or under balconies.
WLP gas cylinder needed to operate. Only cylinders marked “propane”
may be used.
WThe LP gas cylinder must be constructed and marked in accordance
with the Specifications for LP-gas Cylinders of the U.S. Department
of Transportation (D.O.T.), Cylinders, Spheres and Tubes for the
Transportation of Dangerous Goods; or the National Standard of Canada,
CAN/CSA-B339.
WLP gas cylinder must be arranged for vapor withdrawal.
WDented or rusted LP gas cylinders may be hazardous and should be
checked by your LP gas supplier prior to use.
WThe LP gas cylinder should not be dropped or handled roughly.
WLP gas cylinders must be stored outdoors out of the reach of children
and must not be stored in a building, garage or any other enclosed area.
Your cylinder must never be stored where temperatures can reach over
125°F.
WDo NOT insert any tool or foreign object into the valve outlet or safety
relief valve. You may damage the valve and cause a leak. Leaking
propane may result in an explosion, fire, severe personal injury or death.
WDo NOT block holes in sides, bottom or back of griddle.
WNever keep an LP gas cylinder in a hot car or trunk. Heat will cause the
gas pressure to increase, which may open the relief valve and allow gas
to escape.
WDo NOT store a spare LP gas tank under or within 25 feet (7.62 m) of this
appliance.
WNever attempt to attach this griddle to the self-contained LP gas system
of a camper trailer, motor home or house.
WThe use of alcohol, prescription or non-prescription drugs may impair
the consumer’s ability to properly assemble or safely operate the
appliance.
WStrong odors, colds, sinus congestion, etc. may prevent the detection of
propane. Use caution and common sense when testing for leaks.
WNEVER use lighter fluid, lava rocks, gasoline, kerosene or alcohol with
this product.
WYour griddle has been checked at all factory connections for leaks.
Recheck all connections as described in the “Operating Instructions”
section of the manual, as shipping can loosen connections.
WCheck for leaks even if your unit was assembled for you by someone
else.
WDo NOT operate if a gas leak is present. Gas leaks may cause a fire or
explosion.
WYou must follow all instructions in the “Checking for Leaks” section
before operating. To prevent a fire or explosion hazard when testing for
a leak:
a. Always perform a leak test before lighting the griddle and each time
the cylinder is connected for use.
b. No smoking. Do NOT use or permit sources of ignition in the area
while conducting a leak test.
c. Conduct the leak test outdoors in a well-ventilated area.
d. Do NOT use matches, lighters, or a flame to check for leaks.
e. The use of alcohol, prescription or non-prescription drugs may
impair the consumer’s ability to properly assemble or safely operate
the appliance.
f. Strong odors, colds, sinus congestion, etc. may prevent the
detection of propane. Use caution and common sense when testing
for leaks.
g. Do NOT use griddle until any and all leaks are corrected. If you are
unable to stop a leak, disconnect the LP gas supply. Call a gas
appliance serviceman or your local LP gas supplier.
WDo NOT store or use gasoline or other flammable liquids or vapors
within 25 feet (7.62 m) of this appliance.
WDo NOT use in an explosive atmosphere. Keep griddle area clear and
free from combustible materials, gasoline and other flammable vapors
and liquids.
WMinimum clearance from sides and back of unit to combustible
construction is 21 inches (53 cm). Do NOT use this appliance under any
type of overhang or roof.
WIt is essential to keep the griddle’s regulator and valve assembly,
burners and circulating air passages clean.
WInspect griddle before each use.
WDo NOT alter griddle in any manner. Any alteration will void your
warranty.
WDo NOT use the griddle unless it is COMPLETELY assembled and all parts
are securely fastened and tightened.
WThis griddle should be thoroughly cleaned and inspected on a regular
basis.
WClean and inspect the hose before each use of the appliance. If there
is evidence of abrasion, wear, cuts or leaks, the hose must be replaced
prior to operation.
WUse only the pressure regulator provided. Use only the replacement
pressure regulator specified by RevoAce Inc. Limited
WDo NOT attempt to repair or alter the pressure regulator for any
assumed defect. Any modification to this assembly will void your
warranty and create the risk of a gas leak and fire. Use only authorized
replacement parts supplied by manufacturer.
WUse only RevoAce Inc. Limited factory-authorized parts. The use of any
part that is not factory-authorized can be dangerous and will void your
warranty.
WDo NOT operate this appliance without reading “Operating Instructions”
in this manual.
WDo NOT touch metal parts of griddle until they have completely cooled
to avoid burns, unless you are wearing protective gear (pot holders,
gloves, BBQ mitts, etc.).
WDo NOT install or use in or on boats or recreational vehicles (RV).
WDo NOT use griddle in a vehicle trunk, station wagon, mini-van or sport
utility vehicle (SUV).
WDANGER: Failure to follow the dangers, warnings and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion
causing damage to property.
WWARNINGS:
Important Safeguards - LP Gas

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 3
Important Safeguards - LP Gas
WWhen cooking, fire extinguishing materials should be readily accessible.
In the event of an oil/grease fire, do NOT attempt to extinguish with
water. Use type BC or ABC dry chemical fire extinguisher or smother
with dirt, sand or baking soda.
WMove gas hoses as far away as possible from hot surfaces and dripping
hot grease.
WDo NOT use griddle in high winds.
WNever lean over the griddle when lighting.
WDo NOT leave a lit griddle unattended. Keep children and pets away from
griddle at all times.
WDo NOT leave griddle unattended while preheating or burning off food
residue on high. If griddle has not been cleaned, a grease fire can occur
that may damage the product.
WDo NOT place empty cooking vessels on the appliance while in
operation.
WUse caution when placing anything on the griddle while the appliance is
in operation.
WDo NOT attempt to move griddle when in use. Allow the griddle to cool
before moving or storing.
WLP gas cylinder must be properly disconnected and removed prior to
moving this griddle.
WStorage of griddle indoors is permissible only if the cylinder is
disconnected, removed from the griddle and properly stored outdoors.
WDo NOT attempt to disconnect the gas regulator from the cylinder or any
gas fitting while the griddle is in use.
WDisconnect LP gas tank when not in use.
WAlways place your griddle on a hard, non-combustible, level surface. An
asphalt or blacktop surface may not be acceptable for this purpose.
WDo NOT use directly on wooden decks.
WKeep all electrical cords away from a hot griddle.
WAfter a period of storage and/or non-use, check for leaks, burner
obstructions and inspect for any abrasion, wear or cuts to the hose.
WFailure to not wait five minutes to allow the gas to clear if the griddle
does not light, may result in an explosive flame-up.
WNever operate griddle without griddle surface installed.
WAlways use a meat thermometer to ensure food is cooked to a safe
temperature.
WUse protective gloves when assembling this product.
WDo NOT force parts together as this can result in personal injury or
damage to the product.
WNever cover entire cooking area with aluminum foil. Laying the foilon
the grates can restrict the intended air flow inside the grill, create
barriers to the proper flow of grease to the catch pan, which sets the
stage for lots of it to build up on the bottom tray, which in turn, builds
the potential for grease fires and flare ups.
WDeaths, serious injury or damage to property may occur if the above is
not followed exactly.
WPlace dust cap on cylinder valve outlet whenever the cylinder is not in
use. Only install the type of dust cap on the cylinder valve outlet that is
provided with the cylinder valve. Other types of caps or plugs may result
in leakage of propane.
WDo NOT store a spare LP gas cylinder under or near this appliance.
WNever fill the cylinder beyond 80 percent full.
WIf the above is not followed exactly, a fire causing death or serious
injury may occur.

Outdoor Portable LP Gas Griddle
Model No. GGC2030M
4
Parts List
1Lid* G2030-010
2Lid Handle* G2030-020
3Logo* B0109-BRA
4Griddle Surface* G2030-030
5Griddle Body Assembly* G2030-040
6Left Burner Assembly* G2030-050
7Right Burner Assembly* G2030-060
8Control Knob Bezel (2)* G1143-090
9Control Knob (2) G0850-G23
10 Grease Cup G1860-060
11 LP Gas Tank Support* G2030-070
12 Side Shelf* G2030-080
13 Regulator G2030-090
14 Slide* G2030-100
15 Left Leg Assembly* G2030-110
16 Right Leg Assembly* G2030-120
17 Foot A (2)* B003-05D
18 Wheel Axle (2) G2030-130
19 Wheel (2) B003-02E
20 Foot B (2)* B003-05B
21 Safety Latch*
22 Lock A( 2)* B0107-E05
23 Lock B (2)* B0107-I09
* Pre-assembled
Expanded View
3
1
2
4
12
67
8
9
11
13
14
15
16
17
18
19
19
20
18
10
5
21
23
22
22
23

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 5
1
DO NOT RETURN TO PLACE OF PURCHASE.
For assistance, call 1.800.694.0013 toll-free. Please have
your owner’s manual and model number available for
reference.
Note: The model number can be found on the back of the griddle.
Assembly Tips:
1. Select an area where you will assemble this product. To
protect components, choose a smooth surface that’s free of
cracks or openings.
2. Spread out all parts.
3. Tighten all hardware connections by hand first. Then, before
completing each step, go back and fully tighten all hardware.
Be careful not to over-tighten. That could damage surfaces or
strip threads.
4. For best results, complete each step in the order presented.
After assembly you will need:
• (1) Leak Detection Solution (instructions on how to make
solution are included in “Operating Instructions” section).
• (1) 14.1 oz or (1) 16.4 oz LP gas tank (not included).
Typical assembly is approximately 10 minutes.
3
Unlock Safety Latch
2
Attach Wheels
4
Unfold Legs
Assembly Instructions
12
Note: The wrench is required (included).

Outdoor Portable LP Gas Griddle
Model No. GGC2030M
6
5
Lock Right Leg
7
Attach Regulator (1lb LP tank is not included)
6
Attach Control Knobs and Grease Cup
8
Secure LP Gas Tank
Assembly Instructions (continued)
1
2
3
1
2
3

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 7
4
Fold Griddle
Griddle Storage & Transporting
1
Remove Regulator
2
Remove LP Gas Tank and Attach Regulator
3
Fold Upper LP Gas Tank Support
1
2
3
Note: The safety latch must be unlock before folding the griddle.
Note: Make sure the grease cup is empty before folding the griddle.
1
2
3
3
12

Outdoor Portable LP Gas Griddle
Model No. GGC2030M
8
4
Fold Griddle
Griddle Storage & Transporting (Continued)
5
Lock Safety Latch
6
Lock Lid and Unlock Lid
Note: The safety latch must be locked after folding the griddle.
Note: Lid must be locked before transporting grill.
Note: The cart can’t be removed from the griddle.
Note: Make sure the grease cup is empty before folding the griddle.
Note: Always unlock and open lid before lighting grill.
Unlocking Lid
Locking Lid
1
1
1
2
2
2
3
3

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 9
Installing 20lb LP Gas Tank
1
Attach Regulator
2
Attach Adapter Hose for 20 lb Tank (Not included).
3
Secure LP Gas Tank (Not included)
4
Connect and Disconnecting LP Gas Tank
1 2 3
4
5

Outdoor Portable LP Gas Griddle
Model No. GGC2030M
10
This griddle is designed to operate with a 1 lb. 7.75
in. or 10.6 in. high disposable / 16.4 oz. or 14.1 oz.
propane gas tank (DOT 39 Cylinder) (Figure 1).
DO NOT ATTEMPT TO REFILL ANY 1 lb. (16.4 oz. or
14.1 oz.) PROPANE GAS TANKS!
Connecting LP Gas Tank
Only cylinders marked “propane” may be used.
Note: 1 lb cylinders may form frost when near empty.
1. Make sure the control knob is in the
“•OFF” position (Figure 3).
2. Lubricate the threads of the regulator with
petroleum jelly. Line up threads on LP gas tank
with regulator.
3. Insert and rotate LP gas tank clockwise until
they fit snugly together. HAND TIGHTEN ONLY. Be
careful not to crossthread when screwing in tank
(Figure 4).
4. Perform leak test per “Checking for Leaks”
section.
Disconnecting LP Gas Tank
WCAUTION: The LP gas tank must be
removed when this appliance is not in
use.
1. Turn the control knob to the “•OFF” position
(Figure 3).
2. Rotate LP gas tank counterclockwise until it is
detached (Figure 5).
3. Store the LP gas tank in a proper location, per
instructions on the LP gas tank.
Operating Instructions
Checking for Leaks
Burner Connections
1. Make sure the regulator is securely fastened.
Note: The brass nut should be ¼ to ½ turn past
tight. The regulator will rotate 360º even when the
brass nut is tightened.
2. Visually check the connection between the burner
and regulator (Figure 6).
3. Make sure the burner/venturi tube fits over the
orifice (Figure 2).
WWARNING: Failure to inspect this
connection or follow these instructions
could cause a fire or an explosion
which can cause death, serious bodily
injury or damage to property.
4. Please refer to diagram for proper installation
(Figures 2 and 6)
5. If the burner/venturi tube does not rest flush
to the orifice, as shown, please contact
1.800.694.0013 for assistance
6. If the burner and regulator do not fit properly
or if you have any questions, please contact
1.800.694.0013 for assistance.
Tank/Gas Line Connection
1. Make 2-3 oz. of leak detection solution by mixing
one part liquid dishwashing soap with three parts
water.
2. Make sure control knob is in the “•OFF” position
(Figure 3).
3. Apply the leak detection check solution on all “X”
locations (Figure 6).
Installing LP Gas Tank
a. If any bubbles appear, remove the LP gas tank and reconnect, making sure the
connection is secure.
b. If you continue to see bubbles after several attempts, remove the LP gas tank per
“Disconnecting LP Gas Tank” section, and contact 1.800.694.0013 for assistance.
c. If no bubbles appear after one minute, turn control knob to the “•OFF” position,
wipe away solution and proceed.
First Use
1. Make sure all labels, packaging and protective films have been removed from the griddle.
2. Light griddle per “Lighting” section.
3. Remove manufacturing oils before cooking on this grill for the first time by operating
the grill for at least 15 minutes on (HIGH). This will “heat clean” the internal parts and
dissipate odors.
4. Season your griddle per “Seasoning Griddle” section.
Operating the LP Gas Griddle
Lighting
WCAUTION: Keep outdoor gas cooking appliance area clear and free
from combustible materials, gasoline and other flammable vapors and
liquids.
WCAUTION: Do NOT obstruct the flow of combustion and ventilation air.
WCAUTION: Check and clean burner/venturi tubes for insects and insect
nests. A clogged tube can lead to a fire.
WCAUTION: Do NOT use non-stick cooking sprays because they contain
a lot of water and can burn onto the griddle, damaging the surface.
WCAUTION: Do NOT use corn oil as it contains a high level of sugar,
which can carmelize and burn onto the surface.
1. Check for obstructions of airflow to the
burners. Spiders, insects and webs can clog
the burner/venturi tube. A clogged burner/
venturi tube can lead to a fire.
2. Control knob must be in the “•OFF”
position (Figure 3).
3. Connect LP gas tank per “Connecting LP
Gas Tank” section.
4. Push and turn any control knob to (HIGH).
The burner should light. If it does not, repeat
up to three times.
5. If ignition does not occur in 5 seconds,
turn burner control knob “•OFF,” wait 5
minutes, and repeat lighting procedure.
6. If igniter does not light burner, use a lit
match to light burner manually.
a. Access the burner through the hole
in bottom bowl or side as indicated
(Figure 7).
b. Turn the control knob to (LOW) and
position the lit match near side of the
burner.
7. After lighting, observe the burner flame.
Make sure all burner ports are lit and flame
height matches illustration (Figure 8).
WCAUTION: If burner flame goes out
during operation, immediately turn the control knob “•OFF” and let
the gas clear for 5 minutes before re-lighting.
Turning Off
WCAUTION: The LP gas tank must be removed when this appliance is
not in use.
1. Turn control knob to the “•OFF” position (Figure 3).
Note: A “poof” sound is normal as the last of the LP gas is burned.
2. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
3. Season your griddle per “Seasoning Griddle” section.
Cooking
WCAUTION: Do NOT leave griddle unattended while preheating or
burning off food residue on (HIGH). If griddle has not been cleaned, a
grease fire can occur.
1. Light griddle per “Lighting” section.
2. Preheat griddle on (HIGH).
3. Adjust control knob to desired flame height.
4. Wear protective gloves and use long handle tongs to place food onto griddle surface.
5. Cook until desired internal food temperatures are achieved.
6. Turn griddle off per “Turning Off” section.
Controlling Flare-ups
Operating Instructions (continued)
Figure 1
1 lb
453 g
7.75 in. / 19,7 cm
3.875 in. / 9,8 cm
2.9 in. / 7,4 cm
1 lb
465 g
10.6 in. / 27 cm
Figure 2
Burner/
Venturi Tube
LP Gas
Valve with
Orifice
LP Gas
Connection
Figure 3
OFF
HIGH
LOW
Figure 4
Figure 5
Figure 6
Figure 7
Match
Figure 8
Burner
Flame Slight
Yellow
Slight
Blue
Dark
Blue
IMPORTANT
Before first use and after each use, always
season your griddle per “Seasoning Griddle”
section.

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 11
WCAUTION: Putting out grease fires by only closing the lid is not
possible.
1. If a grease fire develops, turn control knob to the “•OFF”
position. Do NOT use water on a grease fire. This can cause the
grease to splatter and could result in serious burns, bodily harm or
other damage.
2. Do NOT leave griddle unattended while preheating or burning off
food residue on (HIGH). If griddle has not been cleaned, a grease
fire can occur.
WWARNING: When cooking, fire extinguishing materials should be
readily accessible. In the event of an oil/grease fire, use type BC dry
chemical fire extinguisher or smother with dirt, sand or baking soda.
Do NOT attempt to extinguish with water.
Flare-ups are a part of cooking meats on a griddle and add to the unique flavor of grilling.
Excessive flare-ups can over-cook your food and be dangerous.
Important: Excessive flare-ups result from the build-up of grease in the grease cup.
If a grease fire occurs, turn the control knob to “• OFF” until the grease burns out.
If excessive flare-ups occur, do NOT pour water onto the flames.
Minimize Flare-ups:
1. Trim excess fat from meats prior to cooking.
2. Cook high fat content meats on (LOW) setting or indirectly.
3. Ensure that your griddle is on a hard, level, non-combustible surface and the grease is
allowed to drain into grease receptacle.
Cleaning and Care
WCAUTION:
1. All cleaning and maintenance should be done when griddle is cool
and with the fuel supply disconnected.
2. Do NOT clean any griddle part in
a self-cleaning oven. The extreme
heat will damage the finish.
3. Do NOT enlarge valve orifices or
burner ports when cleaning the
valves or burners.
Notices
1. This griddle should be thoroughly cleaned and
inspected on a regular basis.
2. Abrasive cleaners will damage this product.
3. Never use oven cleaner to clean any part of
griddle.
Before Each Use
1. Keep the griddle area clean and free from any
combustible materials, gasoline, and other
flammable vapors and liquids.
2. Do NOT obstruct the flow of the combustion of LP
gas and the ventilation of air.
3. Keep the ventilation opening(s) of the LP gas tank
area free and clear from debris.
4. Visually check the burner flames to make sure
your griddle is working properly (Figure 9).
5. See below for proper cleaning instructions.
6. Check for obstructions of airflow to the burners.
Spiders, insects and webs can clog the burner/
venturi tube. A clogged burner/venturi tube can
lead to a fire.
Cleaning Surfaces
1. Wipe surfaces clean with mild dishwashing detergent or baking soda mixed with water.
2. For stubborn surfaces, use a citrus-based degreaser and a nylon scrubbing brush.
3. Rinse clean with water.
4. Allow to air dry.
Cleaning Main Burner
1. Turn off per “Turning Off” section.
2. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
3. Remove control knob.
4. Remove griddle by lifting it off the cart.
5. Remove burner by removing the fasteners, which secure the burners to the frame bottom.
6. Lift burner up and away from gas valve orifice.
Operating Instructions (continued)
Figure 9
Burner Flame Conditions
Use this chart to see if your burners
need to be cleaned.
1-2 in. /
25.4 - 50.8 mm
Normal: Soft blue flames with yellow
tips between 1 in. - 2 in. height.
Needs cleaning: Noisy with hard
blue flames.
Has to be replaced: Wavy with
yellow flames.
7. Remove all food residue and dirt from burner surface.
8. Disconnect wire from spark electrode.
9. Clean inlet of burner with small bottle brush or compressed air.
10. Clean any clogged ports with a stiff wire (such as an opened paper clip).
11. Inspect burner for any damage (cracks or holes). If damage is found, replace with a new
burner from manufacturer.
12. Re-install burner. Checking to insure that gas valve orifice is correctly positioned inside
the burner/venturi tube. Also, check position of spark electrode.
13. Connect wire to spark electrode.
14. Replace griddle.
15. Connect LP gas tank per “Installing LP Gas Tank” section.
16. Perform leak test per “Checking for Leaks” section.
Before Storing
1. Turn off per “Turning Off” section.
2. Turn all control knobs clockwise to the “•OFF” position.
Note: A “poof” sound is normal as the last of the gas is burned.
3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
4. Clean all surfaces.
5. Lightly coat the burner and cooking grid with cooking oil to prevent excess rusting.
6. Season your griddle per “Seasoning Griddle” section.
7. If storing the griddle indoors, disconnect the LP tank per “Disconnecting LP Gas Tank”
section.
8. Place the protective cap cover on the LP tank and store the tank outdoors in a well-
ventilated area out of direct sunlight.
9. If storing the griddle indoors, cover the griddle and store in a cool dry place.
10. If storing the griddle outdoors, cover the griddle with a griddle cover for protection from
the weather.
Seasoning Griddle
Important: season your griddle every time you use it.
Griddle chefs at Japanese steakhouses and short-order restaurants season their griddles all
the time, and it is critical for you to do it too. Seasoning helps prolong the life of your griddle,
makes the cooking surface non-stick and helps prevent rust.
For more information, please visit BlueRhino.com/RazorFAQ.
Tools needed for seasoning:
• Metal scraper or metal spatula
• Cooking oil, such as vegetable oil or extra virgin olive oil
• Paper towels
• BBQ stone or steel wool
WCAUTION: Do NOT use corn oil as it contains a high level of sugar,
which can carmelize and burn onto the griddle surface.
First Use
1. Light griddle per “Lighting” section.
2. Keep burners on (HIGH) for 15 minutes.
3. Turn griddle off per “Turning Off” section.
4. Allow griddle to cool, but still be slightly warm.
5. Wipe off griddle surface, inner and outer walls with paper towels until clean.
Note: While drying you may notice the towel may have some discoloration. This is
normal.
6. Apply cooking oil onto griddle surface, inner and outer walls and evenly coat with rolled
up paper towels.
7. Repeat this process at least twice.
After Each Use
1. Turn griddle off per “Turning Off” section.
2. While the griddle is still warm, gently scrape off all food residue with a scraper.
3. Wipe down griddle surface, inner and outer walls with a towel or paper towels.
4. For stubborn food residue:
a. Light griddle per “Lighting” section.
b. Apply cooking oil onto griddle surface.
c. Allow oil to “boil” food residue off.
d. Repeat steps 1 through 3.
e. If necessary, use a BBQ stone and scrub the food residue off.
f. Continue with “Seasoning Griddle” instructions.
5. Wipe off griddle surface, inner and outer walls with paper towels until clean.
Note: While drying you may notice the towel has some discoloration. This is normal.
6. Apply finishing oil onto griddle surface, inner and outer walls and evenly coat with rolled
up paper towels.
7. Light griddle per “Lighting” section.
8. Keep burners on (HIGH) for 15 minutes or until cooking oil starts to smoke.
9. Turn griddle off per “Turning Off” section.
10. Repeat steps 6-9 a minumum of 2 additional times.
11. Following “Before Storing” section.
Cleaning and Care (continued)

Outdoor Portable LP Gas Griddle
Model No. GGC2030M
12
Cleaning and Care (continued) and to no other person, that if this product is assembled, maintained, and operated in
accordance with the printed instructions accompanying it, then for a period of one (1) year
from the date of purchase, all parts in such product shall be free from defects in material and
workmanship. Manufacturer may require reasonable proof of your date of purchase. Therefore,
you should retain your sales slip or invoice. This Limited Warranty shall be limited to the repair
or replacement of parts, which prove defective under normal use and service and which
manufacturer shall determine in its reasonable discretion upon examination to be defective.
Before returning any parts, you should contact manufacturer’s Customer Service Department
using the contact information listed below. If manufacturer confirms, after examination, a
defect covered by this Limited Warranty in any returned part, and if manufacturer approves
the claim, manufacturer will replace such defective part without charge. If you return defective
parts, transportation charges must be prepaid by you. manufacturer will return replacement
parts to the original retail purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident,
abuse, misuse, alteration, misapplication, improper installation or improper maintenance or
service by you or any third party, or failure to perform normal and routine maintenance on the
product as set out in this owner’s manual. In addition, the Limited Warranty does not cover
damage to the finish, such as scratches, dents, discoloration, rust or other weather damage,
after purchase.
This Limited Warranty is in lieu of all other express warranties. manufacturer disclaims all
warranties for products that are purchased from sellers other than authorized retailers or
distributors, including the warranty of merchantability or the warranty of fitness for a particular
purpose. MANUFACTURER ALSO DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. MANUFACTURER SHALL HAVE NO LIABILITY TO PURCHASER OR
ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES. manufacturer further disclaims any implied or express warranty of, and assumes
no responsibility for, defects in workmanship caused by third parties.
This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other
rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion
or limitation of special, incidental or consequential damages, or limitations on how long a
warranty lasts, so the above exclusion and limitations may not apply to everyone. manufacturer
does not authorize any person or company to assume for it any other obligation or liability in
connection with the sale, installation, use, removal, return, or replacement of its equipment,
and no such representations are binding on manufacturer.
RevoAce Inc. Limited
Hong Kong, China
[email protected]
1.800.694.0013
8:00 am to 4:00 pm central time, Monday to Friday.
Refurbish the Griddle Surface
1. If griddle is off, light per “Lighting” section for 10 minutes. Then turn griddle off per
“Turning Off” section.
2. If griddle is on, turn griddle off per “Turning Off” section.
3. While the griddle is still warm, use a scraper or metal spatula to remove as much rust and
food residue as you can from the griddle surface, inner and outer walls.
4. Apply a liberal amount of cooking oil onto the griddle surface.
5. Using a BBQ stone, scrub the griddle surface. Apply additional cooking oil as need.
6. Wipe off griddle surface, inner and outer walls with paper towels.
7. Repeat steps 3-5 until paper towels no longer show any rust.
8. Apply cooking oil onto griddle surface, inner and outer walls and evenly coat with rolled up
paper towels.
9. Light griddle per “Lighting” section.
10. Keep burners on (HIGH) for 15 minutes or until cooking oil starts to smoke.
11. Turn griddle off per “Turning Off” section.
12. Repeat steps 7-10 until the surface has a nice dark color.
13. Follow “Before Storing” section.
Product Registration
For faster warranty service, please register your product immediately. To register, call
1.800.694.0013.
Replacement Parts
For replacement parts, call 1.800.694.0013.
Limited Warranty
RevoAce Inc. Limited (“manufacturer”) warrants to the original retail purchaser of this product,

Need help? Call 1.800.694.0013
Do not return to place of purchase.
Replacement Parts
1.800.694.0013 13
Troubleshooting
Problem Possible Cause Prevention/Cure
Burner will not light using igniter
LP gas tank is low or empty Replace LP gas tank
LP gas leak
1. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
2. Wait 5 minutes for gas to clear
3. Connect LP gas tank per “Connecting LP Gas Tank” section.
4. Follow “Checking for Leaks” section
Bottom bowl and ash pan are covered with ashes Clear bottom bowl and ash pan of ashes
Wires or electrode covered with cooking residue Clean wire and/or electrode with rubbing alcohol
Electrode and burners are wet Wipe dry with cloth
Electrode cracked or broken - sparks at crack Replacement part(s) may be needed - contact Customer Care at 1.800.694.0013
Wire loose or disconnected Reconnect wire or replacement part(s) may be needed - contact Customer Care
at 1.800.694.0013
Wire is shorting (sparking) between igniter and electrode Replacement part(s) may be needed - contact Customer Care at 1.800.694.0013
Bad igniter Replacement part(s) may be needed - contact Customer Care at 1.800.694.0013
Burner will not light with match
No gas flow
Check if LP gas tank is empty
A. If empty, replace
B. If LP gas tank is not empty, refer to “Sudden drop in gas flow or reduced
flame height” below
LP gas tank is low or empty Replace LP gas tank
LP gas leak
1. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
2. Wait 5 minutes for gas to clear
3. Connect LP gas tank per “Connecting LP Gas Tank” section.
4. Follow “Checking for Leaks” section
Coupling nut and regulator not fully connected Turning the coupling nut about one-half to three-quarters additional turn until
solid stop. Tighten by hand only – do NOT use tools.
Obstruction of gas flow Clear burner/venturi tube
Spider webs or insect nest in venturi Clean burner/venturi tube
Burner port is clogged or blocked Clean burner port
Sudden drop in gas flow or reduced flame height Out of gas Replace LP gas tank
Irregular flame pattern – flame does not run the
full length of burner Burner port is clogged or blocked Clean burner port
Flame is yellow or orange
New burner may have residual manufacturing oils Operate griddle for 15 minutes on (HIGH)
Spider webs or insect nest in burner/venturi tube Clean burner/venturi tube
Food residue, grease, etc. on burner Clean burner
Poor alignment of valve to burner/venturi tube Ensure burner/venturi tube is properly engaged with valve
Flame goes out
High or gusting winds DO NOT use griddle in high winds
Low on LP gas Replace LP gas tank
Overflow valve tripped Refer to “Sudden drop in gas flow or reduced flame height,” above
Flare-up
Grease buildup Remove and clean all griddle parts per “Cleaning and Care” section
Excess fat in meat Trim fat from meat before cooking
Excessive cooking temperature Adjust (lower) cooking temperature
Persistent grease fire Grease trapped by food buildup around burner system
1. Turn control knob to “•OFF”
2. Let fire burn out
3. After griddle cools, remove and clean all griddle parts per “Cleaning and Care”
section
Flashback (fire in burner tube(s)) Burner and/or burner tubes are blocked Clean burner and/or burner/venturi tube
For more assistance, please call 1.800.694.0013.

Outdoor Portable LP Gas Griddle
Model No. GGC2030M
14