RC4 LumenDim6 User manual

RC4
Wireless
Wireless Dimming | Wireless DMX | Wireless Motion
Since 1991
LumenDim6
Quick Start Guide
Rev. 1.0

2 32 3
RC4 LumenDim6
1. DMX Data Indicator
2. Function and COP* Indicator
3. Function Button
4. Set ABC and Set DEF Buttons
5. DimA - DimF Dimmer Indicators
6. RF Connect Indicator for Transmitter Linking
7. RF Connect (Link) Button
8. Anderson PowerPole Connections for Power and Outputs
9. DMX In/Out Data Port
10. Power Input Connections (45A PowerPole)
11. Load Connections (2 x Common +, DimA- through DimF -)
* COP means “Computer Operating Properly.” This indicator always shows a blink pattern,
proving that internal rmware is running. Dierent patterns indicate various modes and advanced
settings.
9
8
5
4
8
10
11
10
1 2 3 76

4 5
LumenDim6 Quick Start Guide
This guide will get you started using your RC4 LumenDim6. Most LumenDim6
users will nd all the information they need right here.
Your LumenDim6 also has a wide variety of expanded features for advanced
users. You can nd out more about all of them in the RC4 Knowledge Base at
http://rc4.info.
Registering Your Product
Registering your LumenDim6 is quick and easy. After registration, you’ll be
notied of new rmware updates, and warranty claims can be resolved more
quickly.
Please complete your registration at:
www.rc4wireless.com/support/register/
4 5
LumenDim6 System Components
To use your LumenDim6 wireless dimmer you will need:
• A DMX lighting console.
• A LumenRadio CRMX-compatible wireless transmitter like the
RC4 LumenDimIO or the LumenRadio TX1.
• A battery or DC power supply for the dimmer and loads you will be
operating with it.
• Anderson PowerPole shells and pins (one set has been provided with your
LumenDim6), and a crimping tool for those pins.
Anderson PowerPole Connectors
PowerPole shells are available in a range of colors. Pins are available with
15A, 30A, and 45A ratings. If you are running your LumenDim6 at close to the
maximum rated power handling, you MUST use 45A pins at the power input.
Do not exceed 45A in total for the 6 combined dimmer loads.
Each dimmer output can deliver up to 10A of dimming power, but you cannot
run all 6 channels at 10A because this exceeds the input power limit. If all
channels are loaded equally, the maximum load per channel is 7.5A.
The legend on the back of your LumenDim6 provides part numbers of
commonly used shells and pins. A complete set of shells and pins is also
available directly from RC4 Wireless.

6 76 7
Unlink the LumenDim6
If the blue RF Connect LED on the LumenDim6 blinks continuously, it is looking
for a transmitter that it was previously linked with.
To unlink it, press and hold RF Connect for several seconds until the blue LED
goes o and stays o.
If the RF Connect LED remains on, or is blinking, repeat the process until it
stays o.
When the RF Connect LED is o, the LumenDim6 is ready to be linked to your
transmitter.
NOTE: Link status is not aected by performing a Factory Reset.
Performing a Factory Reset
If someone else has used your LumenDim6, or you just
want to get back to a known conguration, performing
a factory reset is easy:
Power on the device. The green COP indicator will be
blinking.
Press and hold Func, briey tap (press and release) the
SetABC button, then release Func. Four indicators will
blink to conrm that factory settings are restored.
NOTE: This does NOT aect transmitter linking.
PRO TIPS:
Bending a single paper clip into a U shape will enable
you to easily reach and press both buttons together.
If you are not sure what mode or setting you may have
selected, you can always get back to a known starting
point by returning to factory defaults.

Title
Text
8 9
Linking Transmitter and Receiver
In this example, we’re using an RC4 LumenDimIO transmitter. Have both
devices powered on. Put the LumenDimIO Mode switch in the transmit
position, then tap the Link button. The Link button is recessed under the small
slot to the right of the blue RF Connect LED. Tap it with a small screwdriver or
the end of a bent paperclip.
The blue RF Connect LEDs on both the LumenDimIO and the LumenDim6 will
ash for several seconds and then remain steady, indicating that they are
linked.
8 9
MODE
PUSH
Link Button
Test the Wireless Link with Default Address Settings
When you receive your new LumenDim6, or after restoring default settings, it
will be set to DMX address 1 for dimmer A, address 2 for dimmer B, etc.
Before changing any dimmer settings, play with the DMX levels for these
addresses and see your wireless dimmer outputs work.
The DimA, B, C, D, E, and F indicators on the side of the LumenDim6, below
the grey negative terminals for each, are directly connected to the dimmer
outputs: they show you exactly what the dimmers are doing.
Setting the DMX Address
Assigning DMX channels and dimmer curves is easy using RC4 OneTouch™:
On your DMX lighting console, bring up one dimmer (DMX output channel)
that will be your LumenDim6 starting address. For example, if you want your
rst LumenDim6 dimmer on DMX channel 60 with a curve that is optimized
for LEDs, bring up 60 @ 30% at the console. Tap SetABC and the DimA
indicator will come on @ 30%.
The channel level of 30% selects one of several dierent curves. This one is
optimized for LEDs. Other curves are explained on Page 13.

10 11
Subsequent Channel Assignment
When you set DimABC, all 6 dimmers are automatically
set sequentially. For example, if you have set DMX
channel 60 for DimA, DimB is now assigned to channel
61, DimC is on 62, and so on, all the way up to DimF
being set on channel 65.
Non-Sequential Channel Assignment
Each set of 3 dimmers, ABC and DEF, are always
sequential, but the two sets do not have to be.
You can use RC4 OneTouch™ with the Set buttons for
each individual group. For example, if you want DimDEF
to be set to DMX address 11, bring up 11 @ 30%
(for the LED curve) at the board and press the SetDEF
button.
Remember: SetABC assigns all 6 dimmers sequentially.
The SetDEF button work individually to set only the
last 3 dimmers. Always use SetABC rst, then set DEF
dierently if you need to.
10 11
Connecting Your Lamps, LEDs, Motors and More*
To really use your LumenDim6, you must connect a lamp, LED, motor, or other
load to each dimmer. When you’re connecting anything to your LumenDim6, be
sure that the LumenDim6 is powered down. Connect everything rst, then turn
on power.
The red output connections are positive (+), the grey connections are negative (-).
Dimming occurs on the negative side. The positive connections are all
connected together inside the LumenDim6.
* DimC , D, E, and F on the LumenDim6 can control a variety of devices including solenoids, relays, servo
motors, and much more. DimA and B are intended for LED dimming only.
Power Input: 6 - 35VDC
Do not exceed voltage
rating for connected loads. Common Positive +

12 13
Dimming and Controlling Multicolor LEDs
The illustration on the previous page shows an RGB color mixing LED device.
There are 4 wires: a black wire for the 12V common positive (+), and three
colored wires, red/green/blue, for the three unique negative leads. The color
of the common positive may vary, it is not always black.
The common positive should be connected to one of the two red output
terminals. All of the (+)terminals are connected together inside the
LumenDim6. The two (+)terminals make it easy to connect two RGB light
sources, each with their own common positive wire.
Dimming happens on the negative (–) connections.
The red wire should be connected to the grey (–) connection for DimA.
The green wire should be connected to the grey (–) terminal for DimB.
The blue wire should be connected to the grey (–) terminal for DimC.
If using an RGBA, RGBW, RGBA, RGBTD (T is tungsten or warm white, D is
daylight or cool white), or other multi-channel xture or LED device, the
additional wires (often amber, yellow, warm white, or cool white) should be
connected to the grey (–) terminals for DimD, E, and F as needed.
If using two RGB xtures or LED devices, connect the rst one to DimA, B, and
C, and connect the second to DimD, E, and F.
12 13
Choosing Other Dimmer Curves or Proles
The LumenDim6 default is the ISL dimmer curve, which is best for LEDs. This is
also the curve that is selected with RC4 OneTouch™ when the DMX level is at
30%.
There are dimmer curves for dierent kinds of lamps, motors, and more.
Detailed information can be found online by searching dimmer curves at
http://rc4.info/.
The most common curves are selected using these DMX channel levels and
RC4 OneTouch™ with the Set buttons as outlined on page 9:
Non-Dim 100% (80% or higher)
Use for relays, solenoids, air valves, etc.
Linear 70% (60 - 79%)
For incandescent, halogen, tungsten lamps.
ISL Fast 50% (40 - 59%)
For LEDs when fast blinks and ashes are required.
RC4 Digital Persistence™ is disabled.
ISL Slow 30% (20 - 39%)
Best for typical LED applications, with RC4 Digital Persistence™.
For super smooth 19-bit dimming. (default setting)

14 15
Advanced Features
The LumenDim6 is a multifaceted device for users of all experience levels. The
features below can be explored further at http://rc4.info/ or by asking us for
help at [email protected]:
• Using a small adaptor cable, the LumenDim6 can be used as a wireless data
receiver to deliver DMX to other devices. It can also be used as a wired
DMX dimmer: the miniplug DMX port becomes an input when the device is
not linked to a transmitter.
• When using the LumenDim6 for cinema (motion picture capture), PWM
frequencies can be adjusted for the smoothest dimming without banding or
other camera artifacts.
• The LumenDim6 has a wide variety of dimmer curves that can ring
telephones and more (using DimC, D, E, and F).
• Using the RC4 Flkr Eects Engine™, you can create many unique eects
including candle icker, analog tv screen noise, welding spark, and much
more.
• An HSL (Hue/Saturation/Level) processor can be enabled, making it easy to
nd a specic color and dim it up and down without color variation.
14 15
Caring for Your LumenDim6
• The LumenDim6 should not be used with AC power or with any voltage
higher than 35VDC. Doing so will severely damage the device and is
extremely dangerous for the operator.
• Do not exceed the maximum total power handling of the LumenDim6,
which is 45A. That is 500W at 12V, 1000W at 24V, shared across the six
dimmer channels.
• Always use a fuse or circuit breaker at the source of power and always use
an appropriate wire size for the fuse rating. For example, if using a 40A
fuse, use wire that can safely carry 40A.
• The LumenDim6 should be kept away from excessive heat, cold, dust and
moisture.
• Do not immerse in water or other uids.
• Dimmers generate heat when operating. Allow space for air to move around
the unit for cooling, especially when using high-current loads.
The LumenDim6 is a high-power, high-current device. Failing to observe
appropriate safety precautions can result in re or other risk. RC4 Wireless
cannot be held responsible or liable in such cases. Operate the LumenDim6
at your own risk.

1616
Get in Touch
1-866-258-4577 Toll Free, North America
1-919-229-9950 North Carolina, USA, Local
[phone] London, UK
1-866-237-6641 Toll Free Fax, North America
Email: [email protected]
Website: www.rc4wireless.com
Knowledge Base: http://rc4.info
We’re here to help you at any time.
James David Smith
President and Chief Product Designer
RC4 Wireless