Real Fyre RR1A User manual

1
INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.
This guide serves as a supplement to any remote information found in the burner, pilot kit, and remote instructions.
Read all instructions completely and carefully prior to product use. Select models shown, design may vary.
IINSTALL BATTERIES
Remote Receiver
Remote Transmitter
• Remove lid.
• Install "12V" battery (included).
• Re-secure lid.
• Remove lid.
• install four "AA"
batteries (included).
• Re-secure lid.
(Remove
lid)
REV 0 - 1411031020 L-A2-390
RR1A / RR2A Remote
Quick Start Guide
II INSTALL WALL MOUNT (IF APPLICABLE)
Receiver
slide
button
Cover plate
Remote
receiver
Plastic switch box
(not included)
WALL
• For wall mounting: refer to the remote
instructions for install details.
• Route the wires to the fireplace and proceed
to the following CONNECT TO VALVE
section.
Important: DO NOT install 120VAC wires to
remote receiver.
Wall Mount

2
REV 0 - 1411031020 L-A2-390
III CONNECT TO VALVE
Select models require installation of remote receiver to burner system.
Connecting to an 01 Valve
Connecting to an 11/12 Valve
Switch Box Assembly
(Burner System)
Remote Receiver
(Remote System)
• Locate two free wires on switch box assembly.
• Connect remote wires.
• Ensure all connections are fully attached.
AB
Remove
connectors
Connect
remote wires
(wires to
burner)
Switch
(Burner System)
Remote Receiver
(Remote System)
(burner
valve)
Two methods exist (depending on model):
Toggle Switch (and select ON/OFF Switches)
• Locate switch pre-installed to burner valve.
• Remove and discard red connectors on switch (A).
• Connect remote wires to now exposed terminals (B).
• Ensure all connections are fully attached.
Important: DO NOT allow terminals to touch.
Valve
• Connect remote wires to exposed terminals
on valve.
• Ensure all connections are fully attached.
OR
Valve
(Burner System)
Remote Receiver
(Remote System)
(burner
valve)
Any ON/OFF or toggle switch (part of burner system) must be in off position when using remote system.
The ON/OFF switch must be in off position when using remote system.
Toggle switch shown
(design and location
may vary)

3
REV 0 - 1411031020 L-A2-390
VOPERATION
Follow operation section found in burner and/or remote instructions.
Note: Any ON/OFF or toggle switch (part of burner system) must be in off position when using remote system.
Note: Be sure receiver and transmitter are within 20' - 25' operating range.
Note: A triple beeping receiver indicates overheating. Turn off burner, allow to completely cool, and properly
relocate receiver (see above section).
VI SYNCING REMOTE SYSTEM
Note: If remote does not function, and batteries with an adequate power
level are installed, follow steps below.
Ensure burner system is off and completely cool.
Slide switch on remote receiver to REMOTE position. Next press LEARN
button and release.A beep will be heard.Then press and hold ON button on
remote transmitter; a series of beeps should be heard. The remote system
is now synced. Light burner to test.
LEARN
REMOTE ONOFF
IV PLACE REMOTE RECEIVER (IF APPLICABLE)
Proper placement is crucial to prevent damage and overheating.
Fireplace
If burner instructions include specific
placement instructions, follow them.
• Unless otherwise stated in burner
instructions, place receiver at front right
of fireplace as far from burner system
as possible.
Important: Place receiver 6" from
burner/flame (minimum).
• Place plastic cover over receiver.
DO NOT cover receiver with lava media or other items.
6" min.
(Burner)
(Firebox)
11 model shown

4
Please use this page to record any information that you may want to have at hand.
NOTES PAGE
REV 0 - 1411031020 L-A2-390