Realinn Rl6100-2d User manual

RL6100-2D

2D Barcode Scanner

User Manual

Service mailbox

ser[email protected]

In order to correctly use the bar code scanner, please read the instruction

carefully and do not arbitrarily scan the settings code otherwise some

settings may not be available.

Please keep this instruction for reference in the future.

If you have any question or concern about the operation of the scanner,

please contact us at Email:

serv[email protected]

Contents

Product Specification

.....................................

Packing List

.....................................

Battery & Charging

....................................

Quick Guide

....................................

FAQs

....................................

Optional Function settings

....................................

1. Pairing Mode Setting

................................................

2. Upload Mode Setting

................................................

3. Scanning Mode Setting

................................................

4. Anti-duplication Setting

................................................

5. Battery Remaining

................................................

6. Aiming & LED Light Setting

................................................

7. Case Sensitivity Setting

................................................

8. Identity Barcode Type

................................................

9. Frequently-used End Character Setting

................................................

10. Beep Setting

................................................

11. Interface Setting

................................................

12. Stand-by Setting

................................................

13.Keyboard Language Setting

................................................

14. Enable / Disable Barcode Type

................................................

15.Insert and Dlelete Character

................................................

ASCII Barcode Table

................................................

Product Specification

Model-Number

RL6100-2D

Connection

433MHz Wireless

Memory

2M = 10000 barcodes

Battery capacity

2200mAh

Voltage

DC 5V

Standby current

18uA-5mA

Charging power

5V-400mA

Printing Contract

>25%

Light source

617nm LED

LED life

12000 hours

Button life

8000,000 times

Sensor

640*480 CMOS

Illumination

6500K LEDs

Indication

Buzzer & LED

Resolution

3 mil

CPU

ARM 32-bit Cortex

Printing Contract

>25%

Decoding speed

500 times/sec

Scanning angle

Angle of rotation360°, inclination± 65°,declination ± 60°

Anti-interference

0-100000Lux Max

Drop test

2.0m

Certificate

CE，FCC，RoHS ，IP54

Applicable 1D barcode

UPC-A，UPC-E，EAN-8，EAN-13，Code 128， Code 39，Code 93，

Code 11，Interleaved 2 of 5，Standard 2 of 5，Industrial 2 of 5,Coda

bar

MSI ，etc.

Applicable 2D barcode

QR Code, Data Matrix，PDF417，Aztec code，Maxicode，etc

Packing List

•Bar code scanner*1

•USB cable*1

•Instruction manual*1

•USB base station*1

LED Description

Set Up Step

The scanner has been paired with the base station, and set up already.

Step 1, Power on the scanner by pressing the button. The buzzer has a triple

beeps, the green light on the top of scanner will be on.

Step 2. Insert the USB base station into the USB port of computer. The USB

base station’s blue light will be on.

Step 3. Open notepad on computer and move cursor to the blank where

scanning output should be placed. Scanning results can be displayed on

computer then.

If the barcode does not displayed， please set up the scanner again according

to the following steps.

Step 1. Unplug the USB base station and plug it in again

Step 2. Within 30 seconds, scan these codes in order.

1. Resrore default

2. Match

3. Instant upload mode

4. USB_HID

Step 3. Open Word on computer, move cursor to the blank, scan a barcode to

see if it can be uploaded.

FAQs:

Q1.If i scan a product barcode, will it include the name of the product in

the file automatically?

Answer：

The scanner works like a keyboard. The scanner does not interpret what the

barcode is, it just "types" out a string of alphabet numeric characters that the

barcode represents.

it's up to the database software you are using to interpret what that string of

characters means. Once you acquire the barcodes, you have to correlate them

to something more meaningful by either purchasing a software service that will

interpret the barcode and relate it to a product, or you can use your own

internal inventory system to assign the barcodes to specific products.

After creating the relationship between your barcode and the corresponded

information, when you enter the barcode into the software by the scanner,your

software will look up the barcode and then output the related information of

your product.

Q2. Why does scanner not read the barcode exactly. When I use the

scanner to read a barcode of an item, I get a different result from the

barcode itself.

If that is not your case, please send us a clear picture of the barcode and the

result you get, our customer service will help you to solve the problem.

Example 1, There are two separate barcodes together. It scanned the first 12

digits in the barcode but not the last five.

Solution： Please scan the code”UPC/EAN extra code-ON”on page 30.

Example 2, The original barcode is “ abc12345 ” ， the scanning result is

“+A+B+C+D12345”，the scanner put “+” between character.

Solution：Please scan the code “Code 39 FULL ASCII-On”on page 33.

Q3. Some barcodes can not be read, why?

Answer：

A. Incomplete and unclear barcodes might not be read.

B. It is possible that the setting is off by default for some barcode types which

are not commonly used. You need to activate a specific barcode type to get it

working.

Please feel free to contact our Customer Service Team for further assistance if

you don't know the exact type of barcode that you are referring to.

Q4.Is there any barcodes to remove auto-enter after every scanning?

Answer: To remove the auto-enter, please read the code”Disable end

character”on page 22.

Q5. How to add Tab?

Answer: To add Tab, please read the code”Add tab”on page 22.

Q6. Can the scanner send two enter after every scanning?

Answer:

To add two enter, please read these codes in order. (on page 39-35)

“Insert character” (on page 39)

“All barcode type” (on page 39)

“Data group 1” (on page 41)

“After barcode” (on page 42)

“013 CR/ENTER” (on page 49)

“Save settings” (on page 43)

Q7. Is there a way to make the scanner work with a white print on a black

background?

Answer: To set the scanner to read white bar code on black ground， please

scan the code “White in black background - On”on page 28, 37, 38.

Q8. Is there a way to program the scanner to show the special characters

like <RS>、 <GS> or <EOT> when scanning?

Answer: Please contact us at Email: [email protected] , send us the characters

you want to display, and our customer service team will help you.

Troubleshooting

Problem

Possible Reason

Solution

Insert the USB base

station into the PC‘s

USB port, the base

station’s blue led 3

is flashing all the

time.

No driver in the

computer.

Update USB driver

The USB port is broken.

Connect the base station

to another computer to

see it works.

The base station or the

cable is broken.

replacement.

Put the scanner on

the base station ，

the green led 2 does

not turn on.

bad contact of electrode.

replacement.

Power on the

scanner, the buzzer

does not beep, the

green light on the

top of scanner does

not turn on, the red

scanning laser does

not show up.

The battery run out.

Charge the scanner

The scanner can not

hold the charge.

The PC’s USB port is

broken.

Connect the base station

to another USB port for

charging.

The base station or USB

cable is broken.

replacement

Power on the

scanner, the buzzer

beeps, the green

light on the top of

scanner will be on,

the red scanning

laser does not show

up or become a dot.

The laser head is broken.

replacement

Scanner and USB

base station are all in

good condition. But

the barcode can not

be sent to computer.

The scanner failed to

match the USB base

station.

Unplug the base station

and plug it in to PC’s

USB port， within 30

seconds scan the

following codes in

order:

“Resrore default”

“match”

“instantly upload

mode”“USB_HID”

The scanner was set to

storage mode，scanned

data will be kept in the bu

ﬀer of scanner

The scanner was set to

USB virtual com.

Optional Function settings

Settings of the bar code scanner can be changed by scanning the setup bar

codes included in this manual.

1. Pairing Mode Setting (for wireless mode only)

1.1 One scanner to one base：

One scanner only transmits bar code to one base.

Pairing operation:

Plug the base into your computer ,scan the code "match " to pair the scanner

with the base

Match

Pairing indication:

（1）If the pairing succeeds, the buzzer beeps "DI da""di di di"

（2） If the pairing failed, the buzzer beeps "DI---en"

NOTE：30 seconds after the base is inserted, the scanner cannot match the

base.

If the pairing failed, please unplug the base and plug it again, then scan the

code "match”.

Several units can work independently with different computers in the same

area. They won't interface with each other during work.

If you want to use them on multiple computers, each with own scanner and

base. Please follow the steps.

（1）Plug the base A into PC’s USB port.

（2）Scan the code“match”using scanner A to pair the scanner A with the base

（3）30 seconds after the base A is plugged , plug the base B into Another

PC’s USB port.

（4）Scan the code “match”using scanner B to pair the scanner B with the base

......

Match

1.2. Max.32 Scanner - to - One base

Multiple scanners transmit barcode to one base. One base can connect to

32 scanners at most.

Pairing operation:

（1）Plug the base A into PC‘s USB port

（2）Scan the code“match”using scanner A to pair the scanner A with the base

（3）Unplug the base A and plug it to PC‘s USB port again

（4）Scan the code “match”using scanner B to pair the scanner B with the base

...

Match

2. Upload Mode Setting

1.1. Instant Upload Mode

Read barcodes and upload it straight to the file you have opened.

** To set the scanner to upload barcode instantly, scan the following code:

Instant upload mode

Scanning indication:

(1) The buzzer rang "DI" when the barcode is uploaded successfully.

(2) The buzzer rang a slow "DI---en" when the barcode can not be uploaded.

If some character are mixed up, please set the scanner to lower transmission

speed.

The transmission speed between every character can be changed by scanning

the following code. The higher the value, the slower the speed is.

Speed 00 (default)

Speed 15

Speed 30

Speed 40

Speed 50

Speed 60

1.2. Storage Mode

Read bar codes and store the bar codes in scanner’s own memory. You can

upload the data to computer in batches when you need them. Internal

storage saves up to 10,000 bar codes.

Note: In storage mode, the bar code will be stored and will not come up on

your computer instantly. The bar code comes up on your computer only when

you scan the settings code "upload data".

** To convert scanner from "instant upload mode" to "storage mode", scan

the following bar code “Storage mode“.

Storage mode

** To upload data from memory, put the cursor in the blank, and then scan

the “Upload Data” barcode, it will upload all the stored barcode at a time.

Upload data

** To show total number of stored bar code, put the cursor in the blank, and

then scan the “Show total storage”bar code. It will out put

“TotalCounters： xx”.

Show total storage

** Scan the barcode “Clear data”to clear all the stored barcode. (for storage

mode only)

Clear data

Scanning indication:

(1) The buzzer rang a fast "DI-en" when the barcode is saved successfully in the

built-in memory of the scanner

(2)The buzzer rang a slow "DI---en" when the barcode can not be saved in the

built-in memory of the scanner. The space of memory is not enough and

cannot store any more barcodes. Please upload the saved barcode by scanning

the code "Upload Data" and then clear the saved barcode by scanning code

"zero clearing".

Note: In storage mode, the transmission speed between every barcode can

be changed by scanning the following code. If some barcodes are missing,

please set the scanner to lower transmission speed.

The higher the value, the slower the speed is.

Speed 000

Speed 001

Speed 002

Speed 040

Speed 050

Speed 060

3. Scanning Mode Setting

Three kinds of scanning modes are supported.

3.1. Manual Trigger mode (default) :

Press the trigger, the scanner will emit light and read the barcode. Release the

trigger, the scanner will stop reading barcode and the light will go off.

** Scan the following codes to set the scanner to Manual trigger mode .

Manual trigger mode (default)

3.2. Continuous Scanning Mode

There’s no need to click the trigger in this mode. The red light of the scanner

will be on at a certain frequency.

The red scanning light will go off once the scanner scans barcode successfully

and the scanner will enter into next scanning automatically after a intermittent

time . And the red scanning light of the scanner will be on again once the

waiting time passes

** Scan the following codes to set the scanner to Continuous Scanning Mode.

Continuous Scanning Mode

3.3. Auto-induction Mode

There’s no need to click the trigger under the Auto-induction Mode. Users just

need to move the barcodes in front of the scanner. A red light band will show

up to read the barcode.

The red light band will go off once the scanner scans barcode successfully or

pre-set timeout expires.

** Scan the following codes to set the scanner to Auto-induction Mode .

Auto-induction Mode

** Scan one of the following codes to select the induction sensitivity.

Note： In Auto-induction Mode. It will be better to set the scanner out to be

longer stand-by time interval. Please refer to the instruction on page 25.

High sensitivity (default)

Medium sensitivity

Low sensitivity

Table of contents

REALINN RL6100-2D User manual

Popular Barcode Reader manuals by other brands