Red Epic Epic User manual

EPIC |SCARLET |V5.1
DRAGON |MYSTERIUM-X
RED.COM
RED DSMC
OPERATION GUIDE

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |2
TABLE OF CONTENTS
Disclaimer 4
Copyright Notice 4
Trademark Disclaimer 4
Compliance Statements 4
Safety Instructions 6
Chapter 1: DSMC Overview 7
DRAGON Sensor 7
MYSTERIUM-X®Sensor 7
Image Processing 8
HDRx 8
Magic Motion 9
Audio Recording 9
Microphone Level Analog Inputs 9
Line Level Analog Inputs 9
Video Monitoring Outputs 10
Lens Mounts 11
REDMOTE 11
SMPTE Timecode 11
Additional Resources 11
Chapter 2: Components and Modules 12
Brain 12
Side SSD Modules 14
DSMC SIDE HANDLE 17
DSMC Modules 18
REDMOTE 30
DSMC Displays 31
Chapter 3: Power the DSMC 34
Power Consumption 34
Power Draw 34
Power Sources 34
Power Status 41
Power Up 41
Power Down 42
Chapter 4: Graphical User Interface 43
RED LCD, Touchscreen LCD, BOMB EVF, External
Monitors 43
DSMC SIDE HANDLE 47
REDMOTE 47
Navigate Graphical User Interface 48
Chapter 5: Basic Menus 49
Access Advanced Menus from Basic Menus 49
Edit List Feature 49
Frame Rate (FPS) 49
ISO (Sensitivity) 49
F Stop 50
Exposure 50
White Balance 51
Resolution 51
REDCODE 51
Chapter 6: Advanced Menus 56
Settings Menu 56
Media Menu 95
Playback 95
Power 96
HDR Menu 97
Focus Menu 98
Presets 103
Chapter 7: Upgrade DSMC Firmware 106
Verify Current Camera Firmware 106
Upgrade Procedure 106
Chapter 8: Manage Digital Media 108
Overview 108
Format Media 108
Metadata 109
Clip Naming Conventions 110
Media Capacity Remaining Status 110
Eject Media from Camera (Unmount) 110
Offload Media to your Computer 111
Erase Media 111
Media Menu 112
Chapter 9: Audio Subsystem 114
Audio Format 114
Channel Setup 114
Source Selection 114
Channel Modes 114
Audio Recording 115
Peak Meter 115
Data Path 115
HD-SDI/HDMI Embedded Audio 115
Audio During Playback 117
Chapter 10: REDMOTE Operation 118
Control, Connectors and Display 118
Operation 120
Internal Battery 124
Upgrade REDMOTE Firmware 125
Appendix A: Input/Output Connectors 129
Camera Brain Front 129
Camera Brain Rear 131
Side SSD Module Connectors 137
REDMOTE 138
Appendix B: Supported Lenses 139
DSMC Canon Mount and DSMC Canon MOTION
MOUNT Electronically Supported Lenses 139
DSMC Nikon Mount Electronically Supported Lenses
141
DSMC Leica-M Mount Lenses 141
Appendix C: Default Key Functions 142
Appendix D: 3D Setup and Operation 145
Overview 145
Camera Setup 145
Clip Naming Conventions 145
Connecting Cameras 146
Operation 146
Appendix E: Post-Production 147
Monitoring 147
REDCINE-X®PRO 147
Appendix F: DSMC Maintenance 148
Cleaning 148

RED DSMC OPERATION GUIDE
COPYRIGHT © 2013 RED.COM, INC 955-0020_V5.1, REV-D |3
Back Focus Adjustment 149
Appendix G: Troubleshoot Your DSMC 151
No Media Attached 151
Recording Halted: Record Error–Shutdown 151
Preset Could Not Be Applied 151
Camera Cannot Be Paired to REDMOTE 151
Cannot See Menus on LCD Touchscreen 151
Appendix H: Technical Specifications 152
EPIC DRAGON 152
EPIC MYSTERIUM-X 154
SCARLET DRAGON 156
SCARLET MYSTERIUM-X 158
DSMC Brain Dimensions 160
Appendix I: Menu Map 165

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |4
COMPLIANCE STATEMENTS
INDUSTRIAL CANADA EMISSION COMPLIANCE STATEMENTS
This device complies with Industry Canada license-exempt RSS
standards RSS 139 and RSS 210. Operation is subject to the follow-
ing two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Le présent appareil est conforme aux CNR d’Industrie Canada ap-
plicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est sus-
ceptible d’en compromettre le fonctionnement.Cet appareil numéri-
que de la classe B est conforme à la norme NMB-003 du Canada.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATE-
MENTS
This equipment has been tested and found to
comply with the limits for a Class B digital de-
vice, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reason-
able protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio fre-
quency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-ap-
proved equipment or unshielded cables is likely to result in interfer-
ence to radio and TV reception. The user is cautioned that changes
and modifications made to the equipment without the approval of
manufacturer could void the users authority to operate this equip-
ment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operations subjected to the following two conditions (1) this device
may not cause harmful interference, and (2) this device must accept
any interference received, including that may cause undesirable in-
terference.
CAUTION: Exposure to Radio Frequency Radia-
tion.
The device shall be used in such a manner that the potential for hu-
man contact is minimized
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 cm between
the radiator and your body.
CAUTION: Regulations of the FCC and FAA
prohibit airborne operation of radio-frequency
wireless devices because there signals could
interfere with critical aircraft instruments.
CAUTION: If the device is changes or modified
without permission from RED, the user may
void his or her authority to operate the equip-
ment.
AUSTRALIA AND NEW ZEALAND STATEMENTS
RED declares that the radio equipment described in this document
comply with the following international standards.
IEC 60065 - Product Safety
ETSI EN 300 328 - Technical requirement for radio equipment
RED declares digital devices described in this document comply
with the following Australian and New Zealand standards.
AS/NZS CISPR 22 – Electromagnetic Interference
AS/NZS 61000.3.2– Power Line Harmonics
AS/NZS 61000.3.3 – Power Line Flicker
DISCLAIMER
RED has made every effort to provide clear and accurate informa-
tion in these installation instructions, which are provided solely for
the user’s information. While thought to be accurate, the informa-
tion in this document is provided strictly “as is” and RED will not
be held responsible for issues arising from typographical errors or
user’s interpretation of the language used herein that is different
from that intended by RED. All safety and general information is
subject to change as a result of changes in local, federal or other
applicable laws.
RED reserves the right to revise this document and make changes
from time to time in the content hereof without obligation to notify
any person of such revisions or changes. In no event shall RED, its
employees or authorized agents be liable to you for any damages
or losses, direct or indirect, arising from the use of any technical or
operational information contained in this document.
For comments or questions about content in this Operation Guide,
please send a detailed e-mail to [email protected].
COPYRIGHT NOTICE
COPYRIGHT© 2013 RED.COM, INC.
All trademarks, trade names, logos, icons, images, written material,
code, and product names used in association with the accompa-
nying product are the copyrights, trademarks or other intellectual
property owned and controlled exclusively by RED.COM, INC.
TRADEMARK DISCLAIMER
All other company, brand and product names are trademarks or reg-
istered trademarks of their respective holders. RED has no affiliation
to, is not associated or sponsored with, and has no express rights
in third-party trademarks. Distagon is a registered trademark of Carl
Zeiz, Inc. Leica is a regestered trademark of BV Corporation Nether-
lands. Nikkor, is a registered trademark of Nikon Corporation.

RED DSMC OPERATION GUIDE
COPYRIGHT © 2013 RED.COM, INC 955-0020_V5.1, REV-D |5
JAPAN STATEMENTS
This is a Class B product based on the
standard of the Voluntary Control Council
for Interference (VCCI) for information tech-
nology equipment. If this equipment is used
near a radio or television receiver in a do-
mestic environment, it may cause radio in-
terference. Install and use the equipment
according to the instruction manual.
EUROPEAN UNION COMPLIANCE STATEMENTS
RED declares that the radio
equipment described in this
document comply with the
R&TTE Directive (1999/5/
EC) issued by the Commis-
sion of the European Com-
munity.
Compliance with this directive implies conformity to the following
European Norms (in brackets are the equivalent international stan-
dards).
EN 60065 (IEC 60065) – Product Safety
ETSI EN 300 328 Technical requirement for radio equipment
ETSI EN 301 489 General EMC requirements for radio equip-
ment.
INFORMATION
Products with the CE marking comply with the EMC Directive
(2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued
by the Commission of the European Community. Compliance with
these directives implies conformity to the following European Prod-
uct Family Standards.
EN 55022 (CISPR 22) – Electromagnetic Interference
EN 55024-1 (CISPR 24) – Electromagnetic Immunity
EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics
EN 61000-3-3 (IEC610000) – Power Line Flicker
EN 60065 (IEC60065) – Product Safety
USAGE RESTRICTIONS FOR PRODUCTS THAT INCORPORATE
REDLINK
Products that fall into this category are denoted
by inclusion of the Class 2 identifier symbol (ex-
clamation mark in a circle) accompanying the CE
Mark on the products regulatory label, example
to the left.
FRANCE
Usage Restrictions - Geographic Area Where Restriction Applies :
France
For mainland France
2.400 - 2.4835 GHz (Channels 1-16) authorized for indoor use
2.400 -2.454 GHz (Channels 1-10) authorized for outdoor use
Restrictions d’utilisation - Zone géographique où les restrictions
s’appliquent : France
Pour la France métropolitaine
2.400 - 2.4835 GHz (Canaux 1 à 16) autorisé en usage intérieur
2.400 -2.454 GHz (canaux 1 à 10) autorisé en usage extérieur
NORWAY
This subsection does not apply for the geographical area within a
radius of 20 km from the centre of Ny-Ålesund
Dette gjelder ikke for det geografiske området innenfor en radius av
20 km fra sentrum av Ny-Ålesund
The Waste Electrical and Electronic Equip-
ment (WEEE) mark applies only to countries
within the European Union (EU) and Norway.
This symbol on the product and accompany-
ing documents means that used electrical
and electronic products should not be mixed
with general household waste. For proper
treatment, recovery and recycling, please
take this product to designated collection
points where it will be accepted free of
charge. Alternatively, in some countries you
may be able to return your products to your
local retailer upon purchase of an equivalent
new product.
Disposing of this product correctly will help save valuable resources
and prevent any potential negative effects on human health and the
environment, which could otherwise arise from inappropriate waste
handling. Please contact your local authority for further details of
your nearest designated collection point. Penalties may be appli-
cable for incorrect disposal of this waste, in accordance with you
national legislation.
For business users in the European Union, if you wish to discard
electrical and electronic equipment, please contact your dealer or
supplier for further information.
RESPONSIBLE PARTY:
RED Digital Cinema
34 Parker
Irvine, CA 92618
USA

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |6
SAFETY INSTRUCTIONS
DO NOT USE the camera or accessories near water. Avoid ex-
posing your camera to moisture. The unit is not waterproof,
so contact with water could cause permanent damage to the
unit as well as electric shock and serious injury to the user. DO
NOT USE the camera in the rain or under other conditions with
high moisture without appropriate protection, and immediately
remove power source if camera or accessories are exposed to
moisture.
WARNING: To reduce the risk of fire or elec-
tric shock, do not expose the camera to
rain or moisture.
Do NOT expose the DSMC to laser beams, as laser beams may
damage the sensor.
DO NOT expose your camera to excessive vibration or impact
(shock). Be careful not to drop your camera. Internal mecha-
nisms may be damaged by severe shock. Mechanical alignment
of optical elements may be affected by excessive vibration.
ELECTROMAGNETIC INTERFERENCE: The use of devices us-
ing radio or other communication waves may result in the mal-
function or interference with the unit and/or with audio and
video signals.
Clean only using a dry cloth. When cleaning your camera, re-
member that it is not waterproof and moisture can damage
electronic circuitry. DO NOT rinse or immerse any element of
the camera, lens or other accessory, keep them dry at all times.
DO NOT USE soaps, detergents, ammonia, alkaline cleaners,
and abrasive cleaning compounds or solvents. These sub-
stances may damage lens coatings and electronic circuitry.
Maintain sufficient ventilation—DO NOT block any ventilation
openings or obstruct cooling fan airflow.
CAUTION: Proper camera ventilation re-
quires a minimum 1/2” (1,25cm) clearance
between the camera ventilation openings
and external surfaces. Verify that objects
that can block the fan intake and ex-
haust ports do not impede airflow. Failure
to permit adequate airflow may result in
overheating of the camera, degraded op-
eration and in extreme situations, damage
to the camera.
DO NOT operate or store near any heat sources such as radia-
tors, heat registers, stoves, or any other apparatus that pro-
duce heat. Store in a protected, level and ventilated place.
Avoid exposure to temperature extremes, damp, severe vibra-
tion, strong magnetic fields, direct sunlight or local heat sourc-
es during storage. Remove any batteries from the camera be-
fore storage. Recommended storage and usage temperatures
for your camera, lenses and other accessories are:
‒Operating range: 0°C to +40°C (32°F to 104°F)
‒Storage range: -20°C to +50°C (-4°F to 122°F)
If there are any performance issues with your camera or acces-
sories when operating within this temperature range, please file
a support ticket on support.red.com.
The DSMC SIDE HANDLE, SIDE SSD Module, Rear Modules
and Lens Mount are NOT HOT SWAPPABLE, meaning you can-
not remove or install them while the camera is powered on. Be-
fore installing or removing any of these accessories, you MUST
power down the camera. Failure to do so may result in damage
to the accessory and/or camera brain that will not be covered
under warranty.
Do not bypass the third prong of the grounding-type plug on
the power cord of the AC Power Adapter. A grounding-type
plug has two blades and a third “grounding” prong. The third
prong is provided for your safety. A grounding-type plug shall
be connected to an outlet with a protective earthen connec-
tion. If the grounding-type plug does not fit into your outlet,
do not attempt to modify the plug or outlet, consult a qualified
electrician.
Protect all power cords from being pinched, walked on or
driven over by a vehicle. Replace any power cords suspected
of sustaining damage due to crushing or other forms physical
damage.
CAUTION: The power cord plug for the AC
Power Adapter is used as the power dis-
connect. To disconnect all power from the
AC Power Adapter, unplug the power cord
plug from the wall outlet. During use, the
power cord plug should remain easily ac-
cessible at all times.
Lithium Ion batteries may be subject to special handling re-
quirements pursuant to federal and local laws. Please refer to
specific shipping instructions included with your battery re-
garding proper transport of your battery. Do not handle your
battery if it is damaged or leaking. Disposal of batteries must
be in accordance with local environmental regulations. For
example, California law requires that all rechargeable batter-
ies must be recycled by an authorized recycle center. Storing
batteries fully charged or in high temperature, conditions may
permanently reduce the life of the battery. Available battery
capacity may also be temporarily lessened after storage in low
temperature conditions.
WARNING: Do not expose the battery to ex-
cessive heat.
WARNING: Danger of explosion if an incor-
rect battery is charged with the RED Char-
ger or is used to power the camera and
accessories. Replace only with the same
or equivalent type battery.
CAUTION: Refer all service and repair to
qualified RED service personnel. To reduce
the risk of electric shock, and damage to
the camera or accessories, DO NOT at-
tempt to perform any servicing other than
any procedures that are recommended in
the operating instructions.

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |7
Congratulations on your purchase of one of the following RED DSMC®Digital Still and Motion Cameras:
EPIC-M RED DRAGON (CARBON FIBER)
EPIC-M
EPIC-X
SCARLET-X
Each RED DSMC BRAIN is equipped with a DRAGON or MYSTERIUM-X sensor.
The RED family of Digital Still and Motion Cameras (DSMC) provide high performance digital imaging over a
wide range of frame rates and optical formats including Super 35mm/APS-H.
DRAGON SENSOR
The new 6K RED DRAGON™ sensor allows you to capture over nine (9) times more resolution than standard
HD. The result is unrivaled detail and impressive native exposure eclipse 35mm film in both latitude and image
density.
The DRAGON sensor is a model for image innovation, leading the way in the evolution of digital cinema technol-
ogy. Boasting industry-leading specs in resolution, frame capture, dynamic range, and color science, the RED
DRAGON sensor raises the bar for digital still and motion cameras, again.
MYSTERIUM-X®SENSOR
The MYSTERIUM-X sensor is specifically designed for use with the RED DSMC BRAIN, and in the EPIC it pro-
vides variable frame rate imaging at up to 95 FPS at 5K FF resolution, and up to 400 FPS at 1K WS resolution.
Native color balance for the MYSTERIUM-X sensor is 5,000 KELVIN, but it may be electronically compensated
for any color temperature in the range 1,700 to 10,000 KELVIN. White balance preset values include Tungsten
(3200K) and Daylight (5600K) light sources. The camera may also calculate a color neutralizing White Balance
value on demand by imaging on a standard white or 18% gray card.
The MYSTERIUM-X sensor includes high precision analog to digital conversion, capable of delivering up to 13.5
stops of dynamic range with daylight light sources over a camera sensitivity rating of 320-800 ISO. In HDR
EPIC Digital Still
and Motion
Cameras (DSMC)
01 DSMC
OVERVIEW

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |8
mode, dynamic range can be extended to approximately 18 stops.
IMAGE PROCESSING
The digital image received from the sensor is formatted as a pixel defect corrected (but in all other aspects
unprocessed) 16-bit per pixel RAW data frame.
Each RAW frame or sequence of RAW frames in a clip is compressed using proprietary wavelet based RED-
CODE®RAW compression, then stored to a digital media magazine such as the REDMAG™1.8” SSD.
When recorded, the RAW data is independent of any RGB domain color processing such as ISO, White Balance
or other RGB color space adjustments made by the camera operator. These parameters are saved with the
RAW data as reference metadata; that is, color is not burned into the recorded RAW data.
This recording technique permits RGB color processing choices to be deferred to post-production or to be ad-
justed in the field to help a director visualize alternative color treatments, without affecting the recorded RAW
data’s image quality or dynamic range.
The camera’s monitoring path converts RAW sensor data to a white balanced 12-bit depth 1920 x 1080 pixel
RGB 4:4:4 video signal. This signal may be modified using ISO, White Balance or other RGB color space ad-
justments as desired, and is then scaled and gamma-corrected to provide VIEWFINDER, HD-SDI, and HDMI
monitor outputs at 10-bit depth in 4:2:2 YCC or 8-bit depth in 4:4:4 RGB.
Frame guides and other camera data may be added as desired to one or more of the outputs.
NOTE: The REDCINE-X®PRO software can create and export .RMD “Look” files which may then be imported as
camera monitor path color processing presets. This information is stored as reference metadata, so that this
color processing choice can be the default value used in post-production. For more information about Look
files, go to “Looks” on page 105.
HDRX
HDRx is an option for extending dynamic range up to 6 stops over the base dynamic range offered by the cam-
era. When enabled, HDRx simultaneously shoots two images of identical resolution and frame rate—a normally
exposed primary track (A-track), and an underexposed secondary track (X-track) whose exposure value reflects
the additional stops of highlight protection desired.
For example, if you select an HDR value of +2 and your primary track exposure is 1/48 sec, the secondary
track exposure will be 2 stops under, or 1/192 sec. The ISO and aperture remain the same for both exposures.
During acquisition and recording, the two tracks are “motion-conjoined”, meaning there is no gap in time be-
tween the two exposures. This is very important to note because if these were traditional alternating exposures,
there would be a time gap between the two tracks that would show up as an undesirable motion artifact. Both
tracks (A and X) are stored in a single .R3D®file.
Since there are two exposures in HDRx mode, the camera is recording double the amount of frames each sec-
ond. For example, when shooting at 24 FPS, the camera is recording two 24 FPS tracks, which is the data rate
equivalent of 48 FPS; however, after combining the A and X tracks in post-production, you will see only one 24
FPS blended image sequence.
HDRx provides multiple options for exploitation in post-production.
Blend the two tracks in post tools like REDCINE-X PRO or any other application that supports the SDK to
create Magic Motion™. This blending of the two tracks comes with a slider so that you can decide just how
much of each track you want to use. A preview window shows you the combined result of your selection,
or you can view each track individually.
Combine the two tracks using MNMB (More Normal Motion Blur). MNMB is designed to emulate the motion
of a traditional camera with full motion blur. This is a tool created by The Foundry that uses a new motion
estimation algorithm designed specifically for HDRx. The shorter exposure (sharper image) is blended to
match the motion blur of the normal exposure. Again, a preview window shows the combined result of your
selection, or you can view each track individually.
Use the X-track data for motion tracking, then combine the X-track with the A-track, or just motion stabilize
the A-track using the motion analysis data extracted from the X-track.

RED DSMC OPERATION GUIDE
COPYRIGHT © 2013 RED.COM, INC 955-0020_V5.1, REV-D |9
Export to EXR file format to get a multi-view EXR with both exposures (like a stereo EXR).
NOTE: If you ignore the X-track data, you will have a standard exposure with up to 13.5 stops of dynamic range
just as if you had not enabled HDRx. For this reason, we encourage the A-track exposure to be “normal” as
it provides the most options. If you are tempted to shoot “over-under”, you are then fully committed to using
HDRx and your post-production options are reduced.
NOTE: When recording in HDRx mode, the camera records twice as many frames per second so that the maxi-
mum frame rate or minimum REDCODE ratio, and the maximum record time on your media will be cut in half.
NOTE: HDRx mode can be used with sensor syncing.
MAGIC MOTION
Shooting at 24 FPS and with an 180 degree (1/48 sec) shutter on a film or digital camera may create an opti-
cal illusion we are familiar with, however it is not really the way the eye sees motion. To understand this, ask
someone to stand in front of you and swing their arm over their head from one side to the other. What you would
observe in the recording is a constant motion blur until the arm stopped. What your eye sees though is both
motion blur AND a sharper reference to the arm and hand all along the motion path. MAGIC MOTION provides
such a combination of motion blur (A-track) and a sharper reference (X-track), with the bonus of extreme dy-
namic range not available with any other motion capture camera system.
AUDIO RECORDING
The RED DSMC camera can record up to two discreet channels of microphone level uncompressed 24-bit, 48
KHz audio (four channels of microphone level or line level audio inputs when equipped with a PRO I/O MOD-
ULE), that are synchronized with video and timecode to a REDMAG 1.8” SSD.
Input signals are routed via a high quality pre-amplifier and soft clip analog limiter in order to achieve the de-
sired audio reference/recording level and maximize dynamic range.
To assist with audio reference level setup, the camera provides a color-coded Audio Level Meter in the graphi-
cal user interface. Meter range is -36 dBu to +20 dBu (-56 dBFS to 0 dBFS) with audio input type, reference
level and audio input clipping indicators.
Audio monitor output options include a 2-channel headphone output on the DSMC BRAIN and 2-channel line
level analog outputs from the optional PRO I/O MODULE, plus 2-channel and 4-channel 24-bit 48 KHz uncom-
pressed digital audio embedded in the HD-SDI and HDMI outputs.
MICROPHONE LEVEL ANALOG INPUTS
The recording level of a Microphone input is affected by the sensitivity of the microphone and the Gain setting
of the camera’s pre-amplifier. Available pre-amplifier range is +30 dB to +60 dB. The camera operator should
choose a Gain value that aligns the input signal to the 0 dBu reference line drawn on the camera’s Audio Level
Meter (or the 0 VU reference line if operating at that level).
This setting provides up to 30 dB of input signal headroom above reference 0 dBu level before clipping (up to
26 dB above 0 VU reference level) and maximizes the signal to noise ratio of the 24-bit digital recording.
LINE LEVEL ANALOG INPUTS
The recording level of a Line input is affected only by the signal provided by the field production sound mixer
or other external line level source. The sound mixer operator should choose a mixer output level that aligns a
reference tone signal to the 0 dBu (-20 dBFS) reference mark drawn on the camera’s Audio Level Meter, or if
using 0 VU as reference level, a mixer output level that aligns a reference tone signal to the 0 VU (-16 dBFS)
reference mark.
This setting provides up to 24 dB of input signal headroom above reference 0 dBu level before clipping (up to
20 dB above 0 VU reference level) and maximizes the signal to noise ratio of the 24-bit digital recording.

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |10
VIDEO MONITORING OUTPUTS
In its default configuration, the RED DSMC camera can simultaneously support one VIEWFINDER output (suit-
able for use by a BOMB EVF®, or RED LCD) plus one PROGRAM output and one PREVIEW output (suitable for
use by HDMI or HD-SDI monitors). The various monitor outputs can support a set of overlay graphics including
camera GUI, timecode, clip name and framing guides; the specific overlay graphics for each type of output is
user configurable.
The default VIEWFINDER output is the EVF/LCD connector located on the front face of the SIDE SSD MODULE.
If neither of these is connected, the VIEWFINDER output can be transferred to either the HDMI output or the
HD-SDI output of the DSMC BRAIN.
All monitors are able to display a variety of features, including:
Surround View™, which is an additional lookaround area, visible outside of the recorded image.
Frame Guides, showing common film presentation and television aspects such as 2.40:1 and 16:9.
Focus, aided by high display resolution, 1:1 Focus Check function, and false color overlay.
Exposure, aided by dual zebra indicators, RAW “traffic lights”, and RGB histogram.
System information including current frame rate, ISO rating, shutter speed, color temperature, record reso-
lution, record quality, clip name, timecode value, and the remaining battery and media capacity.
BOMB EVF (LCOS) AND BOMB EVF (OLED)
The BOMB EVF (LCOS) and BOMB EVF (OLED) are high-definition, lightweight viewfinders that align quality
performance with compact form factor.
For applications where use of an attached RED EVF or RED LCD is not desired, such as when working on a
crane, the VIEWFINDER/MENU output can be transferred to the HD-SDI or HDMI outputs, supporting remote
camera monitoring up to 200 ft away.
RED TOUCH LCD
The RED TOUCH LCD pixel progressive scan color display allows you to view your image and navigate through
menu settings using touchscreen functionality.
For applications where use of an attached RED EVF or RED LCD is not desired, such as when working on a
crane, the VIEWFINDER/MENU output can be transferred to the HD-SDI or HDMI outputs, supporting remote
camera monitoring up to 200 ft away.
NOTE: DO NOT USE the RED LCD as a handle to lift or carry the DSMC. Damage to the RED LCD or other com-
ponents of the DSMC system caused by using the RED LCD as a handle is not covered under warranty.
NOTE: The RED LCD swivel axis has a total range of adjustment of approximately 360˚ (180˚ clockwise or coun-
terclockwise from the nominal “rear-facing” display orientation). The range of adjustment for the tilt axis is ap-
proximately 180˚. At the end of the adjustment range are internal “hard stops” for both axes. Once the swivel
or tilt hard stops have been reached, IMMEDIATELY STOP APPLYING FORCE TO THE LCD. Continuing to
apply force after reaching the internal stops may damage the friction hinge. Damage to the RED LCD or other
components of the DSMC system caused by using excessive force to rotate the RED LCD is not covered under
warranty.
HD-SDI
A 720p or 1080p progressive scan output suitable for monitoring or recording to an external VTR or DDR de-
vice. May be configured for 10-bit LIN (VIDEO) or 10-bit LOG (FILM) encoded data.
HDMI
A 720p or 1080p progressive scan output suitable for monitoring via a PC monitor or most HDTV displays.

RED DSMC OPERATION GUIDE
COPYRIGHT © 2013 RED.COM, INC 955-0020_V5.1, REV-D |11
LENS MOUNTS
The RED DSMC comes with a DSMC TI PL MOUNT, and may be configured with mounts and 19 mm rods to
accommodate most cinematography lenses, matte boxes, and follow focus systems. Adaptors for 15 mm offset
studio and 15 mm lightweight rods are also available.
Other lens mounts, including the DSMC CANON MOUNT, are available, permitting the use of Canon EF and
EF-S photographic lenses. The DSMC CANON MOUNT can report lens iris, focus, and zoom data when mated
to an electronically supported lens. In addition, iris and manual or auto-focus settings may be controlled from
the camera.
Lens mounts can be changed out in the field; however, it is highly recommended that this be performed in a
dust-free environment, as the optical path will be exposed to the elements during this process.
REDMOTE
The REDMOTE is a camera control unit for RED DSMCs that attaches to the rear of the DSMC BRAIN or rear-
most expansion module. The REDMOTE may also be detached from the camera or rearmost module and pro-
vide wireless remote control of the camera over proprietary REDlink™protocol.
Whether attached or operating via wireless, REDMOTE supports all controls necessary to operate the camera,
including Record Start/Stop, Shutter Speed, White Balance, ISO, and programmable User Keys. A color LCD
displays critical camera parameters, including media and battery capacity, timecode and clip name, lens data
and exposure information.
The REDMOTE includes a rechargeable Li-Ion battery, which automatically re-charges when attached to the
camera or rearmost module. It may also be re-charged by connecting to a USB 2.0 based power source such
as a laptop or cell phone charger. Under typical operating conditions, the REDMOTE should operate for up to
8 hours without requiring a re-charge and support a wireless communication range of approximately 50 ft.
SMPTE TIMECODE
Time Code (TC) is a SMPTE timecode track that synchronizes to the camera’s high precision internal clock,
or if operated in Jam Sync mode, referencing an externally supplied SMPTE master timecode signal. TC is a
sequential code that is continuous from frame to frame, but is discontinuous from clip to clip.
Edge Code (EC) is a SMPTE timecode track that always starts at 1.00.00.00 on the first frame recorded to the
digital media. It is a sequential code that is continuous from frame to frame and also continuous from clip to
clip. EC is equivalent to RUN RECORD, which is commonly found on broadcast cameras.
Irrespective of the timecode mode selected, once recording starts the camera’s timecode counter will update at
the same instantaneous frame rate as the recording. This ensures that a valid SMPTE timecode value is created
for every frame in the clip, eliminating any timecode count jumps that could affect playback or editing.
If operating in Jam Sync mode referenced to an external timecode source, the clip’s master time reference point
is the first frame of the recorded clip.
ADDITIONAL RESOURCES
The following resources offer additional information about RED, the DSMC system, and the RED community:
RED.com: Check the official RED website for the latest information about RED products.
RED Learn Articles: RED offers in-depth technical articles about RED cameras, post-production, and digital
cinematography.
RED.com/downloads: Go to the RED Downloads page to download the latest firmware, operation guides,
and post-production software.
Support.red.com: Check the RED SUPPORT site for FAQs, or to file a support ticket.
Reduser.net: Discuss all things RED on the REDUSER third-party forum.
In-camera Help: Select the Help button on an in-camera screen to open up the help for that screen.

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |12
This section provides an overview of the DSMC components and modules.
WARNING: The DSMC SIDE HANDLE, SIDE SSD MODULE, rear modules and Lens Mount are NOT HOT SWAP-
PABLE, meaning you cannot remove or install them while the camera is powered on. Before installing or remov-
ing any of these accessories, you MUST power down the camera. Failure to do so may result in damage to the
accessory and/or camera brain that will not be covered under warranty.
BRAIN
EPIC Brain
02 COMPONENTS
AND MODULES

RED DSMC OPERATION GUIDE
COPYRIGHT © 2013 RED.COM, INC 955-0020_V5.1, REV-D |13
BRAIN LEDS
LED COLOR/FLASHING DESCRIPTION
Power Status LED
(PWR) Red Power present; camera off
Yellow Power present; camera booting
Green Power present; camera on
Green flashing Power present; running on battery
Yellow flashing Power present; 5–10 minutes of
battery time left
Red flashing Power present; less than 5 minutes
of battery time left
Record Status LED
(REC) Off No media present
Green Ready to record
Red Recording
Red slow flashing Recording; 25% media left
Red fast flashing Recording; 5% media left
Yellow Finalizing
Power Status LED (PWR)
and Record Status LED (REC) Both green flashing Firmware update in progress
Both red flashing Firmware update failing

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |14
SIDE SSD MODULES
RED offers the following side SSD modules:
RED MINI-MAG SIDE SSD
DSMC 1.8" SSD SIDE MODULE
WARNING: The RED MINI-MAG SIDE SSD and DSMC 1.8" SSD SIDE MODULE are NOT HOT SWAPPABLE,
meaning you cannot remove or install the modules while the camera is powered on. Before installing or remov-
ing the RED MINI-MAG SIDE SSD or DSMC 1.8" SSD SIDE MODULE, you MUST power down the camera.
Failure to do so may result in damage to the module or DSMC that will not be covered under warranty.
RED MINI-MAG SIDE SSD
The RED MINI-MAG SIDE SSD attaches to the DSMC so that you can mount a RED MINI-MAG to your camera.
The RED MINI-MAG SIDE SSD has the same EVF/LCD LEMO connector, user keys, and REC button as the
DSMC 1.8" SSD SIDE MODULE.
The RED MINI-MAG mounts to the RED MINI-MAG SIDE SSD.
REDMINI-MAGSIDESSD

RED DSMC OPERATION GUIDE
COPYRIGHT © 2013 RED.COM, INC 955-0020_V5.1, REV-D |15
DSMC 1.8" SSD SIDE MODULE
The DSMC 1.8" SSD SIDE MODULE attaches to the DSMC so that you can mount a REDMAG 1.8" SSD to your
camera. The DSMC 1.8" SSD SIDE MODULE has the same EVF/LCD LEMO connector, user keys, and REC
button as the RED MINI-MAG SIDE SSD.
The following SSDs mounts to the DSMC 1.8" SSD SIDE MODULE:
REDMAG 1.8" SSD (48GB)
REDMAG 1.8" SSD (64GB)
REDMAG 1.8" SSD (128GB)
REDMAG 1.8" SSD (256GB)
REDMAG 1.8" SSD (512GB)
SIDE SSD MODULE CONTROLS
The RED MINI-MAG SIDE SSD and DSMC 1.8" SSD SIDE MODULE have the control buttons described in the
tabled below.
CONTROL DESCRIPTION
User Key 1 Programmable key
User Key 1 + 2 Press: Eject Media
User Key 2 Programmable key
User Key 1 + 2 Press: Eject Media
REC button Programmable key
Full Press: Record Toggle
Half Press: AF Start
DSMC 1.8" SSD SIDE MODULE
(Rear and Front)

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |16
SIDE SSD MODULE LEDS
The RED MINI-MAG SIDE SSD and DSMC 1.8" SSD SIDE MODULE have the LED described in the tabled be-
low.
LED COLOR/FLASHING DESCRIPTION
Media Indicator LED Off No media present
Green Ready to record
Red Recording
Red slow flashing Recording; 25% media left
Red fast flashing Recording; 5% media left
Yellow Finalizing
Yellow flashing Accessing media (for example,
when formatting)

RED DSMC OPERATION GUIDE
COPYRIGHT © 2013 RED.COM, INC 955-0020_V5.1, REV-D |17
DSMC SIDE HANDLE
The DSMC SIDE HANDLE provides the following:
A battery compartment for one REDVOLT battery.
An LCD display that shows key camera parameter values.
Many programmable user keys and buttons. For a full list of all DSMC SIDE HANDLE user keys and their
default actions, go to “Default Key Functions” on page 142.
DSMC SIDE HANDLE
Front (left), DSMC SIDE
HANDLE Rear (right)
DSMC SIDE HANDLE (Top)

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |18
INSTALL DSMC SIDE HANDLE
WARNING: The DSMC SIDE HANDLE is NOT HOT SWAPPABLE, meaning you cannot remove or install the DSMC
SIDE HANDLE while the camera is powered on. Before installing or removing the DSMC SIDE HANDLE, you
MUST power down the camera. Failure to do so may result in damage to the DSMC SIDE HANDLE or DSMC
that will not be covered under warranty.
REQUIRED TOOL: T10 Torx®driver
1. Power down the camera.
2. Use a T10 Torx driver to remove the single screw located at the bottom of the brain side plate (if installed).
3. Rotate the brain side plate upwards to disengage the lip at the top of the side plate from the camera brain,
and remove the brain side plate.
4. Insert the lip at the top of the DSMC SIDE HANDLE into the area where the lip from the brain side plate
was installed.
5. Press the DSMC SIDE HANDLE down flush along side of camera brain.
6. Rotate the thumbscrew upward while applying steady pressure until tight.
REMOVE DSMC SIDE HANDLE
WARNING: The DSMC SIDE HANDLE is NOT HOT SWAPPABLE, meaning you cannot remove or install the DSMC
SIDE HANDLE while the camera is powered on. Before installing or removing the DSMC SIDE HANDLE, you
MUST power down the camera. Failure to do so may result in damage to the DSMC SIDE HANDLE or DSMC
that will not be covered under warranty.
1. Power down the camera.
2. Rotate the thumbscrew downward until the DSMC SIDE HANDLE detaches from the camera body.
3. Pull the bottom of the DSMC SIDE HANDLE away from the brain to disengage the lip at the top of the DSMC
SIDE HANDLE away from the camera brain.
4. Remove the DSMC SIDE HANDLE from the camera.
DSMC MODULES
WARNING: The DSMC modules are NOT HOT SWAPPABLE, meaning you cannot remove or install the modules
while the camera is powered on. Before installing or removing modules, you MUST power down the camera.
Failure to do so may result in damage to the modules or DSMC that will not be covered under warranty.
PRO I/O MODULE
The PRO I/O MODULE brings together the essential I/O connections into one module, providing a central hub
for professional audio and video components.
Centralized ports make it easy to manage connections and cables.
LCD/EVF port allows you to connect an additional RED LCD or EVF.
Customize triggers and interface with third-party GPIO and RS232 control devices using RED PRO I/O
cables.
Attach an additional DSMC module or a REDMOTE to the back of the PRO I/O MODULE for additional ex-
pansion.

RED DSMC OPERATION GUIDE
COPYRIGHT © 2013 RED.COM, INC 955-0020_V5.1, REV-D |19
Internal cooling system maintains appropriate operating temperature.
REAR SSD MODULE
The REAR SSD MODULE secures onto the back of the DSMC brain to serve as a rear location for recording
onto 1.8” REDMAG SSD media.
QUAD BATTERY MODULE
The QUAD BATTERY MODULE holds up to four REDVOLTs or two REDVOLT-XLs.
PRO I/O MODULE
REAR SSD MODULE

COPYRIGHT © 2013 RED.COM, INC
RED DSMC OPERATION GUIDE
955-0020_V5.1, REV-D |20
Batteries may be hot swapped.
DUAL BATTERY MODULE
The DUAL BATTERY MODULE holds up to two REDVOLTs.
Batteries may be hot swapped.
INSTALL MODULES
Use the instructions in this section to install and remove DSMC modules.
INSTALL MODULE ADAPTOR
Use the instructions in this section to install the MODULE ADAPTOR.
REQUIRED TOOL: T20 Torx®driver
You must install a MODULE ADAPTOR to the back of the camera brain before you install a DSMC module.
MODULE ADAPTORs are sold separately from the DSMC modules.
1. Power down the camera.
2. Remove the REDMOTE, if attached.
QUAD BATTERY MODULE
DUAL BATTERY MODULE