Red One RO – BB User manual

RO –BB Heavy Duty Commercial Blender
Owner’s Manual
Read and Save These Instruction
Model:BL-060A
TELEPHONE: SERVICE (44) 01332 875665
FAX: SERVICE (44) 01332 875536

Important Safeguards:
1. Read all instructions.
2. Do not put motor base in water or other liquid.
3. Unplug the power cord from the wall outlet when the machine is not in use, before putting on or taking off
parts and before cleaning; other than washing the container.
4. Do not use outdoors.
5. Do not let the power cord hang over edge of table or counter, or touch hot surfaces.
6. Keep hands and utensils out of the container while motor is running. A rubber scraper may be used, but
only when the blender is not running.
7. CAUTION: Blade is sharp. Handle carefully.
Never try to remove blade while container is sitting on the motor base.
Do not operate with loose or damaged blades.
8. Always operate with the lid in place.
9. To avoid scratching only use a soft cloth to wipe the control panel area clean.
Features:
RO-BB Blender combines a high powered motor with stainless steel blades for easy blending.
Built-in design
Multi functional
Wet and dry application
Two in one stainless steel cutting blades
Industrial high speed motor capable of crushing ice in seconds
Food Quality transparent Polycarbonate jug –virtually unbreakable
Over-current and overheating protection fitted.
Safe to use –will not operate without jug in correct place.
LCD display window
Intelligent digital control panel
1500W Motor
2 Litre capacity Jug
Operating Instructions:
For making a fruit smoothie
1. Put the ingredients (Ice, fruit and water) into the container and replace the lid. When making thicker drinks,

please use the blending stick.
2. Set the variable button to a high speed
3. Turn on SET Switch, if liquid is limited, please use the stick.
4. After 3-5 seconds later, the blending sounds will diminish, the process is then complete.
Blending Fruit & Vegetables
1. Put fruit (or vegetables) and a little water into the container.
2. Set to medium or high speed.
3. Turn on SET switch. When the contents are smooth (after 4-6 seconds), stop the machine at once to
prevent over blending.
Note:
1. Pulsing switch is mainly for testing or blending special materials do not use it frequently.
2. Do not run more than 2 minutes when blending dry materials.
Control Panel
Digital Control Panel
Power Switch
Located on the side of the motor Base the ON/OFF switch controls the power to the machine. Plug in the
machine and switch ON.
ON/OFF Switch
Pressing START/STOP once starts and runs the machine and turns the blades. Press the START/STOP button
again to stop the machine and the blades.
PRE-SET Time buttons
These buttons, 8S, 12S, 60S, 90S are pre-programmed blending cycles, designed for the most commonly
made drinks. Depending on the viscosity of the drink you are creating, pressing one of the PRE-SET Time
buttons will run the machine for a full cycle. The machine will stop by itself when the cycle is complete. Acycle
varies in length; see the Instruction on next page for a complete description of the range of each PRE-SET
button. Due to the difference in recipes, your results may vary.

DISPLAY WINDOW
This counts down operation time remaining
HIGH/LOW PULSE buttons
These are pulse buttons, when you press H Pulse button, the machine will run at the highest speed, and when
you press L Pulse button, the machine will run at 60% of the highest speed. Every press will activate 0.5
seconds running.
IMPACT Button
This button has a pre-set a common programme. Once selected, the blender will automatically run in a cycle:
activating the blending speed to highest for 0.5 seconds then stop for 1.5 seconds, then run again, returning to
the highest speed for 0.5 second, then stop for 1.5 seconds. The machine will run this cycle 10 times, finishing
at the highest speed. The whole programme lasts 30 seconds.
Instructions
How to operate your blender using the PRE-SET Time buttons.
8S (8 Seconds) Blends thin drinks with just juice and ice.
This program will quickly ramp to a high blending speed for 8 seconds.
12S (12 Seconds) Blends light coffee drinks.
This button will ramp the blending speed to highest speed for 6 seconds, then ramp down to medium
speed for 6 seconds.
30S (30 Seconds) Creates a specialty drink with a thick viscosity.
This button runs at a highest speed for 15 seconds, then ramp down to medium speed for 15
seconds.
60S (60 seconds) Blends a regular smoothie.
This button runs for 30 seconds at the highest speed, then decreases and runs on medium speed
for 30 seconds.
1. Place liquids and soft foods in the Jug first, followed by solid items lastly the ice. Prepare food by cutting or
breaking into 1-3 in. (2.54-7.62 cm) pieces. Frozen fruit, especially, should be as small as practical.
Thawed or partially thawed fruit is recommended. We recommend Time button # 60S or # 90S for
heavy-duty blending.
2. Set the container on the motor base by aligning it over the centering pad anchored to the base. (Motor
must be completely stopped before positioning container).
Containers are not to be used for hard, dry materials.Avoid running the blender with the container empty.
3. Always use a lid when blending.
4. Select desired programmed setting by pressing any of the Pre-Set Time button. The machine will begin
immediately to cycle through the selected program, and turn off when the program is complete. Each
button has a different pre-selected combination of speed and length for blending.
NOTE: If you detect a change in the sound of the machine or if a hard or foreign object comes into contact
with the blades inspect your blade assembly for loose, damaged or missing parts. Press ON/OFF button to
stop the blending cycle.
5. When the cycle is complete the blender stops, wait until the blades comes to a complete stop before
removing the lid and/or container from the motor base.
6. Remove the container, pour, garnish and serve the drink.
Notes:

On all units the built-in thermal sensor keeps track of how hot the motor is running and will
automatically switch off if the motor is overheating. User should remove the container and run the
machine until cool. This takes about 2 minutes.
Please check your operation when the motor is overheated. If the machine is in constant use or the
material is too thick, it could lead to overheating.
Specification
Model
RO-BBUC
Voltage
220-240V~50/60Hz, 120V~60Hz
Capacity
2000c.c
Endurance of Container
-40º~180º
Power
1500W
Weight
5.5kgs
Length of Cord
1.8M
Dimension
17x12x13 1/2 Inches
Protector
Current protector, Thermal protector for motor
Cleaning Instructions
Ensure that the blender jug is sitting on the base properly before proceeding.
Add warm water to halfway.
Add one or two drops of washing-up liquid; and if available, add half a lemon; the rind will scrape off any
remaining particles and the juice and rind will help to eliminate odours.
Place the lid on the blender.
Press the low blend button and allow to blend for up to 30 seconds.
Check that it has caught all the particles.
Pour the liquid away
Rinse out well with cold water
Place upside down on a rack to air dry. Wipe down the base with a damp cloth and allow to air dry.
Tips
Ensure that the entire appliance is dry before storage.
It is always a good idea to wipe the base and wash the jug as quickly as possible after use.
Warnings:
Make sure the spout is closed when you are blending the cleaning liquid.
Take care to remove the cord from the power socket before wiping down the base with a damp cloth.
Take care when handling the blender blades