Redon GTR User manual

REDON GTR
USER MANUAL
redon.com

redon.com

3
Technical Specications
Packaging
Removing Axis Locking Holder
Product Contents and Options
Working Conditions
Considerations
Processable Materials & Types
Pos
User Inteace
Load Programs and Running Programs
User Inteace / RUN - Sta / Auto
User Inteace / JOG - Manual Movement
User Inteace / ATC
User Inteace / Twin Tool
User Inteace / UTILITY
Utulity / Maintenance
Equipment
User Inteace / UTILITY
Notes
4 - 5
6 - 10
11 - 14
15 - 16
17
18
19
20 - 22
23 - 32
33 - 36
37 - 40
41 - 43
44- 53
54 - 57
58 - 60
61 - 66
67 - 71
72 - 82
83 - 87
CONTENTS

4
redon.com
Country of Origin
Axis Motor Technology
Control Unit
Ball Screw Precision
Max. Spindle Speed
Max. Spindle Power
Number of Axes
Max. Slope Angle of B Axis
Max. Tool Sha Diameter
ATC Capacity
Dry Milling
Wet Milling
CoCr Milling
Titanium Milling
Glass-Ceramic Milling
Turkey
Digital AC Servo Motor
B&R, 5 Axis, Digital, Simultaneous
8µm
60.000RPM
3700W
5 Axis
-30 / +120 Degrees (A Axis)
-30 / +210 Degrees (B Axis)
3 / 4 / 6mm
12
Yes
Yes
Yes
Yes
Yes
TECHNICAL SPECIFICATIONS
REDON GTR

5
Zirconia Milling
Preform Milling
Plastic Milling
Peek Milling
Composite Milling
Alumina Milling
Referencing Milling Requirement
Voltage / Frequency
Power Consumption
Pressurized Air Requirement (L/Min)
Min. Air Pressure (Bar)
Volume (m³)
CAM Soware
Device Dimensions
Yes
Yes
Yes
Yes
Yes
Yes
No
110v-230v / 50-60Hz
300W - 400W
50
6
0.26
Open System
630mm x 660mm x 780mm

6
redon.com
Images show the upper cover of the shipping case. The upper cover has 4 lateral suaces.
With 2 clamps on each lateral suace, there are 8 clamps in total.
UNPACKAGING
To remove the upper
cover, move the clamps
on the upper cover to
the upright position as
shown in the image using
a screwdriver and a
hammer.
1
2
3

7
This image shows how you can detach the side clamps to remove the side covers. You need to detach all
side cover clamps in order to remove the side covers.
UNPACKAGING
Removing the upper cover with its clamps in the upright position
31
2

8
redon.com
UNPACKAGING
The side suaces can be removed as
described above. This image shows
a shipping case with one of its side
covers removed.
Do not use a box
cuer to open
the package.
Use scissors to cut the plastic strip around the package.
1 2 3

9
UNPACKAGING
Move the Redon GTR CAD/CAM machine onto the Redon machine table by
grabbing the right and le carry handles.

10
redon.com
Open the package in the direction of the arrows as shown in the sample images.
Do not use a box cuer
to open the package.
Cut the package wrap with scissors
in the direction of the arrows as
shown in sample images 1 and 2.
1
2
UNPACKAGING

11
REMOVING AXIS LOCKING HOLDER
Remove the axis locking gear from the spindle housing using a pair of pliers. Make sure that you loosen the
tensioning bolt of the axis locking gear using an 11-mm open-end wrench. Then, move the Z axis upward
by using the JOG command on the user inteace.
The Axis Locking Gear is
used during shipment of
the machine to prevent the
axes of the machine from
moving. It is the rst pa
that you will see aer you
open the door following
unpackaging.
Axis Locking Gear

12
redon.com
REMOVING AXIS LOCKING HOLDER
Side view image showing how to
loosen the tensioning bolt.
Move the Z axis to the limit
in the positive direction and
then remove the bolts of
the axis locking gear. Z AXIS

13
REMOVING AXIS LOCKING HOLDER
The third bolt is not visible in the image above. As
shown in the sample image, the third bolt located
at the back must also be removed.
The axis locking gear is
fastened to the semi-circular
block retaining ring with
three 6-mm bolts. You can
unscrew these bolts by
turning them counterclockwise
with a wrench.

14
redon.com
REMOVING AXIS LOCKING HOLDER
1
22
While suppoing the axis locking gear from underneath, move the Z axis in
the positive direction via the machine’s user inteace. Do not move the Z
axis in the positive direction before making sure that the bolts fastening
the axis locking gear to the Spindle Housing are completely removed.

15
PRODUCT CONTENTS
8 mm x 7.5 mt
Pneumatic Hose 1 Pc
Network Cable
5 mt
Air Gun

16
redon.com
OPTIONS
M136 Block Retaining
Ring, Upper – 1 pc
M5 x 20 Socket Head
Cap Screw A3 – 6 pcs
M135 Block Retaining
Ring, Lower – 1 pc
M4 x 16 Socket Head
Cap Screw A3 – 6 pcs
Glass-Ceramic
and Premill HolderTable
Digital Caliper Cuing Oil

17
WORKING CONDITIONS
Proper working conditions must be provided for the bench according to
the technical specications sent aer purchase.

18
redon.com
CONSIDERATIONS
When the machine needs to be moved or re-located, the carry handles must be used. Since the machine’s
body is made of composite materials, it may get broken when moved or lied.
If the machine is to be placed on a table other than its original table, that table must be able to withstand a load
of 250 kg. The dimensions of the table must not be smaller than the dimensions of the machine.
1
2
It must be ensured that
no pressurized air or water
is applied to the area encircled
in red in the image below.

19
PROCESSABLE MATERIALS & TYPES
Abuments
Hybrid Abutment
Model
Surgical Guide
Implant Bar
Crown Bridge
Inlay, Onlays, Veneer
Screw Retantion Bridge
Telescope Abutment
Premill Abutments
Denture
Model Casting
Splint
Telescope

20
redon.com
PORTS
6-Bar Air Inlet. Connect the
8mm pneumatic hose to the air
compressor.
Ensure that the air is dry and clean.
Otherwise, air-operated pas
including the spindle motor may be
damaged.
Power Buon (On/O). When the buon is
in position (0), the machine is o. When the
buon is in position (1), the machine is on.
Back Panel
1
1
2
2
3
3
8mm x 7.5m Pneumatic Hose – 1 pc