Redx RX-2505PW User manual

This drawing is for reference only. Please refer to the actual product.
≥300mm ≥300mm
600
900
The size and parameters of the product are subject to change without notice.
http:// www.redxenergy.com.au
APP Download
All-In-One Energy Storage System
www.redxenergy.com.au
RX - 2505PW
Safety Statement
Danger
Warning
Warning
Notice
Packing List
Installation Location
Dimension
145
This document is subject to change from time to time due to product upgrades or other reasons.
This document is not a substitute for the user manual or safety instructions.
Please read the user manual and related standards before undertaking any operation or
commissioning. Please take time to accesshttp://www.redxenergy.com.au or scan the QR code for
the latest quick installation guide.
Failure to comply with any of the above requirements may result in injury to personnel or damage
to equipment.
Prior to commencement, check whether the goods match the packing list, if there is any damage
to any items or components missing, please contact the Distributor / Dealer or Redx.
The power cables must be intact and well insulated. Please use insulating gloves and wear personal
protective equipment at all times when installing this product.
All safety labels, warning labels, andnameplates must be clear and visible andcannot be
removed or overwritten.
Hot surface!
Inverter module may become hot after extended period of operation. Allow time for inverter
to cool before touching!
The country setting and protection parameters must be set by professional personnel based
on local power grid standards.
Incorrect country settings may affect the operation failure to meet the local standard.
Warning Label
Disconnect all external power supplies before
maintainace.
Device only has high voltage on AC input and
AC output. professional and qualified technicians
are not required to install this unit.
Hot surfaces！
Read the instructions before
operation.
Wait for 5 minutes before touching the internal conductive components after system
turn off and disconnected from grid.
RX-2505PW
1PCS 1PCS 8PCS 1PCS 1PCS
5PCS 1PCS 1PCS 1PCS 1PCS
5min
Shock hazard！
Exposure to sunlight and the elements are not recommended.
All electrical connections must meet local and national electrical standards.
Only connect the system to the grid with local authority approval .
Redx shall not be liable for any loss of life or damage caused by failure to comply with the
requirements of this document and user manual.
Hot surface
Warranty will be void if the cover is removed. Improper opening of the unit may also result in
serious electrical shock or injury to personnel.
RJ45 M6 bolts
M4 Document M5 lugs
4 Pin CT
connector CT
Bracket Hole template
Information

Notice
Installation
Grounding Connection
31
5
2
Hole template Hole template Expansion Bolts
Rx-2505
Bracket
6
1 3 5
24
Pre - operation inspection
Nut / washer Bracket
4
673
4
Negative DC1
conductor
Negative DC 2
conductor
Positive DC1
conductor
positive DC 2
conductor
Nut
Nut
1 5
2
Double core DC conductor
Connector
Avoid water and electricity when drilling, bit size φ8mm, drilling depth 40mm.
This figure is for reference only, please refer to the actual product!
①
②
③
④
⑤
⑥
⑦
The installation location meets the requirement.
Checking Items
The system has been securely installed.
Sufficient space for heat dissipation. No objects are left in the system.
System wiring is correct and firm. Refer to 240V diagram document.
Cables are properly installed and well protected without any damage.
All terminals have been sealed.
Warning labels are not covered without alteration or occlusion.
Result
YES NO
If the startup fails, refer to "Troubleshooting" in the user manual.
For details about LED indicators, refer to the user manual.
③
Operation
Following the steps to start the system.
①Step : Connect to the grid ( if available) and connect PV or Wind to DC1 and DC2.
②
Step : Turn on the battery isolation circuit breaker.
Step : Turn on the power button.
Step④ : Download the Redx Power App, QR code for App download is on flip side of document
Step ⑤ : Complete all steps in the App instructions.
DC2-
DC2+
Wind Turbine
Controller
RX - 2505PW
Grid
EPS Load
1 DRM0_1
2 DRM0_2
3 /
4 /
1
2
3
4
5 /
6 /
7 /
8 /
8 9
0.8
DRM0
Connect cables to DC1 and DC2（Optional function）
Connect cables to DC1 and DC2：
The functions of Wind Turbine and PV Arrays can be installed according to the needs of customers.
DC1+
DC1-
optimizer
(one for each panel)
PV Array
DC1
DC2
DC1
DC2
CT-METER
RX-2505PW
Mark
Mark
4Pin
connector
CT+
CT-
/
/
Circuit Breaker
Circuit Breaker
Operating
status
AC-ON Normal – Green
Fault – Red
Grid connected – Green
Grid disconnected – Blue
Charging – Green
Discharging – Blue
DC
GRID
CHG
BATT Battery status
BATT
LED Status
NO DC – Led off
DC1 > 100W – Green (Flash)
DC2 > 100W – Blue (Flash)
DC1&DC2 > 100W – Yellow (Flash)
CT/meter Installation
AC input / output
The CT with the"GRID"
label is attached to
the L line of the power
grid. The "GRID" CT
arrow points towards
the grid. The CT must
be installed inside the
switchboard.
Refer to 240v diagram for
more information.
Divert load
4 Pin Connector diagram on the unit

四折页尺寸: 566*209mm
材质/克重: 200g铜版纸 四色正反印 四折页